ULR2W3R9MNL1GS

ALUMINUM ELECTROLYTIC CAPACITORS ULR Chip Type, High Voltage. Chip Type, high Voltage. Applicable to automatic mounting machine using carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. ULV ULR Long Life High Voltage UUX Specifications Item Performance Characteristics Category Temperature Range –40 to +105°C Rated Voltage Range 160 to 500V Rated Capacitance Range 2.7 to 39µF Capacitance Tolerance Leakage Current ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.04CV +100(µA). Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) Measurement frequency : 120Hz at 20°C 160 0.20 200 0.20 250 0.25 400 0.25 450 0.30 500 0.30 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio ZT / Z20 (MAX.) Z–40°C / Z+20°C 160 200 250 400 450 500 6 6 10 10 15 15 Capacitance change tan δ Leakage current Within ±20% of the initial capacitance value 200% or less than the intial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 3000 hours at 105°C. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the characteristic requirements listed at right when they are removed from the plate. Chip Type Type numbering system (Example : 400V 8.2µF) (φ8 , φ10) Positive C±0.2 0.3MAX. Series Capacitance A B C E L H 5 6 7 8 9 10 11 12 13 14 Capacitance tolerance (±20%) Negative Rated voltage (400V) Series name (mm) 10 × 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1 4 Configuration Pressure relief vent 8 × 10 10 × 10 2.9 3.2 8.3 10.3 8.3 10.3 3.1 4.5 10 10 0.8 to 1.1 0.8 to 1.1 3 Rated capacitance (8.2µF) H L±1.0 2 Taping code A±0.2 E A±0.2 B±0.2 φD±0.5 A2 8.2 2G LR Lot No. 1 U L R 2 G 8 R 2 MN L 1 GS 0.5MAX. Plastic platform Voltage(2G : 400V) φD × L Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Black print on the case top. Marking Trade mark Capacitance change tan δ Leakage current Type Voltage V 160 200 250 400 450 500 Code 2C 2D 2E 2G 2W 2H Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.80 120 Hz 1.00 300 Hz 1.25 1 kHz 1.40 10 kHz or more 1.60 Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS ULR ■ Dimensions Rated Voltage （V） （code） 160 （2C） 200 （2D） 250 （2E） 400 （2G） Part Number 196 50 ULR2C150MNL1GS 0.20 272.8 65 ULR2C270MNL1GS 0.20 349.6 70 ULR2C390MNL1GS 8× 10 0.20 196 50 ULR2D120MNL1GS 10× 10 0.20 276 65 ULR2D220MNL1GS 10× 13.5 0.20 364 70 ULR2D330MNL1GS 10 8× 10 0.25 200 35 ULR2E100MNL1GS 15 10× 10 0.25 250 50 ULR2E150MNL1GS 22 10× 13.5 0.25 320 55 ULR2E220MNL1GS 4.7 8× 10 0.25 175.2 35 ULR2G4R7MNL1GS 8.2 10× 10 0.25 231.2 50 ULR2G8R2MNL1GS Case Size φD×L（mm） tan δ 15 8× 10 0.20 27 10× 10 39 10× 13.5 12 22 33 12 450 （2W） （ ） 10× 13.5 0.25 292 55 ULR2G120MNL1GS 3.9 8× 10 0.30 170.2 25 ULR2W3R9MNL1GS 6.8 10× 10 0.30 222.4 40 ULR2W6R8MNL1GS 10 500 （2H） Leakage Current （µA） at 20℃ after 1 minute Rated Ripple （mArms） （105℃/120Hz） Rated Capacitance （µF） 10× 13.5 0.30 280 45 ULR2W100MNL1GS 2.7 8× 10 0.30 154 20 ULR2H2R7MNL1GS 3.9 10× 10 0.30 178 35 ULR2H3R9MNL1GS 5.6 10×13.5 0.30 212 40 ULR2H5R6MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K