ULT2C220MNL1GS

ALUMINUM ELECTROLYTIC CAPACITORS ULT Chip Type, High Voltage. High Temperature Range. Chip type, high voltage and high temperature range. Load life of 2000 hours at +125°C. Applicable to automatic mounting machine ULH using carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. Long Life ULT High Voltage UUB Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Performance Characteristics –40 to +125°C 160 to 500V 1.8 to 33µF ± 20% at 120Hz, 20°C Leakage Current Rated voltage (V) – Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 160~450 0.04CV+100(µA)max.(1 minute's at 20°C) 500 0.04CV+200(µA)max.(1 minute's at 20°C) Measurement frequency : 120Hz at 20°C 160 0.20 200 0.20 250 0.25 400 0.25 450 0.30 500 0.30 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio Z–40°C / Z+20°C ZT / Z20 (MAX.) 160 200 250 400 450 500 6 6 10 10 15 15 The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 125°C. Endurance Shelf Life Resistance to soldering heat Marking C±0.2 0.3MAX. Series 4 5 6 7 8 9 10 11 12 13 14 Taping code Configuration Capacitance tolerance (±20%) Negative Pressure relief vent 8 × 10 10 × 10 2.9 3.2 10.3 8.3 10.3 8.3 3.1 4.5 10 10 0.8 to 1.1 0.8 to 1.1 3 Rated capacitance (6.8µF) H L ±1.0 2 U L T 2 G 6 R 8 MN L 1 GS A±0.2 E A±0.2 B±0.2 φD±0.5 A2 6.8 2G LT Lot No. Capacitance 1 Positive Plastic platform 0.5MAX. (φ8 , φ10) A B C E L H Leakage current Type numbering system (Example : 400V 6.8µF) Voltage(2G : 400V) φD × L Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value tan δ After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they Less than or equal to the initial specified value tan δ shall meet the characteristic requirements listed at right Less than or equal to the initial specified value Leakage current when they are removed from the plate. Black print on the case top. Chip Type Trade mark Capacitance change Rated voltage (400V) (mm) Series name 10 × 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1 Type Voltage V 160 200 250 400 450 500 Code 2C 2D 2E 2G 2W 2H Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS ULT ■ Dimensions Rated Voltage （V） （code） 160 （2C） 200 （2D） Rated Capacitance （µF） 400 （2G） 500 （2H） 196 45 ULT2C150MNL1GS 0.20 240.8 60 ULT2C220MNL1GS 0.20 311.2 65 ULT2C330MNL1GS 15 8× 10 0.20 22 10× 10 33 10× 13.5 （ ） 12 8× 10 0.20 196 45 ULT2D120MNL1GS 18 10× 10 0.20 244 60 ULT2D180MNL1GS 27 10× 13.5 0.20 316 65 ULT2D270MNL1GS 8×10 0.25 182 30 ULT2E8R2MNL1GS 15 10× 10 0.25 250 45 ULT2E150MNL1GS 18 10× 13.5 0.25 280 50 ULT2E180MNL1GS 3.9 8×10 0.25 162.4 30 ULT2G3R9MNL1GS 6.8 10× 10 0.25 208.8 45 ULT2G6R8MNL1GS 10 450 （2W） Part Number tan δ 8.2 250 （2E） Leakage Current （µA） at 20℃ after 1 minute Rated Ripple （mArms） （125℃/120Hz） Case Size φD×L（mm） 10× 13.5 0.25 260 50 ULT2G100MNL1GS 3.3 8× 10 0.30 159.4 20 ULT2W3R3MNL1GS 5.6 10× 10 0.30 200.8 35 ULT2W5R6MNL1GS 7.5 10×13.5 0.30 235 40 ULT2W7R5MNL1GS 1.8 8× 10 0.30 236 20 ULT2H1R8MNL1GS 3.3 10×10 0.30 266 35 ULT2H3R3MNL1GS 4.7 10 ×13.5 0.30 294 40 ULT2H4R7MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K