UMT0G470MDD1TP

ALUMINUM ELECTROLYTIC CAPACITORS UMT 5mmL, Wide Temperature Range Wide temperature range of – 55 to +105°C, with 5mm height. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). UMV UMT Long life High Temperature UMA Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Voltage Range 4 to 50V Rated Capacitance Range 1 to 100µF Rated Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C 4 0.37 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 6.3 0.28 10 0.24 16 0.20 25 0.16 35 50 Figures in ( ) are for 0.13 (0.14) 0.12 (0.14) φ 3 product. Measurement frequency : 120Hz Stability at Low Temperature The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance 50 2 3 35 2 3 25 2 3 16 2 4 10 3 5 6.3 3 8 4 6 12 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio (MAX.) Z– 40°C / Z+20°C < 16V) Within ±25% of the initial capacitance value (φ 3mm unit,and = > 25V) Within ±20% of the initial capacitance value ( = Capacitance change 200% or less than the initial specified value tan δ Leakage current Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Marking Printed with white color letter on black sleeve. Radial Lead Type Type numbering system (Example : 25V 10µF) Sleeve (P.E.T.) 2 3 4 5 6 7 8 9 10 11 12 UMT 1 E 1 0 0 MDD Sleeve (P.E.T.) 1 φd P±0.5 P±0.5 φ D+0.5 MAX. φ D+0.5 MAX. 1 φd (φ 3 : P±0.3) 2 3 4 5 6 7 8 9 10 11 12 UMT 1 E 1 0 0 MDD φD 2 2 4 to 6.3 Code — Size code φ D 3 2 Configuration 1 2 4 to 6.3 — Size code Capacitance tolerance (±20%) Configuration 1 Rated capacitance (10µF) Capacitance tolerance (±20%) Rated voltage (25V) Rated capacitance (10µF) Series name Rated voltage (25V) Type Series name (φ 3 : P±0.3) (mm) φD L+1MAX. L+1MAX. 15 MIN 15 MIN 4 MIN 4 MIN 3 4 5 6.3 P 1.0 1.5 2.0(mm)2.5 φ D φ d 3 0.404 0.455 0.45 6.3 0.45 P 1.0 1.5 2.0 2.5 φ d 0.40 0.45 0.45 0.45 • Please refer to page 18 about the end seal configuration. 1 Configuration φD 1 Configuration 3 Code 3 Pb-free leadwire Pb-free PET sleeve Type CD leadwire φ D4 to 6.3 Pb-free DD Pb-free PET sleeve 2 For φ 3mm unit, place 3 CD size code of 2 to 12th digit. 4 to 6.3 Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 DD 2 For φ 3mm unit, place size code of 2 to 12th digit. 10 kHz or more 1.50 Dimension table in next page. CAT.8100J ALUMINUM ELECTROLYTIC CAPACITORS UMT ■ Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 22 4 （0G） 6.3 （0J） 10 （1A） 16 （1C） 25 （1E） 50 （1H） 4× 5 tan δ 0.37 Leakage Current （µA） at 20℃ after 2 minutes （ ） Rated Ripple （mArms） （105℃/120Hz） Part Number 22 UMT0G220MDD 3 33 5× 5 0.37 3 30 UMT0G330MDD 47 5×5 0.37 3 36 UMT0G470MDD 100 6.3×5 0.37 4 60 UMT0G101MDD 22 4× 5 0.28 3 22 UMT0J220MDD 33 5× 5 0.28 3 30 UMT0J330MDD 47 5× 5 0.28 3 36 UMT0J470MDD 100 6.3× 5 0.28 6.3 60 UMT0J101MDD 22 5×5 0.24 3 27 UMT1A220MDD 33 5× 5 0.24 3.3 35 UMT1A330MDD 47 6.3× 5 0.24 4.7 46 UMT1A470MDD 10 4× 5 0.20 3 18 UMT1C100MDD 10 3× 5 0.20 3 14 UMT1C100MCD2 22 5× 5 0.20 3.52 30 UMT1C220MDD 33 6.3× 5 0.20 5.28 40 UMT1C330MDD 47 6.3× 5 0.20 7.52 50 UMT1C470MDD 4.7 4× 5 0.16 3 13 UMT1E4R7MDD 4.7 3× 5 0.16 3 10 UMT1E4R7MCD2 5× 5 0.16 3 23 UMT1E100MDD 10 22 6.3×5 0.16 5.5 38 UMT1E220MDD 33 6.3× 5 0.16 8.25 48 UMT1E330MDD 3× 5 0.14 3 2.2 35 （1V） Case Size φD×L（mm） 7.5 UMT1V2R2MCD2 3.3 4× 5 0.13 3 11 UMT1V3R3MDD 3.3 3× 5 0.14 3 9 UMT1V3R3MCD2 4× 5 0.13 3 15 UMT1V4R7MDD 10 4.7 5× 5 0.13 3.5 25 UMT1V100MDD 22 6.3× 5 0.13 7.7 48 UMT1V220MDD 1 4× 5 0.12 3 6.2 UMT1H010MDD 1 3× 5 0.14 3 5.9 UMT1H010MCD2 2.2 4× 5 0.12 3 11 UMT1H2R2MDD 2.2 3× 5 0.14 3 9 UMT1H2R2MCD2 3.3 4× 5 0.12 3 14 UMT1H3R3MDD 4.7 10 5× 5 0.12 3 19 UMT1H4R7MDD 6.3× 5 0.12 5 30 UMT1H100MDD For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ). If there is no size code in the part number, please add size code “1” and then add the appropriate code. Please refer to page 18, 19 about the formed or taped product spec. Please refer to page 4 for the minimum order quantity. CAT.8100J