UMW1H010MDD1TP

ALUMINUM ELECTROLYTIC CAPACITORS UMW 5mmL, For General Audio Equipment Acoustic series, with 5mm height. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). USW Smaller UMW Specifications Performance Characteristics Item Category Temperature Range –40 to +85°C Rated Voltage Range 4 to 50V Rated Capacitance Range 1 to 470µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 4 0.35 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 6.3 0.24 10 0.20 16 0.16 25 0.14 35 0.12 50 0.10 Measurement frequency : 120Hz 4 7 15 Rated voltage (V) Stability at Low Temperature Impedance ratio (MAX.) Z– 25°C / Z+20°C Z– 40°C / Z+20°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C. Endurance 25 2 4 16 2 4 10 3 6 6.3 4 8 Capacitance change tan δ Leakage current 35 2 3 50 2 3 Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Printed with black color letter on gold sleeve. Shelf Life Marking Radial Lead Type Type numbering system (Example : 25V 10µF) 1 φd Sleeve (P.E.T.) 2 3 4 5 6 7 8 9 10 P ±0.5 P ±0.5 φD+0.5 MAX. φD+0.5 MAX. L+1MAX. L+1MAX. 15MIN 11 2 3 4 5 6 7 8 9 10 11 U 1M W 1 E 1 0 0 MDD U MW 1 E 1 0 0 M D D φd Sleeve (P.E.T.) 4MIN 15MIN 4MIN Configuration (mm) φD 4 5 6.3 8 (mm) P φD 1.5 4 2.0 5 2.56.3 2.5 8 φd P 0.451.50.452.00.452.5 0.452.5 φd 0.45 0.45 0.45 0.45 Configuration Pb-free leadwire Configuration φD 4 to φ8 D 4 to 8 Configuration Capacitance tolerance (±20%) Capacitance tolerance (±20%) Rated capacitance (10µF) Rated capacitance (10µF) Rated voltage (25V) Rated voltage (25V) Series name Series name Type Type Pb-free PET sleeve Pb-free leadwire Pb-freeDD PET sleeve DD Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Dimension table in next page. CAT.8100J ALUMINUM ELECTROLYTIC CAPACITORS UMW Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 33 4 （0G） 6.3 （0J） 10 （1A） 16 （1C） 50 （1H） 0.35 Leakage Current （µA） at 20℃ after 2 minutes （ ） Rated Ripple （mArms） （85℃/120Hz） Part Number 28 UMW0G330MDD 3 47 4× 5 0.35 3 33 UMW0G470MDD 5× 5 0.35 4 56 UMW0G101MDD 220 6.3× 5 0.35 8.8 96 UMW0G221MDD 330 8× 5 0.35 13.2 145 UMW0G331MDD 470 8× 5 0.35 18.8 185 UMW0G471MDD 22 4× 5 0.24 3 28 UMW0J220MDD 33 5× 5 0.24 3 37 UMW0J330MDD 47 5× 5 0.24 3 45 UMW0J470MDD 100 6.3×5 0.24 6.3 70 UMW0J101MDD 220 8× 5 0.24 13.86 110 UMW0J221MDD 20.79 170 UMW0J331MDD 33 UMW1A220MDD 330 8× 5 0.24 22 5× 5 0.20 3 33 5× 5 0.20 3.3 41 UMW1A330MDD 47 6.3× 5 0.20 4.7 52 UMW1A470MDD 100 8× 5 0.20 10 80 UMW1A101MDD 220 8× 5 0.20 22 135 UMW1A221MDD 10 4× 5 0.16 3 23 UMW1C100MDD 22 5× 5 0.16 3.52 37 UMW1C220MDD 33 6.3× 5 0.16 5.28 49 UMW1C330MDD 47 6.3× 5 0.16 7.52 58 UMW1C470MDD 4.7 35 （1V） 4× 5 tan δ 100 100 25 （1E） Case Size φD×L（mm） 8×5 0.16 16 92 UMW1C101MDD 4× 5 0.14 3 16 UMW1E4R7MDD 10 5× 5 0.14 3 27 UMW1E100MDD 22 6.3× 5 0.14 5.5 42 UMW1E220MDD 33 6.3× 5 0.14 8.25 52 UMW1E330MDD 47 8× 5 0.14 11.75 100 8× 5 0.14 25 70 UMW1E470MDD 110 UMW1E101MDD 3.3 4× 5 0.12 3 15 UMW1V3R3MDD 4.7 4× 5 0.12 3 18 UMW1V4R7MDD 10 5× 5 0.12 3.5 29 UMW1V100MDD 22 6.3× 5 0.12 7.7 46 UMW1V220MDD 33 8× 5 0.12 11.55 62 UMW1V330MDD 47 8× 5 0.12 16.45 80 UMW1V470MDD 1 4× 5 0.10 3 2.2 4× 5 0.10 3 8.4 13 UMW1H010MDD UMW1H2R2MDD 3.3 4× 5 0.10 3 17 UMW1H3R3MDD 4.7 5× 5 0.10 3 20 UMW1H4R7MDD 10 6.3× 5 0.10 5 33 UMW1H100MDD 22 8× 5 0.10 11 52 UMW1H220MDD 33 8× 5 0.10 16.5 71 UMW1H330MDD For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ). If there is no size code in the part number, please add size code “1” and then add the appropriate code. Please refer to page 18, 19 about the formed or taped product spec. Please refer to page 4 for the minimum order quantity. CAT.8100J