UTS1HR33MDD

ALUMINUM ELECTROLYTIC CAPACITORS TS Miniature Sized, High Reliability For Switching Power Supplies Approved by Reliability Center for Electronic Component, Japan-Certification No. RCJ-03-23C series Smaller case size and Long Life product. Compliant to the RoHS directive (2002/95/EC). Products which are scheduled to be discontinued. Not recommended for new designs PS TS Long Life Specifications ltem Performance Characteristics Category Temperature Range – 40 to +105˚C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 470µF Capacitance Tolerance ± 20% at 120Hz, 20˚C Leakage Current After 2 minutes' application of rated voltage, leakage current is less than 0.03CV or 3 (µA), whichever is greater. Measurement frequency : 120Hz at 20˚C Tangent of loss angle (tan δ) 6.3 0.30 Rated voltage (V) tan δ (MAX.) 10 0.28 16 0.24 25 0.18 35 0.16 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Stability at Low Temperature 6.3 5 10 10 4 8 16 3 6 The specifications listed at right shall be met when the capacitors are restored to 20˚C after the rated voltage is applied for 5000 hours at 105˚C. Endurance 25 2 4 35 2 3 50 2 3 Capacitance change Within ±30% of the initial capacitance value tan δ 300% or less than the initial specified value Leakage current Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105˚C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Marking Printed with white color letter on dark blown sleeve. Type numbering system (Example : 25V 100µF) Radial Lead Type φd Sleeve (P.E.T.) 1 2 3 4 5 6 7 8 9 10 11 P ± 0.5 φD+0.5 MAX. U T S 1 E 1 0 1 M PD Configuration Capacitance tolerance (± 20%) Rated capacitance (100µF) L+ MAX. 15MIN Rated voltage (25V) 4MIN Series name Pressure relief vent Type (φ8up) Configuration (mm) (L = 7) 1.0 (L 9) 1.5 φD 4 5 P 1.5 2.0 φd 0.45 6.3 2.5 0.5 0.45 (0.45) 8 3.5 0.6 φD Pb-free leadwire Pb-free PET sleeve 4 5 6.3 DD 8 PD ( ) : Applied to 7mmL products • Please refer to page 20 about the end seal configulation. Please refer to page 20, 21, 22 about the formed or taped product spec. Please refer to page 4 for the minimum order quantity. Dimension table in next page. CAT.8100B ALUMINUM ELECTROLYTIC CAPACITORS TS series Standard Ratings V (Code) Item Cap.(µF) Code 6.3 (0J) Case size φD × L (mm) 10 (1A) Rated ripple (mArms) 105˚C / 100kHz 10 100 22 220 33 330 47 470 5×7 65 100 101 6.3 × 7 100 220 221 6.3 × 9 150 330 331 8×9 210 470 471 8×9 210 4×7 Item Cap.(µF) Code (mArms) 105˚C / 100kHz 25 (1E) Rated ripple (mArms) 105˚C / 100kHz Case size φD × L (mm) Rated ripple (mArms) 105˚C / 100kHz 4×7 29 5×7 50 6.3 × 7 86 6.3 × 7 90 6.3 × 9 112 6.3 × 9 117 8×9 165 8×9 210 60 8×9 35 (1V) Case size φD × L (mm) Case size φD × L (mm) 40 5×7 V (Code) 16 (1C) Rated ripple Case size φD × L (mm) 195 50 (1H) Rated ripple (mArms) 105˚C / 100kHz Case size φD × L (mm) Rated ripple (mArms) 105˚C / 100kHz 0.1 0R1 4×7 3.3 0.22 R22 4×7 7.3 0.33 R33 4×7 0.47 R47 4×7 13 1 010 4×7 18 2.2 2R2 4×7 22 3.3 3R3 4×7 25 4.7 4R7 4×7 30 5×7 30 10 100 5×7 43 6.3 × 7 54 22 220 6.3 × 7 76 6.3 × 9 86 33 330 6.3 × 9 100 47 470 8×9 153 100 101 8×9 188 8.8 Frequency coefficient of rated ripple current Frequency 50Hz 120Hz 300Hz 1kHz 10kHz 100kHz or more 0.1 to 4.7 0.25 0.40 0.50 0.70 0.90 1.00 10 to 47 0.40 0.50 0.60 0.75 0.90 1.00 100 to 470 0.50 0.60 0.70 0.80 0.90 1.00 Cap. (µF) CAT.8100B