UTT0J220MDD1TP

ALUMINUM ELECTROLYTIC CAPACITORS UTT Miniature Sized, Low Impedance, High Reliability For Switching Power Supplies Approved Approved by Reliability by Reliability Center Center for Electronic for Electronic Component, Component, Japan-Certification Japan-Certification No. RCJ-03-23C No. RCJ-03-23C Smaller case size and Long Life product. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). UPW UTT Long Life Specifications ltem Performance Characteristics Category Temperature Range –40 to +105˚C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 470µF Capacitance Tolerance ± 20% at 120Hz, 20˚C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.03CV or 3 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C 10 0.28 6.3 0.30 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 16 0.24 25 0.18 35 0.16 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio (MAX.) Z– 40°C / Z+20°C Stability at Low Temperature 6.3 5 10 The specifications listed at right shall be met when the capacitors are restored to 20˚C after the rated voltage is applied for 5000 hours at 105˚C. Endurance 25 3 6 16 3 8 10 4 10 35 3 4 50 3 4 Capacitance change Within ±30% of the initial capacitance value 300% or less than the initial specified value tan δ Less than or equal to the initial specified value Leakage current After storing the capacitors under no load at 105˚C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Shelf Life Marking Printed with white color letter on dark blown sleeve. Radial Lead Type Type Type numbering numbering system system (Example (Example : 25V : 25V 100µF) 100µF) φd Sleeve (P.E.T.) 1 2 3 4 5 6 7 8 9 10 11 P±0.5 φD+0.5 MAX. U T T 1 E 1 0 1 M PD Configuration Capacitance tolerance ( ±20%) Rated capacitance (100μF) L+ MAX. Pressure relief vent (φ8up) 15MIN Rated voltage (25V) 4MIN Series name Type Configuration (mm) (L = 7) 1.0 (L 9) 1.5 φD 4 5 6.3 8 P 1.5 2.0 2.5 3.5 0.45 0.5 0.45 (0.45) φd φD Pb-free leadwire Pb-free PET sleeve 4 to 6.3 DD 8 PD 0.6 ( ) : Applied to 7mmL products • Please refer to page 18 about the end seal configuration. Frequency coefficient of rated ripple current Cap. (µF) Frequency 50Hz 120Hz 300Hz 1kHz 10kHz 100kHz or more 0.25 0.30 0.50 0.70 0.90 1.00 10 to 47 0.30 0.40 0.60 0.75 0.90 1.00 100 to 470 0.60 0.60 0.70 0.80 0.90 1.00 1 to 4.7 Dimension table in next page. CAT.8100J ALUMINUM ELECTROLYTIC CAPACITORS UTT ■ Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） 25 （1E） Rated Capacitance （µF） Leakage Current Rated Ripple Impedance（Ω） （µA） （mArms） MAX. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes （ ） Part Number 4× 7 0.30 4.158 7.40 46 UTT0J220MDD 47 5×7 0.30 8.883 4.00 74 UTT0J470MDD 100 6.3× 7 0.30 18.9 2.10 120 UTT0J101MDD 220 6.3× 9 0.30 41.58 1.10 163 UTT0J221MDD 330 8× 9 0.30 62.37 0.68 230 UTT0J331MPD 470 8× 9 0.30 88.83 0.68 230 UTT0J471MPD 33 5× 7 0.28 9.9 4.00 74 UTT1A330MDD 150 6.3× 9 0.28 45 1.10 163 UTT1A151MDD 220 8× 9 0.28 66 0.68 230 UTT1A221MPD 10 4× 7 0.24 4.8 7.40 46 UTT1C100MDD 22 5× 7 0.24 10.56 4.00 74 UTT1C220MDD 47 6.3× 7 0.24 22.56 2.10 120 UTT1C470MDD 100 6.3× 9 0.24 48 1.10 163 UTT1C101MDD 150 8× 9 0.24 72 0.68 230 UTT1C151MPD 220 8× 9 0.24 105.6 0.68 230 UTT1C221MPD 330 8× 9 0.24 158.4 0.68 230 UTT1C331MPD 470 8× 11.5 0.24 225.6 0.40 298 UTT1C471MPD 22 5× 7 0.18 16.5 4.00 74 UTT1E220MDD 33 6.3× 7 0.18 24.75 2.10 120 UTT1E330MDD 47 6.3× 9 0.18 35.25 1.10 163 UTT1E470MDD 100 8×9 0.18 75 0.68 230 UTT1E101MPD 220 8× 11.5 0.18 165 0.40 298 UTT1E221MPD 247.5 4.7 10 50 （1H） tan δ 22 330 35 （1V） Case Size φD×L（mm） 8× 11.5 0.18 4× 7 0.16 5× 7 0.16 4.935 10.5 0.40 298 UTT1E331MPD 7.40 37 UTT1V4R7MDD 4.00 74 UTT1V100MDD 22 6.3× 7 0.16 23.1 2.10 120 UTT1V220MDD 33 6.3× 9 0.16 34.65 1.10 163 UTT1V330MDD 47 6.3×9 0.16 49.35 1.10 163 UTT1V470MDD 1 4× 7 0.14 3 30.00 23 UTT1H010MDD 2.2 4× 7 0.14 3.3 23.00 26 UTT1H2R2MDD 3.3 4× 7 0.14 4.95 20.00 29 UTT1H3R3MDD 4.7 5× 7 0.14 7.05 14.00 37 UTT1H4R7MDD 10 6.3× 7 0.14 4.40 84 UTT1H100MDD 22 6.3× 9 0.14 33 2.40 112 UTT1H220MDD 47 8× 9 0.14 70.5 1.40 162 UTT1H470MPD 15 For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ). If there is no size code in the part number, please add size code “1” and then add the appropriate code. Please refer to page 18, 19 about the formed or taped product spec. Please refer to page 4 for the minimum order quantity. CAT.8100J