UUB1H470MNL1GS

ALUMINUM ELECTROLYTIC CAPACITORS UUB Chip Type, High Reliability (Through 50V only) Chip type, high temperature range, for +125°C use. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. ULT High Temperature High Voltage Reflow Added ESR specification at –40°C UCJ Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance UWH UUB High Temperature UUX Performance Characteristics –40 to +125°C 10 to 400V 1 to 330µF ± 20% at 120Hz, 20°C Leakage Current Rated voltage (V) 10 to 50 160 to 400 Leakage Current After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV (µA). I = 0.04CV+100 ( µA) max.(1 minute's at 20°C) Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 10 0.32 16 0.24 25 0.21 35 0.18 50 0.18 160 0.30 200 0.30 250 0.30 400 0.30 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio Z–40°C / Z+20°C ZT / Z20 (MAX.) 10 16 25 35 50 160 200 250 400 12 8 6 4 4 8 8 8 12 The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours (1000 hours for φ8 × 6.2) at 125°C. Endurance Resistance to soldering heat Marking Chip Type Type numbering system (Example : 10V 100µF) (φ8 × 6.2) L±0.3 H L±0.5 7 8 9 10 11 12 13 14 Configuration Code CL NL NL Series name Type Negative Pressure relief vent 6 (mm) A±0.2 E A±0.2 B±0.2 φD±0.5 Voltage 5 φD × L Rated capacitance (100µF) 8 × 6.2 8 × 10 Rated voltage (10V) 10 × 10 Positive C±0.2 0.3MAX. 4 Capacitance tolerance (±20%) Negative Plastic platform Capacitance A2E 330 10V 0.5MAX. H 3 Taping code 0.5MAX. (φ8 × 10, φ10) 2 UUB 1 A 1 0 1 MC L 1 GS A±0.2 E A±0.2 B±0.2 φD±0.5 A2E 100 10V C±0.2 0.3MAX. Voltage Capacitance Lot No. 1 Positive Plastic platform 125˚C Marking 125˚C Marking Lot No. Trade mark Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C. The capacitors shall meet Less than or equal to the initial specified value tan δ the characteristic requirements listed at right when they Less than or equal to the initial specified value Leakage current are removed from the plate and restored to 20°C. Black print on the case top. Shelf Life Trade mark Capacitance change tan δ Leakage current φD × L A B C E L H 8 × 6.2 8 × 10 3.3 2.9 8.3 8.3 8.3 8.3 3.1 2.3 6.2 10 0.5 to 0.8 0.8 to 1.1 10 × 10 3.2 10.3 10.3 4.5 10 0.8 to 1.1 Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UUB ■ Dimensions Rated Voltage （V） （code） 10 （1A） 16 （1C） 25 （1E） 35 （1V） 50 （1H） 160 （2C） 200 （2D） Rated Capacitance （µF） Case Size φD×L（mm） tan δ 100 8×6.2 0.32 400 （2G） （ ） 30 Rated Ripple （mArms） （125℃/120Hz） Part Number 58 UUB1A101MCL1GS 220 8× 10 0.32 66 90 UUB1A221MNL1GS 330 10× 10 0.32 99 112 UUB1A331MNL1GS 100 8×10 0.24 48 66 UUB1C101MNL1GS 220 10× 10 0.24 105.6 102 UUB1C221MNL1GS 47 8× 6.2 0.21 48 UUB1E470MCL1GS 35.25 100 8× 10 0.21 75 74 UUB1E101MNL1GS 220 10× 10 0.21 165 116 UUB1E221MNL1GS 33 8× 6.2 0.18 44 UUB1V330MCL1GS 47 8×10 0.18 100 10× 10 0.18 34.65 49.35 105 52 UUB1V470MNL1GS 80 UUB1V101MNL1GS 10 8× 6.2 0.18 15 24 UUB1H100MCL1GS 22 8×6.2 0.18 33 38 UUB1H220MCL1GS 33 8× 10 0.18 49.5 46 UUB1H330MNL1GS 47 10 ×10 0.18 70.5 58 UUB1H470MNL1GS 8×10 0.30 143.52 42 UUB2C6R8MNL1GS 6.8 10 10 ×10 0.30 164 59 UUB2C100MNL1GS 4.7 8×10 0.30 137.6 36 UUB2D4R7MNL1GS 6.8 10×10 0.30 154.4 59 UUB2D6R8MNL1GS 10 250 （2E） Leakage Current （µA） at 20℃ after 1 minute 10× 10 0.30 180 59 UUB2D100MNL1GS 3.3 8× 10 0.30 133 28 UUB2E3R3MNL1GS 4.7 10 ×10 0.30 147 59 UUB2E4R7MNL1GS 1 8× 10 0.30 116 26 UUB2G010MNL1GS 1.8 8×10 0.30 128.8 27 UUB2G1R8MNL1GS 2.2 10 ×10 0.30 135.2 36 UUB2G2R2MNL1GS 3.3 10 ×10 0.30 152.8 38 UUB2G3R3MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K