UUD0J270MCL1GS

ALUMINUM ELECTROLYTIC CAPACITORS UUD Chip Type, Low Impedance Chip type, low impedance temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UWD High Temp reflow UCD UUD Low Impedance UWG Low Impedance Specifications Performance Characteristics Item Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C Rated voltage (V) 6.3 10 16 25 35 50 tan δ (MAX.) 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) Tangent of loss angle (tan δ) ( ) is φ8 over Measurement frequency : 120Hz 6.3 3 5 Rated voltage (V) Z– 25°C / Z+20°C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Z– 55°C / Z+20°C 10 2 4 The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours (2000 hours for φD = 4, 5 and 6.3) at 105°C. Endurance 50 2 3 35 2 3 25 2 3 16 2 4 Capacitance change tan δ Leakage current Within ±30% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan δ requirements listed at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Chip Type Type numbering system (Example : 16V 22µF) (φ4 to φ6.3) Positive 2 3 4 5 6 7 8 9 10 11 12 13 14 Taping code A±0.2 E A±0.2 B±0.2 φD±0.5 H L±0.3 Capacitance Lot No. C±0.2 0.3 MAX. Series A2 22C UD Voltage (C:16V) 1 UUD 1 C 2 2 0 M C L 1 GS 0.5 MAX. Plastic platform Configuration Capacitance tolerance (±20%) Rated capacitance (22µF) Negative φD 4 to 6.3 8 • 10 Code CL NL Rated voltage (16V) Series name Type (φ8,φ10 ) Lot No. H L±0.5 Capacitance (mm) φD×L A±0.2 E A±0.2 C±0.2 B±0.2 A2 100V UD Trade mark Plastic platform 0.3 MAX. Series φD±0.5 Voltage (V:35V) 0.5 MAX. Positive Negative A B C E L H 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 10 10 × 10 1.8 4.3 4.3 1.0 5.8 0.5 to 0.8 2.1 5.3 5.3 1.3 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 7.7 0.5 to 0.8 2.9 8.3 8.3 3.1 10 0.8 to 1.1 3.2 10.3 10.3 4.5 10 0.8 to 1.1 Pressure relief vent Voltage V 6.3 j Code Frequency coefficient of rated ripple current 10 A 16 C 25 E 35 V 50 H Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UUD Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） Rated Capacitance （µF） Leakage Current Rated Ripple Impedance（Ω） （µA） （mArms） MAX. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes Case Size φD×L（mm） tan δ 27 4×5.8 0.26 3 1.80 80 UUD0J270MCL1GS 33 5× 5.8 0.26 3 0.76 150 UUD0J330MCL1GS 47 5× 5.8 0.26 3 0.76 150 UUD0J470MCL1GS 56 5× 5.8 0.26 3.528 0.76 150 UUD0J560MCL1GS （ ） Part Number 68 6.3× 5.8 0.26 4.284 0.44 230 UUD0J680MCL1GS 100 6.3×5.8 0.26 6.3 0.44 230 UUD0J101MCL1GS 150 6.3×5.8 0.26 9.45 0.44 230 UUD0J151MCL1GS 220 6.3×5.8 0.26 13.86 0.44 230 UUD0J221MCL1GS 330 6.3×7.7 0.26 20.79 0.34 280 UUD0J331MCL1GS 470 8×10 0.28 29.61 0.17 450 UUD0J471MNL1GS 680 8×10 0.28 42.84 0.17 450 UUD0J681MNL1GS 1000 8×10 0.28 63 0.17 450 UUD0J102MNL1GS 1500 10× 10 0.28 94.5 0.09 670 UUD0J152MNL1GS 22 4×5.8 0.20 3 1.80 80 UUD1A220MCL1GS 27 5×5.8 0.20 3 0.76 150 UUD1A270MCL1GS 33 5×5.8 0.20 3.3 0.76 150 UUD1A330MCL1GS 47 6.3×5.8 0.20 4.7 0.44 230 UUD1A470MCL1GS 56 6.3×5.8 0.20 5.6 0.44 230 UUD1A560MCL1GS 68 6.3×5.8 0.20 6.8 0.44 230 UUD1A680MCL1GS 100 6.3× 5.8 0.20 10 0.44 230 UUD1A101MCL1GS 150 6.3× 5.8 0.20 15 0.44 230 UUD1A151MCL1GS 220 6.3× 7.7 0.20 22 0.34 280 UUD1A221MCL1GS 330 8×10 0.24 33 0.17 450 UUD1A331MNL1GS 470 8× 10 0.24 47 0.17 450 UUD1A471MNL1GS 680 10 ×10 0.24 68 0.09 670 UUD1A681MNL1GS 1000 10 ×10 0.24 100 0.09 670 UUD1A102MNL1GS 15 4× 5.8 0.16 3 1.80 80 UUD1C150MCL1GS 22 5× 5.8 0.16 3.52 0.76 150 UUD1C220MCL1GS 27 5× 5.8 0.16 4.32 0.76 150 UUD1C270MCL1GS 33 6.3× 5.8 0.16 5.28 0.44 230 UUD1C330MCL1GS 47 6.3× 5.8 0.16 7.52 0.44 230 UUD1C470MCL1GS 56 6.3× 5.8 0.16 8.96 0.44 230 UUD1C560MCL1GS 68 6.3× 5.8 0.16 10.88 0.44 230 UUD1C680MCL1GS 100 6.3×5.8 0.16 16 0.44 230 UUD1C101MCL1GS 150 6.3×7.7 0.16 24 0.34 280 UUD1C151MCL1GS 220 6.3×7.7 0.16 35.2 0.34 280 UUD1C221MCL1GS 330 8× 10 0.20 52.8 0.17 450 UUD1C331MNL1GS 470 8×10 0.20 75.2 0.17 450 UUD1C471MNL1GS 680 10× 10 0.20 108.8 0.09 670 UUD1C681MNL1GS CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UUD Dimensions Rated Voltage （V） （code） 25 （1E） Rated Capacitance （µF） Case Size φD×L（mm） tan δ 10 4×5.8 0.14 50 （1H） （ ） 3 1.80 80 Part Number UUD1E100MCL1GS 15 5× 5.8 0.14 3.75 0.76 150 UUD1E150MCL1GS 22 5× 5.8 0.14 5.5 0.76 150 UUD1E220MCL1GS 27 6.3×5.8 0.14 6.75 0.44 230 UUD1E270MCL1GS 33 6.3×5.8 0.14 8.25 0.44 230 UUD1E330MCL1GS 47 6.3×5.8 0.14 11.75 0.44 230 UUD1E470MCL1GS 56 6.3×5.8 0.14 14 0.44 230 UUD1E560MCL1GS 68 6.3×5.8 0.14 17 0.44 230 UUD1E680MCL1GS 100 6.3×7.7 0.14 25 0.34 280 UUD1E101MCL1GS 150 8×10 0.16 37.5 0.17 450 UUD1E151MNL1GS 220 8×10 0.16 55 0.17 450 UUD1E221MNL1GS 330 8×10 0.16 82.5 0.17 450 UUD1E331MNL1GS 470 10×10 0.16 117.5 0.09 670 UUD1E471MNL1GS 4×5.8 0.12 3 1.80 80 UUD1V4R7MCL1GS 4.7 35 （1V） Leakage Current Rated Ripple Impedance（Ω） （µA） （mArms） MAX. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes 10 5×5.8 0.12 3.5 0.76 150 UUD1V100MCL1GS 15 5×5.8 0.12 5.25 0.76 150 UUD1V150MCL1GS 22 5×5.8 0.12 7.7 0.76 150 UUD1V220MCL1GS 27 6.3×5.8 0.12 9.45 0.44 230 UUD1V270MCL1GS 33 6.3×5.8 0.12 11.55 0.44 230 UUD1V330MCL1GS 47 6.3×5.8 0.12 16.45 0.44 230 UUD1V470MCL1GS 56 6.3×7.7 0.12 19.6 0.34 280 UUD1V560MCL1GS 68 6.3×7.7 0.12 23.8 0.34 280 UUD1V680MCL1GS 100 8×10 0.14 35 0.17 450 UUD1V101MNL1GS 150 8×10 0.14 52.5 0.17 450 UUD1V151MNL1GS 220 8×10 0.14 77 0.17 450 UUD1V221MNL1GS 330 10 ×10 0.14 115.5 0.09 670 UUD1V331MNL1GS 1 4× 5.8 0.12 3 5.00 30 UUD1H010MCL1GS 2.2 4× 5.8 0.12 3 5.00 30 UUD1H2R2MCL1GS 3.3 4× 5.8 0.12 3 5.00 30 UUD1H3R3MCL1GS 4.7 5× 5.8 0.12 3 1.52 85 UUD1H4R7MCL1GS 10 6.3×5.8 0.12 5 0.88 165 UUD1H100MCL1GS 15 6.3×5.8 0.12 7.5 0.88 165 UUD1H150MCL1GS 22 6.3×5.8 0.12 11 0.88 165 UUD1H220MCL1GS 27 6.3×7.7 0.12 13.5 0.68 185 UUD1H270MCL1GS 33 6.3×7.7 0.12 16.5 0.68 185 UUD1H330MCL1GS 47 6.3×7.7 0.12 23.5 0.68 185 UUD1H470MCL1GS 56 8× 10 0.14 28 0.34 300 UUD1H560MNL1GS 68 8×10 0.14 34 0.34 300 UUD1H680MNL1GS 100 8× 10 0.14 50 0.34 300 UUD1H101MNL1GS 150 10× 10 0.14 75 0.18 670 UUD1H151MNL1GS 220 10× 10 0.14 110 0.18 670 UUD1H221MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K