UUH1A222MNL

ALUMINUM ELECTROLYTIC CAPACITORS UH Chip Type, High Reliability, Higher Capacitance Range series Chip Type, higher capacitance in larger case sizes (φ12.5, φ16, φ18, φ20) Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape and tray. Adapted to the RoHS directive (2002/95/EC). UH High Temperature Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ UJ Performance Characteristics – 55 ~ +125°C 10 ~ 50V 100 ~ 3300µF ± 20% at 120Hz, 20°C After 1 minutes' application of rated voltage, leakage current is not more than 0.03CV or 4 (µA), whichever is greater. Rated voltage (V) tan δ (MAX) Rated voltage (V) 10 0.22 16 0.18 25 0.16 35 0.14 50 0.12 120Hz 20°C For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. 10 4 8 16 3 6 25 2 4 35 2 3 50 2 3 Within ±30% of initial value 300% or less of initial specified value Initial specified value or less 120Hz Stability at Low Temperature Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) Z–40°C / Z+20°C Endurance After 5000 hours' application of rated voltage at 125°C, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Shelf Life Marking After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. Black print on the case top. Chip Type Trade mark Voltage Lot No. nichicon A±0.2 Plastic platform B±0.2 Type numbering system (Example : 50V 330µF) UUH 1 H 3 3 1 M NL 1 MS C±0.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Package code Taping MS Tray ZD Configuration Code BD 12.5~18 NL RL 20 330 µF UH 50V H0536 D±0.5 B±0.2 B E Series Capacitance B D A B C E H 12.5 4.0 13.6 16.0 8.0 2.5 10 1A 16. 4.5 17.1 19.5 10.5 3.75 18. 5.0 19.1 21.5 11.5 3.75 (mm) 20. 5.0 21.1 23.5 13.5 3.75 H±0.1 The lead terminal structure : The same bent lead type (refer to p.60) that is currently used on 10mm diameter and smaller parts, is also available upon request. In this case of the bent lead type, Q will be put at the 11th digit of type numbering system. Please ask for details. 16 1C 25 1E Dimensions (µF) Cap. V Code A±0.2 Pressure relief vent Size code L±0.5 Capacitance Tolerance (± 20%) Rated Capacitance (330µF) Rated voltage (50V) Series name Type 35 1V 12.5 × 13.5 100 220 330 470 1000 2200 3300 101 221 331 471 102 222 332 12.5 × 13.5 12.5 × 16.5 18 × 16.5 16 × 21.5 18 × 21.5 230 350 620 620 770 12.5 × 13.5 12.5 × 13.5 16 × 16.5 18 × 21.5 210 250 440 710 12.5 × 13.5 16 × 16.5 18 × 21.5 20 × 16.5 230 310 540 540 200 280 380 380 610 50 1H 12.5 × 13.5 16 × 16.5 16 × 21.5 18 × 16.5 18 × 21.5 170 250 340 340 430 16 × 16.5 18 × 16.5 16 × 21.5 20 × 21.5 Case size φ D × L (mm) Rated Ripple In this case, 6 will be put at 12th digit of type numbering system, " " Rated Ripple (mArms) at 125°C 120Hz Frequency coefficient of rated ripple current Cap.(µF) Frequency 0100 ~ 4700 1000 ~ 3300 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.23 1.10 1 kHz 1.34 1.13 10 kHz~ 1.50 1.15 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V