UUK1V101MCO

ALUMINUM ELECTROLYTIC CAPACITORS UK 6mmL Chip Type, For general Audio Equipment series Chip type acoustic series. Applicable to automatic insertion machine using carrier tape. Adapted to the RoHS directive (2002/95/EC) UK Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current Chip MW Performance Characteristics – 40 ~ +85°C 4 ~ 50V 0.1 ~ 220µF ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.) tan δ 4 0.35 6.3 0.26 4 7 15 10 0.20 6.3 4 8 16 0.16 10 3 8 25 0.14 16 2 4 25 2 4 35 0.12 35 2 3 50 0.12 50 2 3 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Endurance After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristics requirements listed at right. Capacitance change tan δ Leakage current Within ± 20% of initial value 200% or less of initial specified value Initial specified value or less Shelf Life Resistance to soldering heat Marking After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristics requirements Initial specified value or less Leakage current listed at right. Black print on the case top. Chip Type Capacitance Lot No. ∗Voltage Plastic platform 0.3MAX. 0.5MAX. Positive Type numbering system (Example : 16V 10µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 U U K 1 C 1 0 0 MCO 1 G S (mm) φD C±0.2 Taping code Size code Configuration Rated Capacitance tolerance ( ± 20%) Capacitance (10µF ) Rated voltage (16V ) Series name Type L ± 0.3 0.5 ~ 0.8 ∗Voltage mark for 6.3V is 6V . A B C E L 4 1.8 4.3 4.3 1.0 5.8 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 5.8 5.8 Negative Dimensions V Cap.(µF) Code 4 0G 6.3 0J A±0.2 A±0.2 X2 10 16V φD±0.5 B ± 0.2 E 10 1A 16 1C 25 1E 35 1V 4 4 4 4 4 4 4 5 6.3 50 1H 1.0 2.0 2.8 4.0 8.4 13 17 20 33 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 221 4 4 5 6.3 28 33 56 96 4 5 5 6.3 28 37 45 70 5 5 6.3 33 41 52 4 5 6.3 6.3 23 37 49 58 4 5 6.3 6.3 16 27 42 52 4 5 6.3 18 29 46 Case size φ D Rated ripple Rated Ripple(mArms)at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V