UUL1A330MCL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UUL Chip Type,  Long Life Assurance Chip type with load life of 5000 hours at +105°C. Designed for surface mounting on high density PC board. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UCB UUL Long Life UUA Long Life Specifications Item Performance Characteristics Category Temperature Range –40 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 1000µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01 CV or 3 (µA), Max Measurement frequency : 120Hz at 20°C Rated voltage (V) tan δ (max.) Tangent of loss angle (tan δ) 6.3 0.32 10 0.24 16 0.20 25 0.16 35 0.13 50 0.12 Measurement frequency : 120Hz 6.3 4 10 Rated voltage (V) Z(– 25°C) / Z(+20°C) Impedance ratio ZT / Z20 (max.) Z(– 40°C) / Z(+20°C) Stability at Low Temperature The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours at 105°C. Endurance 10 3 7 50 2 3 35 2 3 25 2 3 16 2 5 Within ±30% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan δ requirements listed at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Chip Type Type numbering system (Example : 16V 100µF) (φ4 to φ6.3) Positive Plastic platform 0.5 max. H L±0.3 Capacitance Lot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UU L 1 C 1 0 1 M C L 1 GS A±0.2 E A±0.2 B±0.2 φD±0.5 A2 10C UL Voltage (C : 16V) C±0.2 0.3 max. Series Taping code Configuration Capacitance tolerance (±20%) Rated capacitance (100µF) Negative Rated voltage (16V) φD 4 to 6.3 8 • 10 Code CL NL Series name Type (φ8,φ10 ) Lot No. H L±0.5 Capacitance Pressure relief vent Voltage V 6.3 Code j 10 A 16 C C±0.2 25 E 35 V 50 H (mm) A±0.2 E A±0.2 φD±0.5 A2 100V UL Trade mark Plastic platform 0.3 max. Series B±0.2 Voltage (V : 35V) 0.5 max. Positive Negative φD×L 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 10 A 1.8 2.1 2.4 2.4 2.9 10 × 10 3.2 B 4.3 5.3 6.6 6.6 8.3 10.3 C 4.3 5.3 6.6 6.6 8.3 10.3 E 1.0 1.3 2.2 2.2 3.1 4.5 L 5.8 5.8 5.8 7.7 10 10 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Dimension table in next page. CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UUL Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） 25 （1E） Rated Capacitance （µF） Leakage Current （µA） at 20℃ after 2 minutes （ ） Rated Ripple （mArms） （105℃/120Hz） Part Number 33 5×5.8 0.32 3 35 UUL0J330MCL1GS 5× 5.8 0.32 3 36 UUL0J470MCL1GS 100 6.3×5.8 0.32 6.3 60 UUL0J101MCL1GS 220 6.3×7.7 0.32 13.86 101 UUL0J221MCL1GS 330 8×10 0.32 20.79 160 UUL0J331MNL1GS 470 10 ×10 0.32 29.61 254 UUL0J471MNL1GS 1000 10× 10 0.32 63 313 UUL0J102MNL1GS 22 5× 5.8 0.24 3 30 UUL1A220MCL1GS 33 5×5.8 0.24 3.3 35 UUL1A330MCL1GS 47 6.3×5.8 0.24 4.7 50 UUL1A470MCL1GS 100 6.3× 7.7 0.24 81 UUL1A101MCL1GS 10 220 8× 10 0.24 22 141 UUL1A221MNL1GS 330 10× 10 0.24 33 238 UUL1A331MNL1GS 470 10× 10 0.24 47 254 UUL1A471MNL1GS 10 4× 5.8 0.20 3 18 UUL1C100MCL1GS 22 5×5.8 0.20 3.52 30 UUL1C220MCL1GS 33 6.3×5.8 0.20 5.28 48 UUL1C330MCL1GS 47 6.3×5.8 0.20 100 6.3×7.7 0.20 16 220 10× 10 0.20 35.2 7.52 50 UUL1C470MCL1GS 81 UUL1C101MCL1GS 216 UUL1C221MNL1GS 330 10×10 0.20 52.8 238 UUL1C331MNL1GS 470 10×10 0.20 75.2 254 UUL1C471MNL1GS 10 5×5.8 0.16 3 25 UUL1E100MCL1GS 22 6.3× 5.8 0.16 5.5 42 UUL1E220MCL1GS 33 6.3× 5.8 0.16 8.25 48 UUL1E330MCL1GS 47 6.3× 7.7 0.16 11.75 63 UUL1E470MCL1GS 100 8×10 0.16 25 116 UUL1E101MNL1GS 220 10 ×10 0.16 55 216 UUL1E221MNL1GS 330 10 ×10 0.16 82.5 238 UUL1E331MNL1GS 4×5.8 0.13 3 15 UUL1V4R7MCL1GS 10 5×5.8 0.13 3.5 25 UUL1V100MCL1GS 22 6.3×5.8 0.13 7.7 42 UUL1V220MCL1GS 33 6.3×7.7 0.13 11.55 57 UUL1V330MCL1GS 47 8×10 0.13 16.45 92 UUL1V470MNL1GS 100 10× 10 0.13 35 151 UUL1V101MNL1GS 220 10× 10 0.13 77 216 UUL1V221MNL1GS 1 4×5.8 0.12 3 2.2 4× 5.8 0.12 3 11 UUL1H2R2MCL1GS 3.3 4× 5.8 0.12 3 14 UUL1H3R3MCL1GS 4.7 50 （1H） tan δ 47 4.7 35 （1V） Case Size φD×L（mm） 6.2 UUL1H010MCL1GS 5× 5.8 0.12 3 19 UUL1H4R7MCL1GS 10 6.3× 5.8 0.12 5 30 UUL1H100MCL1GS 22 6.3× 7.7 0.12 11 49 UUL1H220MCL1GS 33 8× 10 0.12 16.5 77 UUL1H330MNL1GS 47 8× 10 0.12 23.5 92 UUL1H470MNL1GS 100 10 ×10 0.12 50 151 UUL1H101MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100L