UUN2A332MNL

ALUMINUM ELECTROLYTIC CAPACITORS UN Chip Type, Bi-Polarized, Higher Capacitance Range series Chip Type ,higher capacitance in larger case sizes (φ12.5, φ 16, φ 18, φ 20) Designed for surface mounting on high density PC board. Bi-polarized series for operations over wide temperature range of – 55 ~ +105°C. Applicable to automatic mounting machine using carrier tape and tray. Adapted to the RoHS directive (2002/95/EC). UN Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Bi-polarized UJ Performance Characteristics – 55 ~ +105°C 6.3 ~ 100V 22 ~ 3300µF ± 20% at 120Hz, 20°C After 1 minutes' application of rated voltage, leakage current is not more than 0.03CV or 4 (µA), whichever is greater. Rated voltage (V) tan δ (MAX) 6.3 0.26 10 0.22 16 0.18 25 0.16 35 0.14 50 0.12 63 0.10 100 0.09 120Hz 20°C For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. Rated voltage (V) Stability at Low Temperature Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) 6.3 5 10 10 4 8 16 3 6 25 2 4 35 2 3 50 2 3 63 2 3 100 2 3 120Hz Z–40°C / Z+20°C Endurance After 2000 hours' application of rated voltage at 105°C with the polarity inverted every 250 hours, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Within ±20% of initial value 200% or less of initial specified value Initial specified value or less Shelf Life Marking After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. Black print on the case top. Chip Type Trade mark Voltage Lot No. Plastic platform A±0.2 B±0.2 Type numbering system (Example : 50V 330µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UUN 1H 3 3 1 MNL 1 MS nichicon 330 µF H0536 50V Package code B D±0.5 B±0.2 C±0.2 E UN Taping Tray Size code MS ZD BP Capacitance L±0.5 H±0.1 A±0.2 Series Pressure relief vent Configuration Capacitance Tolerance(±20%) Rated Capacitance(330µF) Rated voltage(50V) φD 12.5 ~ 18 20 Code NL RL (mm) BD A B C E 12.5 4.0 13.6 16.0 8.0 2.5 16. 4.5 17.1 19.5 10.5 3.75 18. 5.0 19.1 21.5 11.5 3.75 20. 5.0 21.1 23.5 13.5 3.75 The lead terminal structure : The same bent lead type (refer to p.60) that is currently used on 10mm diameter and smaller parts, is also available upon request. In this case of the bent lead type, Q Please ask for details. will be put at the 11th digit of type numbering system. Series name Type Dimensions (µF) Cap. Code H V 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 63 1J 100 2A 12.5 × 13.5 12.5 × 16 100 150 180 310 22 33 47 100 220 330 470 1000 2200 3300 220 330 470 101 221 331 471 102 222 332 12.5 × 13.5 12.5 × 16 18 × 16.5 16 × 21.5 18 × 21.5 270 500 740 740 920 12.5 × 13.5 16 × 16.5 18 × 21.5 340 600 830 12.5 × 13.5 16 × 16.5 18 × 16.5 16 × 21.5 310 420 670 670 12.5 × 13.5 16 × 16.5 16 × 16.5 18 × 21.5 270 370 490 780 12.5 × 13.5 16 × 16.5 18 × 16.5 16 × 21.5 18 × 21.5 180 330 450 450 590 12.5 × 13.5 12.5 × 16 18 × 16.5 16 × 21.5 18 × 21.5 20 × 21.5 130 230 400 400 540 640 12.5 × 13.5 16 × 16.5 18 × 21.5 20 × 21.5 140 270 440 590 16 × 16.5 18 × 21.5 Case size φ D × L (mm) Rated Ripple In this case, 6 will be put at 12th digit of type numbering system, " " Rated Ripple (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Cap.(µF) Frequency 00 ~ 470 100 ~ 470 1000 ~ 3300 50 Hz 0.75 0.80 0.85 120 Hz 1.00 1.00 1.00 300 Hz 1.35 1.23 1.10 1 kHz 1.57 1.34 1.13 10 kHz~ 2.00 1.50 1.15 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V