UUP1H010MCL1GS

ALUMINUM ELECTROLYTIC CAPACITORS UUP 6mmL Chip Type, Bi-Polarized Chip type, bi-polarized withstanding high temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). UUN Extended range AEC-Q200 compliant. Please contact us for details. UUP High Temperature UWP Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 47µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.24 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.20 16 0.17 25 0.17 35 0.15 50 0.15 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C Shelf Life Resistance to soldering heat Marking Chip Type Type numbering system (Example : 16V 10µF) 1 105˚C Marking B±0.2 5.8±0.3 0.5 to 0.8 3 4 5 6 7 8 9 10 11 12 13 14 Taping code A±0.2 E A±0.2 C±0.2 0.3 MAX. φD±0.5 Voltage 2 UUP 1 C 1 0 0 M C L1 GS 0.5 MAX. Plastic platform Capacitance A2P 10 16V 50 2 3 The specifications listed at right shall be met Within ±20% of the initial capacitance value Capacitance change when the capacitors are restored to 20°C after tan δ 200% or less than the initial specified value the rated voltage is applied for 1000 hours at Less than or equal to the initial specified value Leakage current 105°C with the polarity every 250 hours. After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan δ requirements listed at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20°C. Black print on the case top. Endurance Lot No. 35 2 3 25 2 4 16 2 4 10 3 6 6.3 4 8 φD A B C E 4 1.8 4.3 4.3 1.0 (mm) 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 Configuration Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) Series name Type Voltage mark for 6.3V is 6V Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50　　 Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UUP Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 22 6.3 （0J） 10 （1A） ） 10 Part Number 28 UUP0J220MCL1GS 6.3× 5.8 0.24 10.395 37 UUP0J330MCL1GS 0.24 14.805 45 UUP0J470MCL1GS 10 4× 5.8 0.20 10 17 UUP1A100MCL1GS 22 6.3× 5.8 0.20 11 33 UUP1A220MCL1GS 33 6.3× 5.8 0.20 16.5 41 UUP1A330MCL1GS 4× 5.8 0.17 10 12 UUP1C4R7MCL1GS 10 5×5.8 0.17 10 23 UUP1C100MCL1GS 22 6.3× 5.8 0.17 17.6 37 UUP1C220MCL1GS 33 6.3× 5.8 0.17 26.4 49 UUP1C330MCL1GS 5× 5.8 0.17 10 12 UUP1E3R3MCL1GS 4.7 2.2 5× 5.8 0.17 10 16 UUP1E4R7MCL1GS 6.3× 5.8 0.17 12.5 27 UUP1E100MCL1GS 4× 5.8 0.15 10 8.4 UUP1V2R2MCL1GS 3.3 5× 5.8 0.15 10 16 UUP1V3R3MCL1GS 4.7 5× 5.8 0.15 10 18 UUP1V4R7MCL1GS 29 UUP1V100MCL1GS 10 50 （1H） 0.24 （ Rated Ripple （mArms） （105℃/120Hz） 6.3× 5.8 10 35 （1V） 5× 5.8 Leakage Current （µA） at 20℃ after 2 minutes 33 3.3 25 （1E） tan δ 47 4.7 16 （1C） Case Size φD×L（mm） 6.3× 5.8 0.15 17.5 0.1 4× 5.8 0.15 10 1.0 UUP1H0R1MCL1GS 0.22 4× 5.8 0.15 10 2.0 UUP1HR22MCL1GS 0.33 4× 5.8 0.15 10 2.8 UUP1HR33MCL1GS 0.47 4× 5.8 0.15 10 4.0 UUP1HR47MCL1GS 1 4× 5.8 0.15 10 8.4 UUP1H010MCL1GS 2.2 5× 5.8 0.15 10 13 UUP1H2R2MCL1GS 3.3 5× 5.8 0.15 10 17 UUP1H3R3MCL1GS 4.7 6.3× 5.8 0.15 11.75 20 UUP1H4R7MCL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. Please select UUN if high C/V products are required. CAT.8100K