UUR0G151MNL

ALUMINUM ELECTROLYTIC CAPACITORS UR Chip Type, High CV series Chip type, higher capacitance in larger case sizes. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WS High Temperature Reflow UG Extended range UR Higher C/V Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ WX Performance Characteristics – 40 ~ +85°C 4 ~ 100V 3.3 ~ 1500µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA) . Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.) 4 0.35 6.3 0.28 4 7 15 10 0.24 6.3 5 10 16 0.20 10 4 8 25 0.16 16 3 6 25 2 4 35 0.14 35 2 3 50 0.12 50 2 3 63 0.12 63 2 3 100 0.12 100 2 3 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Endurance After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Within ±20% of initial value 200% or less of initial specified value Initial specified value or less Shelf Life After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C, for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. Black print on the case top. Capacitance change tan δ Leakage current Resistance to soldering heat Marking Within ±10% of initial value Initial specified value or less Initial specified value or less Chip Type (φ6.3, φ8 × 6.2) Capacitance Lot No. φD±0.5 1 Trade mark B±0.2 Plastic platform 0.3MAX. 2Voltage C±0.2 Positive 0.5MAX. Type numbering system (Example : 10V 100µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UUR 1 A 1 0 1 M C L 1GS Package code A±0.2 Size code Configuration Capacitance tolerance (±20%) Rated Capacitance (100µF) Rated voltage (10V) Series name Type N2 100 10V L±0.3 H 1 Size φ8 × 6.2 only 2 Voltage mark for 6.3V is 6V . In case of marking for φ3 units, "V" for rated voltage is omitted. Negative φD×L 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 E Code A±0.2 CL CL CL NL NL (φ8 × 10, φ10 × 10) Positive Lot No. Trade mark C±0.2 0.5MAX. Plastic platform 0.3MAX. Capacitance 2 Voltage φD±0.5 B±0.2 φD×L (mm) 6.3 × 5.8 2.4 6.6 6.6 2.2 5.8 0.5 ~ 0.8 6.3 × 7.7 2.4 6.6 6.6 2.2 7.7 0.5 ~ 0.8 8 × 6.2 3.3 8.3 8.3 2.3 6.2 0.5 ~ 0.8 8 × 10 2.9 8.3 8.3 3.1 10 0.8 ~ 1.1 10 × 10 3.2 10.3 10.3 4.5 10 0.8 ~ 1.1 L±0.5 Pressure relief vent Negative H Dimension table in next page. A±0.2 A B C E L H N2 100 35V E A±0.2 CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS UR Cap.( F) 3.3 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 series Dimensions V Code 3R3 4R7 100 220 330 470 101 151 221 331 471 681 102 152 6.3 × 5.8 6.3 × 7.7 8 × 10. 8 × 10. 10 × 10. 152 200 284 344 347 8 × 6.2 160 (143) 8 × 6.2 190 (188) 8 × 10. 8 × 10. 265 6.3 × 5.8 6.3 × 5.8 8 × 10. 8 × 10. 70 85 240 290 374 454 8 × 6.2 6.3 × 7.7 125 151 6.3 × 5.8 8 × 10. 65 8 × 6.2 145 (143) 192 6.3 × 5.8 55 6.3 × 5.8 45 8 × 6.2 95 (94) 8 × 10. 140 (105) 238 289 6.3 × 5.8 8 × 6.2 8 × 10. 8 × 10. 31 46 96 117 140 232 4 0G 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 63 1J 100 2A 6.3 × 5.8 8 × 10. 8 × 10. 10 × 10. 10 × 10. 29 77 100 130 155 8 × 6.2 40 (35) 8 × 6.2 105 (94) 8 × 10. 8 × 10. 175 (132) 10 × 10. 195 (181) 10 × 10. 8 × 10. 214 10 × 10. 8 × 6.2 175 (173) 8 × 10. 215 (162) 10 × 10. 250 (232) 10 × 10. 265 (246) 10 × 10. 8 × 10. 270 10 × 10. 305 (284) 10 × 10. 324 (307) 10 × 10. 393 10 × 10. 330 10 × 10. 396 318 10 × 10. 10 × 10. 400 (372) 10 × 10. 10 × 10. 489 Case size φD × L (mm) Rated ripple Size φ6.3 × 5.8 is available for capacitors marked. " " Size φ6.3 × 7.7 is available for capacitors marked. " " Size φ8 × 10 is available for capacitors marked. " " In this case, 6 will be put at 12th digit of type numbering system. Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Cap.(µF) Frequency 00 ~ 47V 100 ~ 1500 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz~ 1.67 1.30 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UG(p.75) series if high CV products are required. Please refer to page 3 for the minimum order quantity. CAT.8100V