UUR1H101MNL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UUR Chip Type, High CV Chip type, higher capacitance. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UUG UUR Extended range Higher C/V UWX Specifications Item Performance Characteristics –40 to +85°C 4 to 100V 3.3 to 1500µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV (µA) . Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) 4 0.35 Rated voltage (V) tan δ (MAX.) 6.3 0.28 10 0.24 16 0.20 25 0.16 35 0.14 50 0.12 63 0.12 100 0.12 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) Z–40°C / Z+20°C 4 7 15 6.3 5 10 10 4 8 16 3 6 25 2 4 Capacitance change tan δ Leakage current 35 2 3 50 2 3 63 2 3 100 2 3 Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C. Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Chip Type 1 L±0.5 Pressure relief vent L±0.5 1 B±0.2 7 8 9 10 11 12 13 14 Size code UUR 1 A 1 0 1 M C L 1GS Configuration 2 3 4 5 6 7 8 9 code φ D ×Package L Code code 6.3 × 5.8 SizeCL 6.3 × 7.7 CL Configuration Rated voltage (10V) 8 × 6.2 CL Capacitance tolerance (±20%) φ D × L Code Series name 8 × 10 NL 6.3 × 5.8 CL Rated capacitance (100µF) Type 10 × 10 NL 6.3 × 7.7 CL Rated voltage (10V) (mm) 8 × 6.2 CL Series name 8 × 6.2 8 × 10 10 × 10 8 × 10 NL Type 3.3 2.9 3.2 10 × 10 NL 8.3 8.3 10.3 (mm) 8.3 8.3 10.3 8 × 6.2 8 × 10 10 × 10 2.3 3.1 4.5 3.3 2.9 3.2 6.2 10 10 10.3 0.58.3 to 0.8 0.88.3 to 1.1 0.8 to 1.1 8.3 8.3 10.3 2.3 3.1 4.5 6.2 10 10 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Capacitance tolerance (±20%) Rated capacitance (100µF) 0.5MAX. φD×L Positive C±0.2 H 6 Negative C±0.2 H 5 10 11 12 13 14 Positive B±0.2 φD±0.5 Plastic platform 0.3MAX. 2 Voltage φD±0.5 A2 220 16V Capacitance A2 220 16V Trade mark 0.5MAX. H 1 Size φ8 × 6.2 only 2 Voltage mark for 6.3V is 6V . Plastic platform Lot No. Capacitance 0.3MAX. (φ8 × 10, φ10) 2 Voltage Trade mark 4 Negative 6V . L±0.3 A±0.2 E A±0.2 A±0.2 E A±0.2 H 0.5MAX. A2 100 10V C±0.2 B±0.2 L±0.3 1 Trade1 mark Size φ8 × 6.2 only 2 Voltage mark for 6.3V is B±0.2 φD±0.5 φD±0.5 A2 100 10V 0.3MAX. 3 Package code Positive Plastic platform 2Voltage 0.5MAX. C±0.2 0.3MAX. 2Voltage 2 UUR 1 A 1 0 1 M C L 1GS A±0.2 E A±0.2 A±0.2 E A±0.2 Capacitance Positive Plastic platform Lot No. Lot No. Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 10V 100µF) (φ6.3, φ8 × 6.2) Capacitance 1 Trade Lot No.mark Capacitance change tan δ Leakage current Negative Negative Pressure relief vent Dimension table in next page. 168 6.3 × 5.8 6.3 × 7.7 A 2.4 B 6.6 Cφ D × L 6.6 6.3 × 5.8 E 2.2 AL 2.4 5.8 BH 0.56.6 to 0.8 C 6.6 E 2.2 L 5.8 H 0.5 to 0.8 2.4 6.6 6.6 6.3 × 7.7 2.2 2.4 7.7 0.56.6 to 0.8 6.6 2.2 7.7 0.5 to 0.8 ALUMINUM  ELECTROLYTIC  CAPACITORS UUR Dimensions Cap.(µF) V Code 3.3 3R3 4.7 4R7 4 6.3 10 16 25 35 50 63 0G 0J 1A 1C 1E 1V 1H 1J 100 22 220 33 330 47 470 100 101 150 151 220 221 330 331 6.3 × 5.8 470 471 680 681 1000 6.3 × 5.8 6.3 × 5.8 6.3 × 5.8 70 8 × 6.2 125 65 8 × 6.2 145 (143) 6.3 × 5.8 85 6.3 × 7.7 151 8 × 10. 6.3 × 5.8 8 × 10. 8 × 10. 284 8 × 10. 102 8 × 10. 344 318 10 × 10. 10 × 10. 400 (372) 10 × 10. 152 10 × 10. 347 10 × 10. 265 Frequency 50 Hz 0.80 0.85 120 Hz 1.00 1.00 489 300 Hz 1.15 1.08 77 8 × 10. 100 130 155 8 × 10. Case size φD × L Rated ripple 214 232 396 454 (mm) Rated ripple current (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current 00 Less than 47V 100 to 1500 8 × 10. 96 10 × 10. 10 × 10. 200 8 × 10. 46 8 × 10. 10 × 10. 374 6.3 × 7.7 8 × 6.2 140 290 240 8 × 6.2 40 (35) 117 289 8 × 10. 31 8 × 10. 238 152 1 kHz 1.40 1.20 29 6.3 × 5.8 8 × 6.2 105 (94) 8 × 10. 8 × 10. 175 (132) 10 × 10. 195 (181) 10 × 10. 10 × 10. 8 × 6.2 175 (173) 192 55 45 8 × 6.2 95 (94) 8 × 10. 140 (105) 8 × 10. 215 (162) 10 × 10. 250 (232) 10 × 10. 265 (246) 10 × 10. 8 × 10. 270 10 × 10. 305 (284) 10 × 10. 324 10 × 10. 330 (307) 10 × 10. 393 8 × 6.2 160 (143) 8 × 6.2 190 (188) Size φ6.3 × 5.8 is available for capacitors marked. " " Size φ6.3 × 7.7 is available for capacitors marked. " " Size φ8 × 10 is available for capacitors marked. " " In this case, 6 will be put at 12th digit of type numbering system. Cap.(µF) 2A 6.3 × 5.8 10 1500 100 10 kHz or more 1.67 1.30 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UUG(p.174) if high CV products are required. Please refer to page 3 for the minimum order quantity. 169