ALUMINUM ELECTROLYTIC CAPACITORS
UT
6mmL Chip Type , Wide Temperature Range
series
Chip type with load life 2000 hours at +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC).
UA Long Life
UT
UX Higher C/V
Long Life
WT
Specifications
Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Performance Characteristics
– 55 ~ +105°C 4 ~ 50V 0.1 ~ 100µF ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Measurement frequency :120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.)
4 0.37
6.3 0.28 4 6 12
10 0.24 6.3 3 8
16 0.20 10 3 5
25 0.16 16 2 4 25 2 3
35 0.13 35 2 3
50 0.12 50 2 3
Measurement frequency :120Hz
Stability at Low Temperature
Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.)
Endurance
After 2000 hours' application of rated voltage at 105°C , capacitors meet the characteristic requirements listed at right.
Capacitance change tan δ Leakage current
Within ±25% of initial value (16V or less) Within ±20% of initial value (25V or more) 200% or less of initial specified value Initial specified value or less
Shelf Life Resistance to soldering heat Marking
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C C apacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Black print on the case top.
Chip Type
105°C Marking Capacitance Lot No. Voltage Plastic platform 0.3MAX. C ± 0.2 0.5MAX. Positive
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUT 1C 1 0 0 MCL1GS
φD 4
X2P 10 16V
φD ± 0.5
B ± 0.2
E
A B C E L
1.8 4.3 4.3 1.0 5.8
5 2.1 5.3 5.3 1.3 5.8
(mm) 6.3 2.4 6.6 6.6 2.2 5.8
Taping code Configuration Capacitance tolerance (± 20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Type
Voltage mark for 6.3V is
6V .
L ± 0.3
0.5 ~ 0.8
Negative
Dimensions
V Cap.(µF) Code
4 0G
6.3 0J
A ± 0.2
A ± 0.2
10 1A
16 1C
25 1E
35 1V 4 4 4 4 4 4 4 5 6.3
50 1H 1.0 2.6 3.2 3.8 6.2 11 14 19 30
0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100
0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101
4 5 5 6.3
22 30 36 60
4 5 5 6.3
22 30 36 60
5 5 6.3 6.3
27 35 46 60
4 5 6.3 6.3
18 30 40 50
4 5 6.3 6.3
13 23 38 48
4 5 6.3
15 25 42
Case size φ D (mm)
Allowable Rated ripple ripple
Rated Ripple (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50
Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UX(p.74), UJ(p.76) series if high C/V products are required. Please refer to page 3 for the minimum order quantity.
CAT.8100V
很抱歉,暂时无法提供与“UUT1V101MCL”相匹配的价格&库存,您可以联系我们找货
免费人工找货