UUX0J471MNL6GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UX Chip Type, Wide Temperature Range series Chip type, operating over wide temperature range of to -55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). UJ UB LR High Temperature High Voltage UX Extended range Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C (6.3 to 100V), –40 to +105°C (160 to 400V) Rated Voltage Range 6.3 to 400V Rated Capacitance Range 1 to 1000µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current Rated voltage (V) 6.3 to 100 160 to 400 Leakage Current After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA). I = 0.04CV+100 (  µA) max.(1 minute's) Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 6.3 0.22 10 0.19 16 0.16 25 0.14 35 0.12 50 0.10 63 0.10 100 0.08 160 0.20 200 0.20 250 0.20 400 0.25 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio ZT / Z20 (MAX.) Z–55°C / Z+20°C Z–40°C / Z+20°C 6.3 4 10 4 — — 16 3 25 3 35 3 50 2 63 3 100 4 — — — — — — Capacitance change tan δ Leakage current 160 200 250 — — — 400 — 6 6 6 10 Within ±20% of the initial capacitance value 200% or less than the intial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours (160 to 400V : 3000hours) at 105°C. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Resistance to soldering heat Marking Capacitance change tan δ Leakage current Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Black print on the case top. Chip Type Type numbering system (Example : 10V 100µF) 1 Plastic platform 0.3MAX. C±0.2 H L±0.3 H 1 Size φ8×6.2 only 2 Voltage mark for 6.3V is 6V . C±0.2 Plastic platform 0.3MAX. C±0.2 L±0.5 Lot No. Capacitance B±0.2 φD±0.5 Pressure relief vent H L±0.5 Pressure relief vent 7 8 9 10 11 12 13 14 H A±0.2 A±0.2 A±0.2 Rated capacitance (100µF) Rated voltage (10V) Series name D×L Code 6.3 × 7.7 CL 8 × 6.2 CL 8 × 10 NL 10 × 10 NL Type φ D× L E Capacitance 6 Capacitance tolerance (±20%) Negative Positive B±0.2 Lot No. Trade mark φD±0.5 A2P 100 16V A2P 100 16V 2 Voltage 5 Size code Negative Positive Plastic platform 0.3MAX. 105˚C Marking (φ8 × 10, φ10 × 10)2 Voltage 105˚C Marking Trade mark 4 Configuration A±0.2 B±0.2 C±0.2 E L±0.3 3 Package code A±0.2 A±0.2 A±0.2 A±0.2 2 Voltage mark for 6.3V is 6V . Capacitance Lot No. Plastic platform 0.3MAX. 2 UUX 1 A 1 0 1 M C L 1GS Positive B±0.2 Capacitance Lot No. 1 Trade mark 1 Size φ8×6.2 only φD±0.5 A2P 100 10V 2 Voltage A2P 100 10V 1 105˚C Marking Trade mark φD±0.5 2 Voltage 105˚C Marking 0.5MAX. 0.5MAX. E Positive 0.5MAX. 0.5MAX. E (φ6.3, φ8 × 6.2) A B C E L H (mm) 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 2.4 3.3 2.9 3.2 6.6 8.3 8.3 10.3 6.6 8.3 8.3 10.3 2.2 2.3 3.1 4.5 7.7 6.2 10 10 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Negative Negative Dimension table in next page. CAT.8100D ALUMINUM  ELECTROLYTIC  CAPACITORS UX series Dimensions Cap. (μF) 4.7 6.3 0J V Code 4R7 10 1A 16 1C 10 100 22 220 33 330 47 470 100 101 220 221 330 331 470 471 173 8×10 288 10×10 318(296) 10×10 340(316) 10×10 351(326) 680 681 10×10 408 1000 102 10×10 495 25 1E 35 1V 63 1J 8×6.2 8×6.2 67(64) 8×6.2 76(75) 8×6.2 8×6.2 90 8×10 161(121) 8×10 10×10 160 2C 79(78) 8×10 148(111) 8×10 181 10×10 330(307) 10×10 351(283) 10×10 441(410) 10×10 372 250 2E 8×10 25 1.8 1R8 8×10 26 2.2 2R2 8×10 27 3.3 3R3 8×10 31 8×10 31 10×10 38 3.9 3R9 8×10 34 8×10 34 10×10 39 4.7 4R7 8×10 37 8×10 37 10×10 40 6.8 6R8 8×10 44 8×10 44 10×10 64 10×10 64 100 8×10 57 180 10×10 64 133 10×10 310 51 8×10 108 10×10 185(179) 8×10 10×10 220 10×10 320 75 10×10 150(121) 10×10 180 10×10 230 Case size φD × L (mm) Rated ripple 450 400 2G 1 18 10×10 8×10 10×10 180(167) 100 2A 42 8×6.2 489 10×10 200 2D 10 124 10×10 304(283) 8×10 392 V Code 010 Cap. (μF) 50 1H Rated ripple current (mArms) at 105°C 120Hz Size φ6.3 × 7.7 is available for capacitors marked. " " / Size φ8 × 10 is available for capacitors marked. " " In this case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Cap.(µF) Frequency 0001 to 47V00 100 to 1000 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz or more 1.67 1.30 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UJ(p.160) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100D