UUX1A471MNL6GS

ALUMINUM ELECTROLYTIC CAPACITORS UUX Chip Type, Wide Temperature Range Chip type, operating over wide temperature range of to -55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UUJ UUB ULR High Temperature High Voltage UUX Extended range Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C (6.3 to 100V), –40 to +105°C (160 to 400V) Rated Voltage Range 6.3 to 400V Rated Capacitance Range 1 to 1000µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current Rated voltage (V) 6.3 to 100 160 to 400 Leakage Current After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV (µA). I = 0.04CV+100 ( µA) max.(1 minute's at 20°C) Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 6.3 0.22 10 0.19 16 0.16 25 0.14 35 0.12 50 0.10 63 0.10 100 0.08 160 0.20 200 0.20 250 0.20 400 0.25 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio ZT / Z20 (MAX.) Z–55°C / Z+20°C Z–40°C / Z+20°C 6.3 4 10 4 — — 16 3 25 3 35 3 50 2 63 3 100 4 — — — — — — Capacitance change tan δ Leakage current 160 200 250 — — — 400 — 6 6 6 10 Within ±20% of the initial capacitance value 200% or less than the intial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours (160 to 400V : 3000hours) at 105°C. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Resistance to soldering heat Marking Capacitance change tan δ Leakage current Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Black print on the case top. Chip Type Type numbering system (Example : 10V 100µF) 1 L±0.3 2 Voltage mark for 6.3V is 6V . Capacitance Lot No. C±0.2 B±0.2 0.3MAX. B±0.2 Capacitance Lot No. 1 Trade mark 1 Size φ8×6.2 only φD±0.5 2 Voltage A2P 100 10V 1 105˚C Marking Trade mark φD±0.5 A2P 100 10V Plastic platform 0.5MAX. C±0.2 0.3MAX. 2 Voltage 105˚C Marking 0.5MAX. Plastic platform H 3 Capacitance L±0.5 H Pressure relief vent Lot No. Capacitance L±0.5 Pressure relief vent H 0.5MAX. 0.5MAX. φD±0.5 C±0.2 B±0.2 B±0.2 A2P 100 16V Lot No. Trade mark φD±0.5 A2P 100 16V Plastic platform 9 10 11 12 13 14 Capacitance tolerance (±20%) Rated capacitance (100µF) Rated voltage (10V) Series name Negative Negative D×L Code 6.3 × 7.7 CL 8 × 6.2 CL 8 × 10 NL 10 × 10 NL Type A B C E L H Positive A±0.2 E A±0.2 A±0.2 E A±0.2 C±0.2 2 Voltage 2 Voltage 8 Size code Positive Plastic platform 105˚C Marking Trade mark 7 Configuration φ D× L 0.3MAX. 6 Positive 1 Size φ8×6.2 only 105˚C Marking (φ8 × 10, φ10) 5 Taping code Negative 2 Voltage mark for 6.3V is 6V . 0.3MAX. 4 Negative H L±0.3 2 UUX 1 A 1 0 1 M C L 1GS Positive A±0.2 E A±0.2 A±0.2 E A±0.2 (φ6.3, φ8 × 6.2) (mm) 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 2.4 3.3 2.9 3.2 6.6 8.3 8.3 10.3 6.6 8.3 8.3 10.3 2.2 2.3 3.1 4.5 7.7 6.2 10 10 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Frequency coefficient of rated ripple current Cap.(µF) Frequency 0001 to 47V00 100 to 1000 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz or more 1.67 1.30 Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UUX ■ Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） 25 （1E） 35 （1V） 50 （1H） 63 （1J） Rated Capacitance （µF） Case Size φD×L（mm） tan δ Leakage Current （µA） at 20℃ after 1 minute （ ） Rated Ripple （mArms） （105℃/120Hz） Part Number 220 8× 10 0.22 41.58 161 UUX0J221MNL1GS 220 6.3× 7.7 0.22 41.58 121 UUX0J221MCL6GS 330 8× 10 0.22 62.37 288 UUX0J331MNL1GS 470 10× 10 0.22 88.83 340 UUX0J471MNL1GS 470 8× 10 0.22 88.83 316 UUX0J471MNL6GS 680 10× 10 0.22 128.52 408 UUX0J681MNL1GS 1000 10× 10 0.22 189 495 UUX0J102MNL1GS 100 8× 6.2 0.19 30 90 UUX1A101MCL1GS 220 8× 10 0.19 66 173 UUX1A221MNL1GS 330 10× 10 0.19 99 318 UUX1A331MNL1GS 330 8× 10 0.19 99 296 UUX1A331MNL6GS 470 10× 10 0.19 141 351 UUX1A471MNL1GS 470 8× 10 0.19 141 326 UUX1A471MNL6GS 680 10× 10 0.19 204 392 UUX1A681MNL1GS 100 8× 10 0.16 48 148 UUX1C101MNL1GS 100 6.3× 7.7 0.16 48 111 UUX1C101MCL6GS 220 10× 10 0.16 105.6 330 UUX1C221MNL1GS 220 8× 10 0.16 105.6 307 UUX1C221MNL6GS 330 10× 10 0.16 158.4 441 UUX1C331MNL1GS 330 8× 10 0.16 158.4 410 UUX1C331MNL6GS 470 10× 10 0.16 225.6 489 UUX1C471MNL1GS 47 8× 6.2 0.14 35.25 79 UUX1E470MCL1GS 47 6.3× 7.7 0.14 35.25 78 UUX1E470MCL6GS 100 8×10 0.14 75 181 UUX1E101MNL1GS 220 10×10 0.14 165 351 UUX1E221MNL1GS 220 8×10 0.14 165 283 UUX1E221MNL6GS 330 10×10 0.14 247.5 372 UUX1E331MNL1GS 33 8× 6.2 0.12 34.65 76 UUX1V330MCL1GS 33 6.3× 7.7 0.12 34.65 75 UUX1V330MCL6GS 47 8× 10 0.12 100 10× 10 0.12 49.35 105 124 UUX1V470MNL1GS 304 UUX1V101MNL1GS 100 8× 10 0.12 105 283 UUX1V101MNL6GS 220 10× 10 0.12 231 450 UUX1V221MNL1GS 22 8× 6.2 0.10 33 67 UUX1H220MCL1GS 22 6.3× 7.7 0.10 33 64 UUX1H220MCL6GS 33 8× 10 0.10 49.5 133 UUX1H330MNL1GS 47 10× 10 0.10 70.5 180 UUX1H470MNL1GS 47 8× 10 0.10 100 10× 10 0.10 70.5 150 167 UUX1H470MNL6GS 310 UUX1H101MNL1GS 10 8× 6.2 0.10 18.9 51 UUX1J100MCL1GS 22 8× 10 0.10 41.58 108 UUX1J220MNL1GS 33 10× 10 0.10 62.37 185 UUX1J330MNL1GS 33 8× 10 0.10 62.37 179 UUX1J330MNL6GS 47 10× 10 0.10 100 10× 10 0.10 88.83 189 220 UUX1J470MNL1GS 320 UUX1J101MNL1GS CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UUX ■ Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 4.7 100 （2A） 160 （2C） （ ） Rated Ripple （mArms） （105℃/120Hz） Part Number 8×6.2 0.08 14.1 42 UUX2A4R7MCL1GS 0.08 30 75 UUX2A100MNL1GS 22 10× 10 0.08 66 150 UUX2A220MNL1GS 22 8× 10 0.08 66 121 UUX2A220MNL6GS 33 10× 10 0.08 99 180 UUX2A330MNL1GS 47 10× 10 0.08 141 230 UUX2A470MNL1GS 10 8×10 0.20 164 57 UUX2C100MNL1GS 18 10× 10 0.20 215.2 64 UUX2C180MNL1GS 8× 10 0.20 126.4 31 UUX2D3R3MNL1GS 3.9 8× 10 0.20 131.2 34 UUX2D3R9MNL1GS 4.7 8× 10 0.20 137.6 37 UUX2D4R7MNL1GS 6.8 400 （2G） Leakage Current （µA） at 20℃ after 1 minute 8× 10 10 250 （2E） tan δ 10 3.3 200 （2D） Case Size φD×L（mm） 8× 10 0.20 154.4 44 UUX2D6R8MNL1GS 10× 10 0.20 180 64 UUX2D100MNL1GS 3.3 8× 10 0.20 133 31 UUX2E3R3MNL1GS 3.9 8× 10 0.20 139 34 UUX2E3R9MNL1GS 4.7 8× 10 0.20 147 37 UUX2E4R7MNL1GS 6.8 8× 10 0.20 168 44 UUX2E6R8MNL1GS 10 10× 10 0.20 200 64 UUX2E100MNL1GS 1 8× 10 0.25 116 25 UUX2G010MNL1GS 1.8 8× 10 0.25 128.8 26 UUX2G1R8MNL1GS 2.2 8×10 0.25 135.2 27 UUX2G2R2MNL1GS 3.3 10× 10 0.25 152.8 38 UUX2G3R3MNL1GS 3.9 10× 10 0.25 162.4 39 UUX2G3R9MNL1GS 4.7 10× 10 0.25 175.2 40 UUX2G4R7MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. Please select UUJ if high C/V products are required. CAT.8100K