UWD1H221MCL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UWD Chip Type, Low Impedance High Temperature (260°C) Reflow Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times (φ10 × 10 : 1 time) Chip type, low impedance temperature range up to +105°C. UWD Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. High Temperature Reflow UUD Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C Rated voltage (V) 6.3 10 16 25 35 50 tan δ (MAX.) 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) Tangent of loss angle (tan δ) ( ) is φ8 over Measurement frequency : 120Hz 6.3 3 5 Rated voltage (V) Z– 25°C / Z+20°C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Z– 55°C / Z+20°C 10 2 4 The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours (2000 hours for φD = 4, 5 and 6.3) at 105°C. Endurance Shelf Life Resistance to soldering heat 50 2 3 35 2 3 25 2 3 16 2 4 Within ±30% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic tan δ Less than or equal to the initial specified value requirements listed at right when they are removed from the plate Leakage current Less than or equal to the initial specified value and restored to 20°C. Black print on the case top. Marking Chip Type Type numbering system (Example : 16V 22µF) (φ4 to φ6.3) H L±0.3 Capacitance 3 4 5 6 7 8 9 10 11 12 13 14 Package code A±0.2 E A±0.2 B±0.2 φD±0.5 A2 33C WD C±0.2 0.3 MAX. Series 2 UWD 1 C 2 2 0 M C L 1 G S 0.5 MAX. Plastic platform Voltage (C:16V) Lot No. 1 Positive Configuration Capacitance tolerance (±20%) Rated capacitance (22µF) Negative Rated voltage (16V) Series name Type (φ8,φ10) Lot No. Voltage V 6.3 Code j Capacitance 10 A C±0.2 16 C H L±0.5 25 E 35 V (mm) φD×L A B C E L H A±0.2 E A±0.2 0.3 MAX. B±0.2 A2 100V WD Trade mark Plastic platform Series φD±0.5 Voltage (V:35V) 0.5 MAX. Positive Negative 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 10 10 × 10 1.8 4.3 4.3 1.0 5.8 0.5 to 0.8 2.1 5.3 5.3 1.3 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 7.7 0.5 to 0.8 2.9 8.3 8.3 3.1 10 0.8 to 1.1 3.2 10.3 10.3 4.5 10 0.8 to 1.1 50 H Dimension table in next page. 143 CAT.8100H ALUMINUM  ELECTROLYTIC  CAPACITORS UWD Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 1 010 4 × 5.8 5.00 30 2.2 2R2 4 × 5.8 5.00 30 3.3 3R3 4 × 5.8 5.00 30 4.7 4R7 4 × 5.8 1.80 80 5 × 5.8 1.52 85 10 100 15 150 22 220 27 270 4 × 5.8 1.80 80 5 × 5.8 0.76 150 33 330 5 × 5.8 0.76 150 47 4 × 5.8 1.80 80 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165 4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165 4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185 470 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185 56 560 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.34 300 68 680 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.34 300 100 101 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.34 300 150 151 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.18 670 220 221 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 6.3 × 7.7 0.34 280 8 × 10 0.17 450 10 × 10 0.09 670 10 × 10 0.18 670 330 331 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.09 670 10 × 10 0.09 670 470 471 8 × 10 0.17 450 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.09 670 680 681 8 × 10 0.17 450 10 × 10 0.09 670 10 × 10 0.09 670 1000 102 10 × 10 0.09 670 10 × 10 0.09 670 1500 152 10 × 10 0.09 670 Case size φ D × L (mm) Impedance Rated ripple Max. Impedance (Ω) at 20°C 100kHz, Rated ripple current (mArms) at 105°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 144 CAT.8100H