UWF1E100MCL1GB

ALUMINUM  ELECTROLYTIC  CAPACITORS UWF Chip type, low impedance temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. Products which are scheduled to be discontinued. Not recommended for new designs. Low Impedance UWG UWF Low Impedance UWT Specifications Item Performance Characteristics Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current –55 to +105°C 6.3 to 35V 1 to 220µF ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.22 Rated voltage (V) tan δ ( max.) Tangent of loss angle (tan δ) 10 0.19 16 0.16 25 0.14 35 0.12 Measurement frequency : 120Hz 10 2 4 6.3 2 4 Rated voltage (V) Impedance ratio Z(– 25°C) / Z(+20°C) ZT / Z20 ( max.) Z(– 55°C) / Z(+20°C) Stability at Low Temperature 35 2 3 25 2 3 16 2 3 Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Capacitance change tan δ Leakage current Capacitance change tan δ Leakage current Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Type numbering system (Example : 16V 10µF) Chip Type (φ4 to φ6.3) 0.5 MAX. C0.2 Plastic platform Voltage A2P 100 16V 0.5 to 0.8 Lot No. 0.3 max. 0.5 max. 4 5 6 7 8 9 10 11 12 13 14 8 φD Code 4 to 6.3 GB 9 10 11 12 13 14 U W F 1 C 1 0 0 M C L 18 G B GS 8 3.3 8.3 8.3 2.3 Capacitance tolerance (±20%) Negative Positive φD C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 Rated voltage (16V) Rated capaci Series name Rated v Type S 0.5 to 0.8 Voltage mark for 6.3V is 6V. 8 3.3 8.3 8.3 2.3 Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 C Capacitance toler (mm) A B 8 Rated capacitance (10µF) Voltage mark for 6.3V is 6V. Negative φD 4 to Configuration A±0.2 E A±0.2 (mm) 0.5φD to 0.84 5 6.3 1.8 2.1 2.4 A 4.3 5.3 6.6 B 4.3 5.3 6.6 C 1.0 1.3 2.2 E C±0.2 Negative 6.2±0.3 3 Taping code B ± 0.2 Trade mark 6.20.3 +0.1 -0.2 A0.2 A0.2 B+– 0.2 φD0.5 Capacitance 5.4 2 0.5 max. Positive Plastic platform 0.3 MAX. Voltage (φ8) 1 U W F 1 C 1 0 01 M2 C3 L4 15 G 6B 7 A±0.2 E A±0.2 Negative 0.5 to 0.8 C±0.2 B±0.2 A0.2 A0.2 E φD±0.5 A2P 10 16V +0.1 -0.2 105˚C Marking X2P 100 16V 0.3 max. E 05˚C Marking Capacitance rade mark Voltage B0.2 φD0.5 X2P 10 16V 5.4 Positive C0.2Plastic platform Voltage Lot No. 0.5 MAX. Plastic platform 105˚C Marking 0.3 MAX. Capacitance Positive φD±0.5 05˚C Marking Capacitance ot No. ot No. Chip Type, Low Impedance 10 kHz or more 1.00　　 Dimension table in next page. CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UWF Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） 25 （1E） 35 （1V） Leakage Current Impedance（Ω） Rated Ripple （µA） （mArms） max. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes Rated Capacitance （µF） Case Size φD×L（mm） tan δ 22 4×5.4 0.22 3 5.0 50 UWF0J220MCL1GB 33 5× 5.4 0.22 3 2.6 80 UWF0J330MCL1GB 47 5× 5.4 0.22 3 2.6 80 UWF0J470MCL1GB （ ） Part Number 68 6.3×5.4 0.22 4.284 1.3 115 UWF0J680MCL1GB 100 6.3×5.4 0.22 6.3 1.3 115 UWF0J101MCL1GB 150 8×6.2 0.22 9.45 0.8 150 UWF0J151MCL1GS 220 8×6.2 0.22 13.86 0.8 150 UWF0J221MCL1GS 22 5× 5.4 0.19 3 2.6 80 UWF1A220MCL1GB 33 5× 5.4 0.19 3.3 2.6 80 UWF1A330MCL1GB 47 6.3×5.4 0.19 4.7 1.3 115 UWF1A470MCL1GB 68 6.3×5.4 0.19 6.8 1.3 115 UWF1A680MCL1GB 100 8×6.2 0.19 10 0.8 150 UWF1A101MCL1GS 150 8×6.2 0.19 15 0.8 150 UWF1A151MCL1GS 10 4× 5.4 0.16 3 5.0 50 UWF1C100MCL1GB 15 5× 5.4 0.16 3 2.6 80 UWF1C150MCL1GB 22 5× 5.4 0.16 3.52 2.6 80 UWF1C220MCL1GB 33 6.3×5.4 0.16 5.28 1.3 115 UWF1C330MCL1GB 47 6.3×5.4 0.16 7.52 1.3 115 UWF1C470MCL1GB 68 8×6.2 0.16 10.88 0.8 150 UWF1C680MCL1GS 100 8× 6.2 0.16 16 0.8 150 UWF1C101MCL1GS 4.7 4×5.4 0.14 3 5.0 50 UWF1E4R7MCL1GB 6.8 4×5.4 0.14 3 5.0 50 UWF1E6R8MCL1GB 10 5×5.4 0.14 3 2.6 80 UWF1E100MCL1GB 15 6.3× 5.4 0.14 3.75 1.3 115 UWF1E150MCL1GB 22 6.3× 5.4 0.14 5.5 1.3 115 UWF1E220MCL1GB 33 6.3× 5.4 0.14 8.25 1.3 115 UWF1E330MCL1GB 47 8× 6.2 0.14 11.75 0.8 150 UWF1E470MCL1GS 68 8× 6.2 0.14 17 0.8 150 UWF1E680MCL1GS 1 4×5.4 0.12 3 5.0 50 UWF1V010MCL1GB 1.5 4×5.4 0.12 3 5.0 50 UWF1V1R5MCL1GB 2.2 4×5.4 0.12 3 5.0 50 UWF1V2R2MCL1GB 3.3 4×5.4 0.12 3 5.0 50 UWF1V3R3MCL1GB 4.7 4×5.4 0.12 3 5.0 50 UWF1V4R7MCL1GB 6.8 5×5.4 0.12 3 2.6 80 UWF1V6R8MCL1GB 10 5×5.4 0.12 3.5 2.6 80 UWF1V100MCL1GB 15 6.3×5.4 0.12 5.25 1.3 115 UWF1V150MCL1GB 22 6.3×5.4 0.12 7.7 1.3 115 UWF1V220MCL1GB 33 8× 6.2 0.12 11.55 0.8 150 UWF1V330MCL1GS 47 8× 6.2 0.12 16.45 0.8 150 UWF1V470MCL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. Please select UUJ if high C/V products are required. CAT.8100L