ALUMINUM ELECTROLYTIC CAPACITORS
WH
Chip Type, High Reliability High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times (φ8 × 6.2, φ10 × 10 : 1 time) Chip type high temperature range, for +125°C use.
WH
High Temperature
Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC).
Reflow
UB
Specifications
Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Performance Characteristics
– 40 ~ +125°C 10 ~ 50V 10 ~ 330µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.)
10 0.32
16 0.24 10 12
25 0.21 16 8 25 6
35 0.18 35 4
50 0.18 50 4
Measurement frequency : 120Hz
Stability at Low Temperature
Rated voltage (V)
Impedance ratio ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
Endurance
After 1000 hours' application of rated voltage at 125°C, capacitors meet the characteristic requirements listed at right.
Capacitance change tan δ Leakage current
Within ±30% of initial value 300% or less of intial specified value Initial specified value or less
Shelf Life Resistance to soldering heat Marking
After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Black print on the case top.
Chip Type
(φ8 × 6.2)
Type numbering system (Example : 10V 100µF)
Voltage (A:10V) Series
D±0.5
C±0.2
0.5MAX.
Plastic platform 0.3MAX. B±0.2
Positive A±0.2 A±0.2
UWH 1 A 1 0 1 M C L 1 G S
Package code Configuration Capacitance tolerance (±20%) Rated Capacitance (100mF) Rated voltage (10V) Series name Type A B C E L H
f´
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Trade mark
N2 100A WH
f
Lot No. Capacitance
L±0.3
H
E
Negative
(φ8 × 10, φ10 × 10)
Voltage (V:35V) Series
0.5MAX.
Plastic platform 0.3MAX. B±0.2
C±0.2
Positive A±0.2 A±0.2
DL
Trade mark
Lot No. Capacitance
Voltage
V Code 10 A 16 C 25 E 35 V
L±0.5
8 ´ 6.2 3.3 8.3 8.3 2.3 6.2 0.5 ~ 0.8
8 ´ 10 2.9 8.3 8.3 3.1 10 0.8 ~ 1.1
10 ´ 10 3.2 10.3 10.3 4.5 10 0.8 ~ 1.1
(mm)
N2 100V WH
D±0.5
f
H
50 H
Dimension table in next page.
E
Negative
CAT.8100V
ALUMINUM ELECTROLYTIC CAPACITORS
WH
Cap.(µF)
series
Dimensions
V Code
10 1A
16 1C
25 1E
35 1V
8 × 6.2 8 × 6.2 8 × 6.2 44 52 80 8 × 10 10 × 10
50 1H
24 38 46 58
10 22 33 47 100 220 330
100 220 330 470 101 221 331 8 × 6.2 8 × 10 10 × 10 58 90 112 8 × 10 10 × 10 66 102 8 × 6.2 8 × 10 10 × 10 48 74 116 8 × 10 10 × 10
Case size φ D × L (mm)
Rated ripple
Rated Ripple (mArms) at 125°C 120Hz
Frequency coefficient of rated ripple current
Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50
Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity.
CAT.8100V
很抱歉,暂时无法提供与“UWH1H331MCL”相匹配的价格&库存,您可以联系我们找货
免费人工找货