UWJ1V220MCL

ALUMINUM ELECTROLYTIC CAPACITORS WJ 5.5mmL Chip Type High Temperature (260°C) Reflow series Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Load life of 2000 hours at 85°C Adapted to the RoHS directive (2002/95/EC). WJ High Temperature Reflow WX Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Performance Characteristics – 40 ~ +85°C 6.3 ~ 50V 0.1 ~ 150µF ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ (MAX.) 6.3 0.26 10 0.20 16 0.16 6.3 4 8 10 3 8 25 0.14 16 2 4 35 0.12 50 0.12 Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Measurement frequency : 120Hz 50 35 25 2 2 2 3 3 4 Endurance After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage Current Within ±20% of initial value 200% or less of initial specified value Initial specifed value or less Shelf Life After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. Black print on the case top. Capacitance change tan δ Leakage current Resistance to soldering heat Marking Within ±10% of initial value Initial specified value or less Initial specified value or less Chip Type Positive Plastic platform 0.3 MAX. 0.5 MAX. Type numbering system (Example : 16V 10µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UW J 1 C 1 0 0 MC L 1 G B Package code Configuration Voltage (A:10V) Series C ± 0.2 A ± 0.2 A ± 0.2 N2 100A WJ Capacitance toleranc (± 20%) Rated Capacitance (10µF) Rated voltage (16V) Series name φD ± 0.5 B ± 0.2 5.4 Lot No. Capacitance +0.1 – 0.2 E 0.5 ~ 0.8 Negative Type Voltage V Code 6.3 j 10 A 16 C 25 E 35 V 50 H A B C E φD (mm) 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 Dimension table in next page. CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS WJ Cap. (µF) series Dimensions V Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 4 4 4 4 4 4 4 50 1H 1.0 2.0 2.8 4.0 8.4 13 17 20 33 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 150 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 151 4 4 4 5 5 6.3 6.3 28 37 45 70 71 5 5 6.3 6.3 33 41 52 76 5 6.3 6.3 6.3 23 37 49 58 86 5 6.3 6.3 16 27 42 52 4 5 6.3 18 29 45 5 6.3 Case size φ D (mm) Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V