ALUMINUM ELECTROLYTIC CAPACITORS
WP
5.5mmL Chip Type, Bi-Polarized
series
Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC).
WP
Smaller
Specifications
Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ
ZP
Performance Characteristics
– 40 ~ +85°C
6.3 ~ 50V 0.1 ~ 100µF
±20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ (MAX.)
6.3 0.24
10 0.20 6.3 4 8
16 0.17 10 3 6
25 0.17 16 2 4 25 2 4
35 0.15 35 2 3
50 0.15 50 2 3
Measurement frequency : 120Hz
Stability at Low Temperature
Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C
Endurance
After 1000 hours' application of rated voltage at 85°C with the polarity inverted every 250 hours, capacitors meet the characteristic requirements listed at right.
Capacitance change tan δ Leakage current
Within ±20% of initial value 200% or less of initial specified value Initial specified value or less
Shelf Life Resistance to soldering heat Marking
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Initial specified value or less Leakage current listed at right. Black print on the case top.
Chip Type
0.5 MAX. Capacitance Lot No. Voltage Plastic platform 0.3 MAX. C ± 0.2
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWP 1 C 1 0 0 M C L 1 G B
A ± 0.2 A ± 0.2
Taping code Configuration Capacitance tolerance (± 20%)
φD
X2 10 16V
φD ± 0.5
B ± 0.2
E
5.4
Voltage mark for 6.3V is 6V .
+0.1 –0.2
0.5 ~ 0.8
A B C E
4 1.8 4.3 4.3 1.0
5 2.1 5.3 5.3 1.3
(mm) 6.3 8 2.4 3.3 6.6 8.3 6.6 8.3 2.2 2.3
Rated Capacitance (10µF) Rated voltage (16V) Series name Type
Dimensions
V
Cap. (µF)
Code
6.3 0J
10 1A
16 1C
25 1E
35 1V 4 4 4 4 4 5 5 6.3 8
50 1H 1.0 2.0 2.8 4.0 8.4 13 17 20 36 Allowable ripple Rated ripple
0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100
0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101
5 6.3 6.3 8
28 37 45 82
4 6.3 6.3 8
17 33 41 61
4 5 6.3 6.3 8
12 23 37 49 75
5 5 6.3 8 8
12 16 27 50 61
4 5 5 6.3 8
8.4 16 18 29 54
Case size φ D (mm)
Rated Ripple (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50
Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UN(p.77) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity.
CAT.8100V
很抱歉,暂时无法提供与“UWP1E220MCL”相匹配的价格&库存,您可以联系我们找货
免费人工找货