UWS1H101MCL1GS

ALUMINUM ELECTROLYTIC CAPACITORS UWS Chip Type, High CV High Temperature (260°C) Reflow Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times (φ8 × 6.2, φ10 × 10 : 1 time) Chip type higher capacitance in large case size. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). UWS High Temperature Products which are scheduled to be discontinued. Not recommended for new designs Reflow UUR Specifications Item Performance Characteristics Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current –40 to +85°C 6.3 to 50V 22 to 1500µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA) . Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) Stability at Low Temperature Rated voltage (V) Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) Z–40°C / Z+20°C 6.3 0.28 10 0.24 16 0.20 25 0.16 35 0.14 50 0.12 Measurement frequency: 120Hz 6.3 5 10 10 4 8 16 3 6 25 2 4 35 2 3 Capacitance change tan δ Leakage current 50 2 3 Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C. Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Capacitance change tan δ Leakage current Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Chip Type Type numbering system (Example : 10V 100µF) (φ6.3, φ8 × 6.2) UWS 1 A 1 0 1 M C L 1G S 1 Capacitance Lot No. 4 5 6 7 8 9 10 11 12 13 14 L ±0.3 0.5MAX. Package code Configuration A±0.2 E A±0.2 B±0.2 φD±0.5 A2 100A WS 1 Trade mark C±0.2 0.3MAX. Series 3 Positive Plastic platform Voltage (A:10V) 2 H Capacitance tolerance (±20%) Rated capacitance (100μF) Rated voltage (10V) Series name Negative 1 Size φ8 × 6.2 only Type (mm) φ D×L (φ8 × 10, φ10 × 10) A B C E L H Lot No. C±0.2 B±0.2 Trade mark φD±0.5 A2 100V WS Series A±0.2 E A±0.2 Voltage (V:35V) L±0.5 Capacitance 0.5MAX. Positive Plastic platform 0.3MAX. H 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 2.4 6.6 6.6 2.2 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 7.7 0.5 to 0.8 3.3 8.3 8.3 2.3 6.2 0.5 to 0.8 2.9 8.3 8.3 3.1 10 0.8 to 1.1 3.2 10.3 10.3 4.5 10 0.8 to 1.1 Negative Voltage V 6.3 10 16 25 35 50 Code j A C E V H Dimension table in next page. 150 CAT.8100E ALUMINUM ELECTROLYTIC CAPACITORS UWS Dimensions V Cap. (µF) Code 6.3 10 16 25 35 50 0J 1A 1C 1E 1V 1H 22 220 33 330 47 470 100 101 6.3 × 5.8 070 8 × 6.2 150 151 6.3 × 5.8 085 6.3 × 7.7 220 221 8 × 6.2 160 8 × 6.2 175 330 331 8 × 6.2 190 8 × 10 240 470 471 8 × 10 265 8 × 10 680 681 8 × 10 318 10 × 10 1000 102 10 × 10 400 10 × 10 454 1500 152 6.3 × 5.8 10 × 10 045 6.3 × 5.8 055 8 × 6.2 095 8 × 10 140 6.3 × 5.8 065 8 × 6.2 105 125 8 × 6.2 145 8 × 10 175 10 × 10 195 151 8 × 10 192 8 × 10 214 10 × 10 238 8 × 10 215 10 × 10 250 10 × 10 265 10 × 10 289 8 × 10 270 10 × 10 305 10 × 10 324 290 10 × 10 330 10 × 10 393 374 10 × 10 396 Case size Rated φ D × L (mm) ripple 489 Rated ripple current (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Cap.(µF) Frequency 00 Less than 47V 100 to 1500 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz or more 1.67 1.30 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 151 CAT.8100E