UWT0J102MNL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS WT Chip Type, Wide Temperature Range series Chip type operating over wide temperature range of to – 55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). WZ High Temperature Reflow WF Low impeadance UT Long Life WT Smaller ZT Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 4 to 50V Rated Capacitance Range 0.1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 4 0.40 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 6.3 0.30 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance Resistance to soldering heat Marking Chip Type (φ3 to φ8 × 5.4 ) 25 2 4 35 2 3 50 2 3 Within ±25% of the initial capacitance value for capacitors of φ3mm unit, and 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. Capacitance change tan δ 200% or less than the initial specified value Leakage current Less than or equal to the initial specified value A±0.2 E B±0.2 φD±0.5 A2P 100 35V A±0.2 A±0.2 H Negative 1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated voltage is omitted. 2. In case of marking for φ3 units. Lot No is expressed by a digit (month code). Dimension table in next page. 8 2 9 10 11 12 13 14 3 4 5 6 7 8 φD code 3 to 8 (5.4L) GB 6.3 to 10 (L 5.8) GS 9 10 11 12 13 14 3 6.3 Package code Size code Configuration φD 3 4 to 10 φD code 3 to 8 (L 7.7) CL Rated capacitance (10µF) 8 to 10 (L tolerance = 10) NL(±20%) Capacitance Rated voltage (16V) Capacitance tolerance (±20%) Series name Rated capacitance (10µF) Type Rated voltage (16V) Type φD Negative 1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated voltage is omitted. L±0.5 2. case of marking for φ3 units. Lot No is expressed by a digit (month code). LotInNo. Pressure relief vent 7 A±0.2 0.5 MAX. C±0.2 H 1 code 2 1 Configuration φD 3 to 8 (L 7.7) 8 to 10 (L = 10) code CL NL Series name L±0.5 Pressure relief vent 6 Positive A±0.2 B±0.2 1 Voltage A2P 100 35V C±0.2 Plastic platform 0.3 MAX. φD±0.5 Capacitance Plastic platform 0.3 MAX. 5 Positive E 1 10Voltage ) 4 E A±0.2 E B±0.2 3 Apply to φ6.3 × 5.8, φ6.3 × 7.7 3 Negative H 3 2 UWT 1 C 1 0 0 MC L 1 G B Negative H 3 1 UWT 1 C 1 0 0 MC L 1 G B 0.5 MAX. (φ8 × 10, φ10 × 10 ) Lot No. 16 2 4 A±0.2 B±0.2 +0.1 –0.2 (L±0.3) × 0.5 MAX. φD±0.5 2 105˚C Marking (φ8 ×mark 10, φ10 Trade Positive +0.1 3 Apply to φ6.3 L × 5.8, –0.2φ6.3 × 7.7 Capacitance 105˚C Marking Trade mark L C±0.2 A±0.2 0.3 MAX. (L±0.3) Lot No. C±0.2 Voltage φD±0.5 Lot No. 2 A2P 10 16V 10 16V A2P 105˚C Marking Plastic platform Plastic platform 0.3 MAX. 1 0.5 MAX. Positive 1 Voltage 105˚C Marking 10 3 8 Type numbering system (Example : 16V 10µF) (φ3 to φ8 × 5.4 ) Capacitance 6.3 4 8 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within ±10% of the initial capacitance value is maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Black print on the case top. Shelf Life Capacitance 4 7 15 ×L 3 × 5.4 4 × 5.4 A 1.5 1.8 B 3.3 φD 4.3 C 3.3 4.3 E 0.8 1.0 1.3 2.2 L 5.4 B 5.4 5.43.3 5.4 H A 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 5.4 2.1 ×L 5.3 3× 2.4 2.4 2.4 3.3 (mm) 8 × 10 10 × 10 2.9 3.2 6.6 6.3 8.3 10.3 × 7.7 8 × 5.4 × 5.4 6.38.3× 5.8 6.3 5.4 6.64 × 5.46.6 5 × 5.4 5.3 1.5 6.6 6.6 1.8 6.6 8.3 2.4 2.4 3.3 5.37.7 6.6 5.4 6.6 10 106.6 8.3 0.5 to 0.8 0.5 to 0.8 0.5 to 0.84.3 0.5 to 0.8 5.3 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 6.6 1.1 C0.8 0.5 to 3.3 6.6 6.6 8.3 2.2 2.3 2.4 10.3 4.5 4.3 5.8 2.1 8.3 3.1 2.2 E 0.8 1.0 1.3 2.2 2.2 2.2 2.3 L 5.4 5.4 5.4 5.4 5.8 7.7 5.4 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0 CAT.8100D ALUMINUM  ELECTROLYTIC  CAPACITORS WT series Dimensions V Cap. (µF) 4 0G Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 0.1 0R1 4 × 5.4 (3) 1.0　 0.22 R22 4 × 5.4 (3) 2.6　 0.33 R33 4 × 5.4 (3) 3.2　 0.47 R47 4 × 5.4 (3) 3.8　 1 010 4 × 5.4 (3) 6.3 (5.9) 2.2 2R2 3 × 5.4 7.5　 3.3 3R3 3 × 5.4 9　　 4 × 5.4 14 4.7 4R7 4 × 5.4 (3) 13 (10) 4 × 5.4 15　　 5 × 5.4 19 5 × 5.4 25　　 6.3 × 5.4 30 42　　 51 (45) 10 100 22 220 4 × 5.4 22 4 × 5.4 22 5 × 5.4 27 5 × 5.4 30 6.3 × 5.4 38　　 6.3 × 5.4 33 330 5 × 5.4 30 5 × 5.4 30 5 × 5.4 35 6.3 × 5.4 40 6.3 × 5.4 48　　 47 470 5 × 5.4 36 5 × 5.4 36 6.3 × 5.4 46 6.3 × 5.4 50 8 × 5.4 100 101 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 5.4 60 150 151 6.3 × 5.8 86 6.3 × 5.8 86 6.3 × 5.8 86 6.3 × 7.7 220 221 102 (91) 102 (91) 6.3 × 7.7 105 330 331 6.3 × 7.7 105 6.3 × 7.7 105 8 × 10 470 471 8 × 10 210 8 × 10 210 680 681 8 × 10 210 8 × 10 210 1000 102 8 × 10 230 8 × 10 230 10 × 10 310 1500 152 10 × 10 310 10 × 10 310 4 × 5.4 (3) 18 (14) 8 × 5.4 8 × 5.4 5 × 5.4 23　　 4 × 5.4 (3) 11 (9) 8 × 5.4 8 × 5.4 59 (52) 6.3 × 7.7 60 66 (59) 6.3 × 5.8 63　　 6.3 × 7.7 63 6.3 × 7.7 91　　 6.3 × 7.7 84　　 8 × 10 140 95 8 × 10 140　　 8 × 10 155　 10 × 10 180 6.3 × 7.7 105 8 × 10 155　　 8 × 10 190　 10 × 10 220 195 8 × 10 195 8 × 10 190　　 10 × 10 300　 8 × 10 210 8 × 10 230 10 × 10 10 × 10 310 10 × 10 310 300　　 ( ) is also available with φ3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system. Case size Rated φ D × L (mm) ripple Rated ripple current (mArms) at 105°C 120Hz Size φ6.3 × 5.8 is available for capacitors marked. "   " In such a case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50　　 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UX(p.154), UJ(p.160) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100D