UWT0J152MNL1GS

ALUMINUM ELECTROLYTIC CAPACITORS UWT Chip Type, Wide Temperature Range Chip type operating over wide temperature range of to – 55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UWZ High Temperature Reflow UWF Low impeadance UUT Long Life UWT Smaller UZT Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 4 to 50V Rated Capacitance Range 1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 4 0.40 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 6.3 0.30 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance Resistance to soldering heat Marking 2 +0.1 –0.2 2 3 4 5 6 7 8 φD code 4 to 8 (5.4L) GB 6.3 to 10 (L 5.8) GS 9 10 11 12 13 14 1 2 3 4 5 6 7 8 Positive Taping code 9 10 11 12 13 14 Size code UWT 1 C 1 0 0 MC L 1 G B Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) Series name Type Negative φD 4 to 8 (L 7.7) 8 to 10 (L = 10) Capacitance tolerance (±20%) Rated capacitance (10µF) 1. Voltage mark for 6.3V is 6V . L±0.5 Pressure relief vent 0.5 MAX. Negative Positive φD ×L 4 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 5.4 (mm) Series name 8 × 10 10 × 10 Type A 1.8 2.1 2.4 2.4 2.4 3.3 2.9 3.2 A±0.2 E A±0.2 C±0.2 B±0.2 φD±0.5 0.3 MAX. H B 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 C 4.3 5.3 φD × L 6.6 6.6 6.6 8.3 8.3 10.3 E 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 Negative L 5.4 A 5.4 5.41.8 5.8 2.1 7.7 2.45.4 2.4 10 H H 4 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 5.4 2.4 10 C 4.3 5.3 6.6 6.6 Frequency coefficient of rated current E 1.0 1.3 ripple2.2 2.2 Frequency Coefficient L H 50 Hz 5.4 0.70 120 Hz 5.4 1.00 300 Hz 5.4 1.17 1 kHz 5.8 1.36 8 × 10 3.3 2.9 8.3 8.3 8.3 8.3 2.2 2.3 10 kHz or more 7.7 5.4 1.50　　 3.1 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 6.6 0.5 to 0.8 0.8 to 1.1 0.8 6.6 to 1.1 B 0.8 0.5 to 4.3 5.3 6.6 1. Voltage mark for 6.3V is 6V . Dimension table in next page. code CL NL Rated voltage (16V) A±0.2 E A±0.2 B±0.2 φD±0.5 Plastic platform 6.3 Configuration 2 Apply to φ6.3 × 5.8, C±0.2 φ6.3 × 7.7 0.3 MAX. Pressure relief vent A2P 100 35V Negative H 2 0.5 MAX. Plastic platform 1 L±0.5 Voltage Lot No. 50 2 3 UWT 1 C 1 0 0 MC L 1 G B A±0.2 E A±0.2 (L±0.3) L A2P 100 35V Capacitance H B±0.2 A2P 10 16V +0.1 –0.2 (L±0.3) 1 Voltage 105˚C Marking Lot No. Trade mark 35 2 3 tan δ 200% or less than the initial specified value Leakage current Less than or equal to the initial specified value 0.5 MAX. B±0.2 0.3 MAX. (φ8 × 10, φ10 × 10 ) Lot No. (φ8 × 10, φ10 × 10 ) C±0.2 2 Apply to φ6.3 × 5.8, φ6.3 × 7.7 Capacitance 105˚C Marking Trade mark 25 2 4 Within ±25% of the initial capacitance value for capacitors of 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. Capacitance change 1 Positive A±0.2 E A±0.2 Plastic platform 1 Voltage L Lot No. C±0.2 0.3 MAX. 0.5 MAX. Plastic platform φD±0.5 105˚C Marking 1 Voltage φD±0.5 Capacitance 16 2 4 Positive A2P 10 16V 5.4 ) 10 3 8 Type numbering system (Example : 16V 10µF) Chip Type (φ4 to φ8 × 5.4 ) Capacitance 6.3 4 8 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within ±10% of the initial capacitance value is maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Black print on the case top. Shelf Life 105 Marking (φ4˚Cto φ8 × 4 7 15 6.6 4 8 1 10 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UWT Dimensions Rated Voltage （V） （code） 4 （0G） 6.3 （0J） code φD GB 4 to 8 (5.4L) 3 to 10 (L 5.8) GS Taping code Size code 10 （1A） Configuration φD 4 to 8 (L 7.7) to 10 (L = 10) code CL NL (mm) 10 × 10 3.2 10.3 10.3 16 （1C） Rated Capacitance （µF） Case Size φD×L（mm） tan δ 22 4× 5.4 0.40 Leakage Current （µA） at 20℃ after 2 minutes （ ） 3 Rated Ripple （mArms） （105℃/120Hz） Part Number 22 UWT0G220MCL1GB 33 5×5.4 0.40 3 30 UWT0G330MCL1GB 47 5× 5.4 0.40 3 36 UWT0G470MCL1GB 100 6.3× 5.4 0.40 4 60 UWT0G101MCL1GB 150 6.3× 5.8 0.40 6 86 UWT0G151MCL1GS 220 8× 5.4 0.40 8.8 102 UWT0G221MCL1GB 220 6.3×5.8 0.40 8.8 91 UWT0G221MCL6GS 330 6.3× 7.7 0.40 13.2 105 UWT0G331MCL1GS 470 8× 10 0.40 18.8 210 UWT0G471MNL1GS 680 8× 10 0.40 27.2 210 UWT0G681MNL1GS 1000 8× 10 0.40 40 230 UWT0G102MNL1GS 1500 10× 10 0.40 60 310 UWT0G152MNL1GS 22 4× 5.4 0.30 3 22 UWT0J220MCL1GB 33 5× 5.4 0.30 3 30 UWT0J330MCL1GB 47 5× 5.4 0.30 3 36 UWT0J470MCL1GB 100 6.3× 5.4 0.30 6.3 60 UWT0J101MCL1GB 150 6.3× 5.8 0.30 9.45 86 UWT0J151MCL1GS 220 8× 5.4 0.30 13.86 102 UWT0J221MCL1GB 220 6.3× 5.8 0.30 13.86 91 UWT0J221MCL6GS 330 6.3× 7.7 0.30 20.79 105 UWT0J331MCL1GS 470 8× 10 0.30 29.61 210 UWT0J471MNL1GS 680 8× 10 0.30 42.84 210 UWT0J681MNL1GS 1000 8× 10 0.30 63 230 UWT0J102MNL1GS 1500 10× 10 0.30 94.5 310 UWT0J152MNL1GS 22 5× 5.4 0.24 3 27 UWT1A220MCL1GB 33 5× 5.4 0.24 3.3 35 UWT1A330MCL1GB 47 6.3× 5.4 0.24 4.7 46 UWT1A470MCL1GB 100 6.3× 5.4 0.24 10 60 UWT1A101MCL1GB 150 6.3× 5.8 0.24 15 86 UWT1A151MCL1GS 220 6.3×7.7 0.24 22 105 UWT1A221MCL1GS 330 8× 10 0.24 33 195 UWT1A331MNL1GS 470 8× 10 0.24 47 210 UWT1A471MNL1GS 680 10× 10 0.24 68 310 UWT1A681MNL1GS 1000 10× 10 0.24 100 310 UWT1A102MNL1GS 10 4× 5.4 0.20 3 18 UWT1C100MCL1GB 22 5× 5.4 0.20 3.52 30 UWT1C220MCL1GB 33 6.3× 5.4 0.20 5.28 40 UWT1C330MCL1GB 47 6.3× 5.4 0.20 100 6.3× 5.4 0.20 7.52 16 50 UWT1C470MCL1GB 60 UWT1C101MCL1GB 150 6.3× 7.7 0.20 24 95 UWT1C151MCL1GS 220 6.3× 7.7 0.20 35.2 105 UWT1C221MCL1GS 330 8× 10 0.20 52.8 195 UWT1C331MNL1GS 4.5 470 8× 10 0.20 75.2 230 UWT1C471MNL1GS 10 680 10× 10 0.20 108.8 310 UWT1C681MNL1GS .8 to 1.1 CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UWT Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 4.7 25 （1E） 50 （1H） tan δ 4×5.4 0.16 Leakage Current （µA） at 20℃ after 2 minutes （ ） 3 Rated Ripple （mArms） （105℃/120Hz） Part Number 13 UWT1E4R7MCL1GB 10 5× 5.4 0.16 3 23 UWT1E100MCL1GB 22 6.3× 5.4 0.16 5.5 38 UWT1E220MCL1GB 33 6.3×5.4 0.16 8.25 48 UWT1E330MCL1GB 47 8×5.4 0.16 11.75 66 UWT1E470MCL1GB 47 6.3×5.8 0.16 11.75 59 UWT1E470MCL6GS 100 6.3× 7.7 0.16 25 91 UWT1E101MCL1GS 150 8× 10 0.16 37.5 140 UWT1E151MNL1GS 220 8× 10 0.16 55 155 UWT1E221MNL1GS 330 8×10 0.16 82.5 190 UWT1E331MNL1GS 470 10×10 0.16 117.5 300 UWT1E471MNL1GS 4× 5.4 0.14 3 15 UWT1V4R7MCL1GB 10 5× 5.4 0.14 3.5 25 UWT1V100MCL1GB 22 6.3× 5.4 0.14 7.7 42 UWT1V220MCL1GB 33 8×5.4 0.14 11.55 59 UWT1V330MCL1GB 4.7 35 （1V） Case Size φD×L（mm） 33 6.3×5.8 0.14 11.55 52 UWT1V330MCL6GS 47 6.3×5.8 0.14 16.45 63 UWT1V470MCL1GS 100 6.3× 7.7 0.14 35 84 UWT1V101MCL1GS 150 8× 10 0.14 52.5 155 UWT1V151MNL1GS 220 8× 10 0.14 77 190 UWT1V221MNL1GS 330 10×10 0.14 115.5 300 UWT1V331MNL1GS 1 4×5.4 0.14 3 6.2 UWT1H010MCL1GB 2.2 4× 5.4 0.14 3 11 UWT1H2R2MCL1GB 3.3 4× 5.4 0.14 3 14 UWT1H3R3MCL1GB 4.7 5×5.4 0.14 3 19 UWT1H4R7MCL1GB 10 6.3×5.4 0.14 5 30 UWT1H100MCL1GB 22 8×5.4 0.14 11 51 UWT1H220MCL1GB 22 6.3×5.8 0.14 11 45 UWT1H220MCL6GS 33 6.3×7.7 0.14 16.5 60 UWT1H330MCL1GS 47 6.3× 7.7 0.14 23.5 63 UWT1H470MCL1GS 100 8×10 0.14 50 140 UWT1H101MNL1GS 150 10 ×10 0.14 75 180 UWT1H151MNL1GS 220 10 ×10 0.14 110 220 UWT1H221MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. Please select UUX, UUJ series if high C/V products are required. CAT.8100K