UWT1E471MNL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UWT Chip Type, Wide Temperature Range Chip type operating over wide temperature range of to – 55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UWZ High Temperature Reflow UWF Low impeadance UUT Long Life UWT Smaller UZT Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 4 to 50V Rated Capacitance Range 1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 4 0.40 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 6.3 0.30 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance Resistance to soldering heat Marking Chip Type (φ4 to φ8 × 5.4 ) Positive Lot No. H (φ8 × 10, φ10 × 10 ) 50 2 3 0.5 MAX. 0.5 MAX. B±0.2 Negative B±0.2 L±0.5 Pressure relief vent 4 5 6 1 7 8 2 9 10 11 12 13 14 3 4 5 6 7 8 φD code 4 to 8 (5.4L) GB 6.3 to 10 (L 5.8) GS 9 10 11 12 13 14 UWT 1 C 1 0 0 MC L 1 G B 6.3 Package code Size code φD Configuration 4 to 10 φD code 4 to 8 (L 7.7) CL Rated capacitance (10µF) 8 to 10 (L tolerance = 10) NL (±20%) Capacitance Rated voltage (16V) Capacitance tolerance (±20%) Series name Rated capacitance (10µF) Type Rated voltage (16V) code 1 Configuration φD 4 to 8 (L 7.7) 8 to 10 (L = 10) code CL NL Series name H φD±0.5 A2P 100 35V 1. Voltage mark for 6.3V is 6V . 3 Positive C±0.2 0.3 MAX. Pressure relief vent 2 Positive A±0.2 E A±0.2 φD±0.5 A2P 100 35V C±0.2 Plastic platform 1 Voltage 1 Negative 2 0.3 MAX. L±0.5 Lot No. 35 2 3 UWT 1 C 1 0 0 MC L 1 G B H Plastic platform Capacitance Lot No. A±0.2 E A±0.2 Negative 2 2 Apply to φ6.3 × 5.8, φ6.3 × 7.7 1 10Voltage ) Positive A±0.2 E A±0.2 +0.1 –0.2 (L±0.3) Capacitance 105˚C Marking Trade mark C±0.2 +0.1 2 Apply to φ6.3 L × 5.8, –0.2φ6.3 × 7.7 × 25 2 4 tan δ 200% or less than the initial specified value Leakage current Less than or equal to the initial specified value Type (mm) 0.5 MAX. L (L±0.3) 105˚C Marking (φ8 ×mark 10, φ10 Trade 16 2 4 Within ±25% of the initial capacitance value for capacitors of 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. Capacitance change φD A±0.2 E A±0.2 Lot No. C±0.2 B±0.2 φD±0.5 A2P 10 16V 10 16V A2P 105˚C Marking φD±0.5 Plastic platform 1 0.3 MAX. Voltage 0.3 MAX. 0.5 MAX. Plastic platform B±0.2 1 Voltage 105˚C Marking 10 3 8 Type numbering system (Example : 16V 10µF) (φ4 to φ8 × 5.4 ) Capacitance 6.3 4 8 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within ±10% of the initial capacitance value is maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Black print on the case top. Shelf Life Capacitance 4 7 15 H Negative 1. Voltage mark for 6.3V is 6V . 128 4 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 5.4 A 1.8 2.1 B 4.3 φD × L 5.3 6.6 4× C 4.3 5.3 E 1.0 1.3 2.2 2.2 L 5.4 B 5.4 5.44.3 5.8 H Dimension table in next page. ×L A 2.4 2.4 2.4 3.3 8 × 10 10 × 10 2.9 3.2 8.35.8 6.3 10.3 × 7.7 8 × 5.4 5.4 6.65 × 5.46.66.3 × 8.3 5.4 6.3 × 6.6 1.8 6.6 6.6 2.1 2.2 5.3 7.7 8.3 8.3 2.4 2.4 6.65.4 6.6 10 2.3 3.1 8 × 10 2.4 3.3 2.9 6.6 10 8.3 8.3 8.3 8.3 4.5 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 6.6 0.5 to 0.8 0.8 to 1.1 0.8 6.6 to 1.1 C 0.8 0.5 to 4.3 5.3 6.6 E 1.0 1.3 2.2 2.2 2.2 2.3 3.1 L 5.4 5.4 5.4 5.8 7.7 5.4 10 H 1 10.3 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0. ALUMINUM  ELECTROLYTIC  CAPACITORS UWT Dimensions V 1 010 50 1H 4 × 5.4 2.2 2R2 4 × 5.4 3.3 3R3 4.7 4R7 Cap. (µF) 4 0G Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 10 100 22 220 4 × 5.4 22 4 × 5.4 22 5 × 5.4 33 330 5 × 5.4 30 5 × 5.4 30 5 × 5.4 47 470 5 × 5.4 36 5 × 5.4 36 6.3 × 5.4 100 101 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 5.4 150 151 6.3 × 5.8 86 6.3 × 5.8 86 6.3 × 5.8 220 221 102 (91) 330 331 6.3 × 7.7 105 6.3 × 7.7 105 8 × 10 195 470 471 8 × 10 210 8 × 10 210 8 × 10 680 681 8 × 10 210 8 × 10 210 10 × 10 1000 102 8 × 10 230 8 × 10 230 10 × 10 310 1500 152 10 × 10 310 10 × 10 310 4 × 5.4 15　　 5 × 5.4 23　　 5 × 5.4 25　　 6.3 × 5.4 30 8 × 5.4 8 × 5.4 18 27 5 × 5.4 30 6.3 × 5.4 38　　 6.3 × 5.4 42　　 35 6.3 × 5.4 40 6.3 × 5.4 48　　 8 × 5.4 59 (52) 46 6.3 × 5.4 50 8 × 5.4 66 (59) 6.3 × 5.8 60 6.3 × 5.4 60 6.3 × 7.7 91　　 6.3 × 7.7 8 × 10 140 86 6.3 × 7.7 95 8 × 10 140　　 8 × 10 155　 10 × 10 180 6.3 × 7.7 105 8 × 10 155　　 8 × 10 190　 10 × 10 220 190　　 10 × 10 300　 102 (91) 6.3 × 7.7 105 8 × 10 195 8 × 10 210 8 × 10 230 10 × 10 310 10 × 10 310 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 8 × 5.4 51 (45) 6.3 × 7.7 60 63　　 6.3 × 7.7 63 84　　 300　　 Rated Case size φ D × L (mm) ripple Frequency coefficient of rated ripple current 50 Hz 0.70 5 × 5.4 19 4 × 5.4 Size φ6.3 × 5.8 is available for capacitors marked. "   " In such a case, 6 will be put at 12th digit of type numbering system. Frequency Coefficient 4 × 5.4 14 13　　 4 × 5.4 6.3 11 10 kHz or more 1.50　　 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UUX(p.170), UUJ(p.176) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. 129 Rated ripple current (mArms) at 105°C 120Hz