UWT1V330MNL

ALUMINUM ELECTROLYTIC CAPACITORS WT Chip Type, Wide Temperature Range series Chip type operating over wide temperature range of to – 55 ~ +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WZ High Temperature Reflow WF UT Low impeadance WT Smaller Long Life ZT Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Performance Characteristics – 55 ~ +105°C 4 ~ 50V 0.1 ~ 1500µF ±20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ (MAX.) 4 0.40 6.3 0.30 4 7 15 10 0.24 6.3 4 8 16 0.20 10 3 8 25 0.16 16 2 4 25 2 4 35 0.14 35 2 3 50 0.14 50 2 3 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.) Endurance After 1000 hours' application of rated voltage at 105°C, capacitors meet the characteristic requirements listed at right. Within ±25% of initial value for capacitors of φ3mm unit, and 16V or less. Within ±20% of initial value for capacitors of 25V or more. tan δ 200% or less of initial specified value Leakage current Initial specified value or less Capacitance change Shelf Life Resistance to soldering heat Marking After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Initial specified value or less Leakage current listed at right. Black print on the case top. Chip Type Type numbering system (Example : 16V 10µF) Positive C±0.2 0.5 MAX. 1 Voltage D±0.5 Plastic platform 0.3 MAX. B±0.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 fD code 3 ~ 8 (5.4L) GB 6.3 ~ 10 (L 5.8) GS Package code Size code fD code Configuration 3 2 fD code 4 ~ 10 1 3 ~ 8 (L 7.7) CL 8 ~ 10 (L = 10) NL (f3 ~ f8 ´ 5.4 ) Capacitance 105¡C Marking UWT 1 C 1 0 0 MC L 1 G B A±0.2 A±0.2 Capacitance tolerance (±20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Type A2P 10 16V f Lot No. 2 L +0.1 Ð0.2 (L±0.3) 3 H 3 Apply to f6.3 ´ 5.8, f6.3 ´ 7.7 Capacitance 105¡C Marking Trade mark (f8 ´ 10, f10 ´ 10 ) 1 Voltage D±0.5 C±0.2 0.5 MAX. Plastic platform 0.3 MAX. B±0.2 E Negative Positive f D´L (mm) 3 ´ 5.4 4 ´ 5.4 5 ´ 5.4 6.3 ´ 5.4 6.3 ´ 5.8 6.3 ´ 7.7 8 ´ 5.4 8 ´ 10 10 ´ 10 1.5 3.3 3.3 0.8 5.4 0.5 ~ 0.8 1.8 4.3 4.3 1.0 5.4 0.5 ~ 0.8 2.1 5.3 5.3 1.3 5.4 0.5 ~ 0.8 2.4 6.6 6.6 2.2 5.4 0.5 ~ 0.8 2.4 6.6 6.6 2.2 5.8 0.5 ~ 0.8 2.4 6.6 6.6 2.2 7.7 0.5 ~ 0.8 3.3 8.3 8.3 2.3 5.4 0.5 ~ 0.8 2.9 8.3 8.3 3.1 10 0.8 ~ 1.1 3.2 10.3 10.3 4.5 10 0.8 ~ 1.1 A±0.2 A±0.2 Lot No. L±0.5 Pressure relief vent H Negative 1. Voltage mark for 6.3V is 6V . In case of marking for f3 units, ÒVÓ for rated voltage is omitted. 2. In case of marking for f3 units. Lot No is expressed by a digit (month code). A B C E L H A2P 100 35V Dimension table in next page. f E CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS WT Cap. (µF) series Dimensions V Code 4 0G 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 4 × 5.4 (3) 4 × 5.4 (3) 4 × 5.4 (3) 4 × 5.4 (3) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 4 × 5.4 5 × 5.4 5 × 5.4 22 30 36 60 86 102 (91) 105 210 210 230 310 4 × 5.4 5 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 8 × 5.4 6.3 × 7.7 8 × 10 8 × 10 8 × 10 10 × 10 22 30 36 60 86 105 210 210 230 310 5 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.4 6.3 × 5.8 8 × 10 8 × 10 10 × 10 10 × 10 27 35 46 60 86 105 195 210 310 310 4 × 5.4 (3) 18 (14) 5 × 5.4 6.3 × 5.4 6.3 × 5.4 6.3 × 5.4 6.3 × 7.7 6.3 × 7.7 8 × 10 8 × 10 10 × 10 30 40 50 60 95 105 195 230 310 4 × 5.4 (3) 13 (10) 5 × 5.4 6.3 × 5.4 6.3 × 5.4 8 × 5.4 6.3 × 7.7 8 × 10 8 × 10 8 × 10 10 × 10 23 38 48 91 140 155 190 300 3 × 5.4 3 × 5.4 4 × 5.4 5 × 5.4 6.3 × 5.4 8 × 5.4 6.3 × 7.7 8 × 10 8 × 10 10 × 10 7.5 9 15 25 42 63 84 155 190 300 1.0 2.6 3.2 3.8 4 × 5.4 (3) 6.3 (5.9) 4 × 5.4 (3) 11 (9) 4 × 5.4 5 × 5.4 6.3 × 5.4 8 × 5.4 6.3 × 7.7 8 × 10 10 × 10 10 × 10 14 19 30 51 (45) 60 63 140 180 220 59 (52) 6.3 × 7.7 66 (59) 6.3 × 5.8 101 6.3 × 5.4 151 6.3 × 5.8 221 471 681 102 152 8 × 5.4 8 × 10 8 × 10 8 × 10 10 × 10 331 6.3 × 7.7 102 (91) 6.3 × 7.7 Case size Rated φ D × L (mm) ripple Rated Ripple (mArms) at 105°C 120Hz ( ) is also available with φ3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system. Size φ6.3 × 5.8 is available for capacitors marked. " " In such a case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UX(p.74), UJ(p.76) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V