UWX1E220MCL1GB

ALUMINUM  ELECTROLYTIC  CAPACITORS UWX 5.5mmL Chip Type Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Load life of 2000 hours at 85°C. UWT Compliant to the RoHS directive (2011/65/EU). UWJ High Temperature High Temp reflow UWX UWP Bi-polarized Smaller Specifications UZS Item Performance Characteristics Category Temperature Range –40 to +85°C Rated Voltage Range 4 to 50V Rated Capacitance Range 1 to 330µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater. Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 6.3 10 0.35 (0.40) 0.26 (0.30) 0.20 (0.24) 4 7 15 Rated voltage (V) Z– 25°C / Z+20°C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Measurement frequency : 120Hz at 20°C 16 25 35 50 4 Z– 40°C / Z+20°C 0.16 (0.19) 6.3 4 8 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) Values in ( ) applicable to WR, φ3 case size. Measurement frequency : 120Hz 35 25 16 50 2 2 2 2 3 4 4 3 10 3 8 Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C. Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Chip Type Plastic platform 0.3 MAX. 0.3 MAX. 5.4 5.4 +0.1 –0.2 +0.1 –0.2 1 C±0.2 C0.2 0.5 to 0.8 2 3 4 5 6 7 8 φD A φD BA C B E C 3 1.5 3 3.3 1.5 3.3 3.3 0.8 3.3 4 1.8 4 4.3 1.8 4.3 4.3 1.0 4.3 5 2.1 5 5.3 2.1 5.3 5.3 1.3 5.3 11 12 13 14 Taping code Taping code Size code Configuration Capacitance toleranc (20%) Capacitance tolerance (±20%) Rated capacitance (10F) RatedRated capacitance voltage(10µF) (16V) Negative 0.5 to 0.8 9 10 Configuration A0.2 A0.2 1 Voltage 0.5 MAX. 0.5 MAX. E E A±0.2 A±0.2 2 Lot No. Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value 2 X 3 1 4 C 5 1 6 0 7 0 8 M 9 C 10 L 11 1 12 G 13 B 14 U1 W UWX 1 C 1 0 0 MC L 1 G B Positive B0.2B±0.2 Plastic platform φD±0.5 φD0.5 1 Voltage X2A2 10 10 16V 16V Capacitance 2 Lot No. Capacitance change tan δ Leakage current Type numbering system (Example : 16V 10µF) Positive Capacitance Within ±20% of the initial capacitance value (Within ±25% for 4 V and φ3,WR series units) 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage Current φD Size code Code 3 φD 4 to 38 2 Code 12 4 to 8 1 Rated Series voltagename (16V) Negative (mm) 6.3 (mm) 8 2.4 6.3 3.3 8 6.6 2.4 8.3 3.3 6.6 8.3 6.6 8.3 2.2 6.6 2.3 8.3 Series name Type Type • In the case of size φ3 in ( ),parentheses, use WX in the 2nd and 3rd 2 digit and put a in the 12th digit of type numbering system. 1. Voltage mark for 6.3V is 6V . E 0.8 1.0 1.3 2.2 2.3 In case of marking for φ3 units, “V” for rated voltage is omitted. 1. Voltage mark for 6.3V is 6V . 2. In case of marking for φ3 units, Lot No.is expressed by a digit (month code). In case of marking for φ3 units, “V” for rated voltage is omitted. 2. In case of marking for φ3 units, Lot No.is expressed by a digit (month code). Dimension table in next page. 110 ALUMINUM  ELECTROLYTIC  CAPACITORS UWX Dimensions 4 0G V Cap. (µF) Code 1 010 2.2 2R2 3.3 3R3 4.7 4R7 6.3 0J 10 1A 16 1C 25 1E 35 1V 3 8.4 4 (3) 13 (10) 3 10 4 17 4 (3) 16 (12) 4 18 5 20 (18) 　 4 (3) 23 (18) 5 27 (24) 5 29 (24) 6.3 33 (30) 33 (30) 5 37 (30) 6.3 42 (38) 6.3 46 (39) 8 52 (43) 5 41 (34) 6.3 49 (44) 6.3 52 (46) 8 62 (53) 8 71 45 (40) 6.3 52 (47) 6.3 58 (52) 8 70 (60) 8 80 6.3 52 (46) 6.3 57 (50) 6.3 63 (57) 8 6.3 70 (47) 6.3 76 (54) 6.3 86 8 10 100 22 220 3 019 4 (3) 28 (21) 5 33 330 4 028 5 37 (34) 47 470 4 033 5 56 560 5 042 100 101 5 056 150 151 6.3 079 6.3 71 8 111 (76) 220 221 6.3 096 8 110 (74) 8 135 330 331 8 145 8 170 76 (65) 110 ( ) is also available with φ3mm upon request. • In the case of size φ3 in ( ),parentheses, use WX at 2nd and 3rd digit and put 2 at the 12th digit of type numbering system. Size φ4 is available for capacitors marked. " " Size φ5 is available for capacitors marked. " " Size φ6.3 is available for capacitors marked. " " } 50 Hz 0.70 120 Hz 1.00 Case size Rated φ D (mm) ripple Rated ripple current (mArms) at 85°C 120Hz ( ) = φ3 units and UWR In such a case, W R will be put at 2nd and 3rd digit of type numbering system. Frequency coefficient of rated ripple current Frequency Coefficient 50 1H 4 (3) 8.4(8.0) 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50　　 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UUR(p.154), UUG(p.160) if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. 111