UWZ1V100MCL1GB

ALUMINUM  ELECTROLYTIC  CAPACITORS UWZ Chip Type, Wide Temperature Range High Temperature (260°C) Reflow Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec 230°C over 60 sec 2 times  (φ8 × 6.2, φ10 × 10 : 1 time) Chip type operating over wide temperature range of to –55 to +105°C. UWZ Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. High Temperature Reflow UWT Specifications Performance Characteristics Item Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.30 Rated voltage (V) tan δ (max.) Tangent of loss angle (tan δ) 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z(– 25°C) / Z(+20°C) Impedance ratio Stability at Low Temperature ZT / Z20 (max.) Z(– 40°C) / Z(+20°C) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Within ±25% of the initial capacitance value for capacitors of 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. 200% or less than the initial specified value tan δ Leakage current Less than or equal to the initial specified value Capacitance change After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Black print on the case top. Shelf Life Resistance to soldering heat Marking ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Type numbering system (Example : 6.3V 33µF) Chip Type (φ4 to φ6.3 ) 0.5 max. (L±0.3) L B±0.2 Capacitance C±0.2 B±0.2 A2 220j WZ A2 220j WZ φD±0.5 φD±0.5 Series Trade mark Negative Capacitance 0.3 max. B±0.2 A2 220E WZ Capacitance φD±0.5 φD±0.5 Series Trade mark L±0.5 H L±0.5 Lot No. C±0.2 B±0.2 A2 220E WZ Plastic platform Capacitance Dimension table in next page. Positive 6 7 8 9 φD code 4 to 6.3 (5.4L) GB 6.3 to 10 (L 5.8L) GS φD 4 to 6.3 (5.4L) Taping code 6.3 to 10 (L 5.8L) 10 11 12 13 14 8 × 10 10 × 10 (mm) 1.8 4.3 V 6.3 Code j 5.3 5.3 2.1 6.6 2.4 6.6 6.6 2.4 6.6 6.6 6.6 2.4 8.3 8.3 3.3 8.3 8.3 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 10 16 25 35 50 A C E V H H Negative code GB GS Type 10.3 2.9 3.2 10.3 4.3 B 5.3 6.6 6.6 6.6 8.3 8.3 10.3 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 4.3 C 5.3 6.6 6.6 6.6 8.3 8.3 10.3 5.4 5.4 5.4 5.8 7.7 6.2 10 10 1.0 E 1.3 2.2 2.2 2.2 2.3 3.1 4.5 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 5.4 5.4 5.4 5.8 7.7 6.2 10 10 L 4.3 Voltage H 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 6.2 ×L 1.8 4 × 5.4 2.1 5 × 5.4 2.46.3 × 5.4 2.46.3 × 5.8 2.46.3 × 7.7 3.3 8 × 6.2 2.9 8 × 103.2 10 × 10 A H Negative 4 × 5.4 B L 0.5 max. Voltage (E:25V) 5 φD E C±0.2 0.3 max. Trade mark 4 A C Negative Plastic platform (φ8 × 10, φ10×10) Series 3 ×L Positive Voltage (E:25V) Lot No. φD A±0.2 E A±0.2 (φ8 × 10, φ10×10) 2 Configuration Taping code Capacitance tolerance (±20%) Configuration Rated capacitance (33µF) Capacitance tolerance (±20%) Rated voltage (6.3V) Rated capacitance (33µF) Series name Rated voltage (6.3V) Type Series name H L±0.3 Lot No. 10 11 12 13 14 (mm) H L±0.3 9 Positive 0.5 max. Lot No. 0.5 max. Plastic platform 0.3 max. 8 Positive C±0.2 0.3 max. Voltage ( j:6.3V) 7 Negative 1 Series 6 Negative Plastic platform (φ8 × 6.2 ) Trade mark 5 H 1 Apply to φ6.3 × 5.8, φ6.3 × 7.7 Voltage ( j:6.3V) 0.5 max. B±0.2 1 Apply to φ6.3 × 5.8,+0.1 φ6.3 × 7.7 (L±0.3) L –0.2 4 UWZ 0 J 3 3 0 M C L 1G B 0.5 max. Capacitance H 1 A±0.2 E A±0.2 Lot No. +0.1 –0.2 3 1 A±0.2 E A±0.2 Capacitance C±0.2 B±0.2 φD±0.5 φD±0.5 A2 33C WZ A2 33C WZ (φ8 × 6.2 ) 0.3 max. 2 UWZ 0 J 3 3 0 M C L 1G B A±0.2 E A±0.2 Plastic platform Series Voltage (C:16V) Positive A±0.2 E A±0.2 C±0.2 0.3 max. A±0.2 E A±0.2 (φ4 to φ6.3 ) Series Voltage (C:16V) Lot No. 1 Positive Plastic platform Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50　　 CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UWZ Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） Rated Capacitance （µF） Case Size φD×L（mm） tan δ 22 4× 5.4 0.30 （ ） 3 Rated Ripple （mArms） （105℃/120Hz） Part Number 22 UWZ0J220MCL1GB 33 5× 5.4 0.30 3 30 UWZ0J330MCL1GB 47 5×5.4 0.30 3 36 UWZ0J470MCL1GB 100 6.3× 5.4 0.30 6.3 60 UWZ0J101MCL1GB 150 6.3× 5.8 0.30 9.45 86 UWZ0J151MCL1GS 220 8× 6.2 0.30 13.86 102 UWZ0J221MCL1GS 330 6.3× 7.7 0.30 20.79 105 UWZ0J331MCL1GS 470 8× 10 0.30 29.61 210 UWZ0J471MCL1GS 680 8× 10 0.30 42.84 210 UWZ0J681MCL1GS 1000 10×10 0.30 63 230 UWZ0J102MCL1GS 1500 10× 10 0.30 94.5 310 UWZ0J152MCL1GS 22 5× 5.4 0.24 3 27 UWZ1A220MCL1GB 33 5× 5.4 0.24 3.3 35 UWZ1A330MCL1GB 47 6.3× 5.4 0.24 4.7 46 UWZ1A470MCL1GB 100 6.3× 5.4 0.24 10 60 UWZ1A101MCL1GB 150 6.3× 5.8 0.24 15 86 UWZ1A151MCL1GS 220 6.3×7.7 0.24 22 105 UWZ1A221MCL1GS 330 8× 10 0.24 33 195 UWZ1A331MCL1GS 470 8× 10 0.24 47 210 UWZ1A471MCL1GS 680 10× 10 0.24 68 310 UWZ1A681MCL1GS 1000 10× 10 0.24 100 310 UWZ1A102MCL1GS 10 4× 5.4 0.20 3 18 UWZ1C100MCL1GB 22 5× 5.4 0.20 3.52 30 UWZ1C220MCL1GB 33 6.3×5.4 0.20 5.28 40 UWZ1C330MCL1GB 47 6.3× 5.4 0.20 50 UWZ1C470MCL1GB 100 6.3× 5.4 0.20 16 60 UWZ1C101MCL1GB 150 6.3× 7.7 0.20 24 95 UWZ1C151MCL1GS 220 6.3× 7.7 0.20 35.2 105 UWZ1C221MCL1GS 330 8×10 0.20 52.8 195 UWZ1C331MCL1GS 7.52 470 8× 10 0.20 75.2 210 UWZ1C471MCL1GS 680 10× 10 0.20 108.8 310 UWZ1C681MCL1GS 4× 5.4 0.16 3 13 UWZ1E4R7MCL1GB 4.7 25 （1E） Leakage Current （µA） at 20℃ after 2 minutes 10 5× 5.4 0.16 3 23 UWZ1E100MCL1GB 22 6.3×5.4 0.16 5.5 38 UWZ1E220MCL1GB 33 6.3× 5.4 0.16 8.25 48 UWZ1E330MCL1GB 47 8× 6.2 0.16 11.75 66 UWZ1E470MCL1GS 100 6.3× 7.7 0.16 25 91 UWZ1E101MCL1GS 150 8× 10 0.16 37.5 140 UWZ1E151MCL1GS 220 8×10 0.16 55 155 UWZ1E221MCL1GS 330 10× 10 0.16 82.5 190 UWZ1E331MCL1GS 470 10× 10 0.16 117.5 300 UWZ1E471MCL1GS CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UWZ Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 4.7 35 （1V） tan δ 4×5.4 0.14 Leakage Current （µA） at 20℃ after 2 minutes Rated Ripple （mArms） （105℃/120Hz） Part Number 3 15 UWZ1V4R7MCL1GB （ ） 10 5×5.4 0.14 3.5 25 UWZ1V100MCL1GB 22 6.3×5.4 0.14 7.7 42 UWZ1V220MCL1GB 33 8×6.2 0.14 11.55 59 UWZ1V330MCL1GS 47 6.3×5.8 0.14 16.45 63 UWZ1V470MCL1GS 100 6.3×7.7 0.14 35 84 UWZ1V101MCL1GS 150 8× 10 0.14 52.5 155 UWZ1V151MCL1GS 220 10×10 0.14 77 190 UWZ1V221MCL1GS 330 10×10 0.14 115.5 300 UWZ1V331MCL1GS 1 4× 5.4 0.14 3 2.2 4× 5.4 0.14 3 6.3 11 UWZ1H010MCL1GB UWZ1H2R2MCL1GB 3.3 4× 5.4 0.14 3 14 UWZ1H3R3MCL1GB 4.7 5×5.4 0.14 3 19 UWZ1H4R7MCL1GB 6.3×5.4 0.14 5 30 UWZ1H100MCL1GB 10 50 （1H） Case Size φD×L（mm） 22 8×6.2 0.14 11 51 UWZ1H220MCL1GS 33 6.3×7.7 0.14 16.5 60 UWZ1H330MCL1GS 47 6.3×7.7 0.14 23.5 63 UWZ1H470MCL1GS 100 8×10 0.14 50 140 UWZ1H101MCL1GS 150 10 ×10 0.14 75 180 UWZ1H151MCL1GS 220 10 ×10 0.14 110 220 UWZ1H221MCL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100L