UWZ1V101MCL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UWZ Chip Type, Wide Temperature Range High Temperature (260°C) Reflow Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec 230°C over 60 sec 2 times  (φ8 × 6.2, φ10 × 10 : 1 time) Chip type operating over wide temperature range of to – 55 to +105°C. UWZ Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). High Temperature Reflow UWT Specifications Performance Characteristics Item Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.30 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance Resistance to soldering heat Marking Chip Type B±0.2 H +0.1 –0.2 H H L±0.3 Within ±25% of the initial capacitance value for capacitors of 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. 200% or less than the initial specified value tan δ Leakage current Less than or equal to the initial specified value 0.5 MAX. 2 1 3 L±0.5 H 5 4 6 5 7 6 8 7 9 8 10 11 12 13 14 9 10 11 12 13 14 φD code φD 4 to 6.3 (5.4L) GB 4 to 6.3 (5.4L) 6.3 to 10 (L 5.8L) GS 6.3 to 10 (L 5.8L) φD ×L A B Positive E 0.5 MAX. 0.5 MAX. C±0.2 L Negative Negative code GB GS Package code Package code Configuration Configuration Capacitance tolerance (±20%) Capacitance tolerance (±20%) Rated capacitance (33µF) Rated capacitance (33µF) Rated voltage (6.3V) Rated voltage (6.3V) Series name Series name Type Type Negative Negative A±0.2 E A±0.2 B±0.2 H 3 Positive A±0.2 E A±0.2 L±0.5 Capacitance Lot No. Capacitance C±0.2 B±0.2 φD±0.5 Series Plastic platform Plastic platform 0.3 MAX. 0.3 MAX. 4 2 (mm) Positive φD±0.5 A2 220E WZ A2 220E WZ 1 U WUZW0Z J 0 3J 3303M0 CM LC1LG1BG B C Voltage (E:25V) Voltage (E:25V) Series Positive 0.5 MAX. A±0.2 E A±0.2 H (φ8 ×(φ8 10, ×φ10×10) 10, φ10×10) Lot No. 50 2 3 Capacitance change A±0.2 E A±0.2 L±0.3 C±0.2 B±0.2 B±0.2 φD±0.5 φD±0.5 Series A2 220j WZ A2 220j WZ Series C±0.2 0.5 MAX. Positive Plastic platform Plastic platform 0.3 MAX. 0.3 MAX. Capacitance Lot No. Capacitance Trade mark Trade mark 35 2 3 Negative Negative 1 1 Apply to φ6.3 × 5.8, φ6.3 × 7.7 1 Apply to φ6.3 × 5.8, φ6.3 × 7.7 (φ8 ×(φ8 6.2 ×) 6.2 ) Voltage ( j:6.3V) Voltage ( j:6.3V) Lot No. 25 2 4 A±0.2 E A±0.2 (L±0.3) L +0.1 –0.2 (L±0.3) L 1 C±0.2 A±0.2 E A±0.2 C±0.2 B±0.2 φD±0.5 φD±0.5 Series A2 33C WZ A2 33C WZ Series Plastic platform Plastic platform 0.3 MAX. 0.3 MAX. 0.5 MAX. Positive Capacitance Lot No. Capacitance Trade mark Trade mark 16 2 4 Type numbering system (Example : 6.3V 33µF) (φ4 to(φ4 φ6.3 to )φ6.3 ) Lot No. 10 3 8 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Black print on the case top. Shelf Life Voltage (C:16V) Voltage (C:16V) 6.3 4 8 H 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 4 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 1.8 A 4.3 B 4.3 C 1.0 E 5.4 L 1.8 4.3 4.3 1.0 5.4 2.1 5.3 5.3 1.3 5.4 2.1 5.3 5.3 1.3 5.4 2.4 6.6 6.6 2.2 5.4 2.4 6.6 6.6 2.2 5.4 2.4 6.6 6.6 2.2 5.8 V Code Dimension table in next page. 116 2.4 6.6 6.6 2.2 5.8 2.4 6.6 6.6 2.2 7.7 2.4 6.6 6.6 2.2 7.7 3.3 8.3 8.3 2.3 6.2 3.3 8.3 8.3 2.3 6.2 2.9 2.9 3.2 3.2 8.3 10.3 8.3 10.3 8.3 10.3 8.3 10.3 3.1 10 3.1 10 4.5 10 4.5 10 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Voltage (mm) φD4××L5.4 6.3 10 16 25 35 50 j A C E V H ALUMINUM  ELECTROLYTIC  CAPACITORS UWZ Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 1 010 4 × 5.4 2.2 2R2 4 × 5.4 11 3.3 3R3 4 × 5.4 14 4.7 4R7 10 100 22 220 4 × 5.4 22 5 × 5.4 33 330 5 × 5.4 30 5 × 5.4 47 470 5 × 5.4 36 100 101 6.3 × 5.4 60 150 151 6.3 × 5.8 220 221 8 × 6.2 330 331 6.3 × 7.7 470 471 680 681 1000 1500 6.3 4 × 5.4 13 4 × 5.4 15 5 × 5.4 19 18 5 × 5.4 23 5 × 5.4 25 6.3 × 5.4 30 4 × 5.4 27 5 × 5.4 30 6.3 × 5.4 38 6.3 × 5.4 42 8 × 6.2 51 35 6.3 × 5.4 40 6.3 × 5.4 48 8 × 6.2 59 6.3 × 7.7 60 6.3 × 5.4 46 6.3 × 5.4 50 8 × 6.2 66 6.3 × 5.8 63 6.3 × 7.7 63 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 7.7 91 6.3 × 7.7 84 8 × 10 140 86 6.3 × 5.8 86 6.3 × 7.7 95 8 × 10 140 8 × 10 155 10 × 10 180 102 6.3 × 7.7 105 6.3 × 7.7 105 8 × 10 155 10 × 10 190 10 × 10 220 105 8 × 10 195 8 × 10 195 10 × 10 190 10 × 10 300 8 × 10 210 8 × 10 210 8 × 10 210 10 × 10 300 8 × 10 210 10 × 10 310 10 × 10 310 102 10 × 10 230 10 × 10 310 152 10 × 10 310 Case size φ D × L (mm) Rated ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50　　 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 117