UZD0G470MCL1GB

ALUMINUM  ELECTROLYTIC  CAPACITORS ZD 3.0mmL Chip Type series Chip type with 3.0mmL height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). ZR Smaller Products which are scheduled to be discontinued. Not recommended for new designs ZD Specifications Item Performance Characteristics Category Temperature Range – 40 to +85°C Rated Voltage Range 4 to 25V Rated Capacitance Range 2.2 to 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Rated voltage (V) 6.3 10 16 25 0.40 0.30 0.24 0.19 Rated voltage (V) 4 6.3 10 16 25 Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) Z–40°C / Z+20°C 7 4 3 2 2 15 8 8 4 4 tan δ (MAX.) Stability at Low Temperature 120Hz 20°C 4 0.50 Tangent of loss angle (tan δ) 120Hz Capacitance change tan δ Leakage current Within ±30% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C. Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Chip Type Capacitance change tan δ Leakage current Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 16V 10µF) Voltage (C : 16V) Plastic platform 0.3 MAX. V Code Negative 0.5 to 0.8 Voltage 4 6.3 10 16 25 g j A C E 2 3 4 5 6 7 8 9 10 11 12 13 14 Taping code A±0.3 3.0 +0.2 –0.1 Capacitance 1 U Z D 1 C 1 0 0 MC L 1 GB E B±0.2 D±0.5 A2 10C ZD C±0.2 A±0.3 Series Lot No. 0.5 MAX. Positive φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 Configuration (mm) 6.3 2.4 6.6 6.6 2.2 Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) Series name Type Dimensions 4 0G V Cap. (μF) 2.2 3.3 4.7 5.6 6.8 10 22 33 47 100 Code 2R2 3R3 4R7 5R6 6R8 100 220 330 470 101 4 5 5 6.3 6.3 0J 20 28 33 56 5 5 6.3 6.3 10 1A 28 37 45 70 5 6.3 16 1C 33 41 5 6.3 25 1E 23 37 4 4 4 5 5 6.3 7 11 16 18 20 27 Case size Rated φ D (mm) ripple Rated ripple current (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size soldering by reflow are given in page 18,19. Please refer to page 3 for the minimum order quantity. CAT.8100D