UZE1H220MCL

ALUMINUM ELECTROLYTIC CAPACITORS ZE 3.95mmL MAX. Chip Type, Bi-polarized series Chip type with 3.95mmL MAX, height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). ZP Smaller ZE Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Performance Characteristics – 40 ~ +85°C 6.3 ~ 50V 0.1 ~ 47µF ±20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA) , whichever is greater. R ated voltage (V) tan δ (MAX.) 6.3 0.30 Measurement frequency : 120Hz, Temperature : 20°C 10 16 25 35 50 0.24 0.20 0.18 0.16 0.16 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Eudurance Shelf Life Resistance to soldering heat Marking After 1000 hours' application of rated voltage Capacitance change Within ±30% of initial value at 85°C with the polarity inverted every 250 tan δ 300% or less of initial specified value hours, capacitors meet the characteristic Initial specified value or less Leakage current requirements listed at right. After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature,they meet the characteristic requirements Initial specified value or less Leakage current listed at right. Black print on the case top. Chip Type Voltage (C : 16V) Lot No. Series Plastic platform 0.3 MAX. C ± 0.2 0.5 MAX. Type numbering system (Example : 16V 10µF) 1 A ± 0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 U Z E 1 C 1 0 0 MC L 1 GB Taping code φD ± 0.5 X2 10C ZE B ± 0.2 E Capacitance 3.90 +0.05 – 0.2 0.5 ~ 0.8 Voltage V Code 6.3 j 10 A 16 C 25 E 35 V 50 H φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 2.4 6.6 6.6 2.2 A ± 0.2 Configuration Capacitance tolerance (± 20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Type Dimensions V Cap. (µF) Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 4 4 4 4 4 5 5 6.3 50 1H 1.0 2.0 2.8 4.0 8.4 13 17 20 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 5 6.3 6.3 28 37 45 4 6.3 6.3 17 33 41 4 5 6.3 6.3 12 23 37 49 5 5 6.3 12 16 27 4 5 5 6.3 8.4 16 18 29 Case size φ D (mm) Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size are given in page 25. Please contact us for the soldering by reflow. Please refer to page 3 for the minimum order quantity. CAT.8100V