UZE1HR22MCL1GB

ALUMINUM  ELECTROLYTIC  CAPACITORS ZE 3.95mmL MAX. Chip Type, Bi-polarized series Chip type with 3.95mmL MAX, height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). ZP Smaller Products which are scheduled to be discontinued. Not recommended for new designs ZE Specifications Item Performance Characteristics Category Temperature Range –40 to +85°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 47µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 25 35 50 16 0.18 0.16 0.16 0.20 10 0.24 6.3 0.30 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) 6.3 4 8 Z– 40°C / Z+20°C 10 3 8 16 2 4 Shelf Life Resistance to soldering heat Marking Chip Type 0.5 MAX. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 U Z E 1 C 1 0 0 MC L 1 GB A±0.3 C±0.2 Taping code A±0.3 E B±0.2 A2 10C ZE φD±0.5 Series Capacitance 3.90 +0.05 –0.2 0.5 to 0.8 Voltage V 50 2 3 Type numbering system (Example : 16V 10µF) Plastic platform 0.3 MAX. Voltage (C : 16V) 35 2 3 The specifications listed at right shall be met when Capacitance change Within ±30% of the initial capacitance value the capacitors are restored to 20°C after the rated tan δ 300% or less than the initial specified value voltage is applied for 1000 hours at 85°C with the Less than or equal to the initial specified value Leakage current polarity inverted every 250 hours. After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within ±10% of the initial capacitance value is maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Leakage current Less than or equal to the initial specified value removed from the plate and restored to 20°C. Black print on the case top. Endurance Lot No. 25 2 4 φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 Configuration (mm) 6.3 2.4 6.6 6.6 2.2 Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) 6.3 10 16 25 35 50 Series name j A C E V H Type Code Dimensions 6.3 0J V Cap. (µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 5 6.3 6.3 10 1A 28 37 45 4 6.3 6.3 16 1C 17 33 41 4 5 6.3 6.3 25 1E 12 23 37 49 5 5 6.3 35 1V 12 16 27 4 5 5 6.3 8.4 16 18 29 50 1H 4 4 4 4 4 5 5 6.3 Case size φ D (mm) 1.0 2.0 2.8 4.0 8.4 13 17 20 Rated ripple Rated ripple current (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size soldering by reflow are given in page 18,19. Please refer to page 3 for the minimum order quantity. CAT.8100D