UZG1A100MCL

ALUMINUM ELECTROLYTIC CAPACITORS ZG 3.95mmL MAX. Chip Type, Wide Temperature Range series Chip type with 3.95mmLMAX height. Operating over wide temperature range of – 40 ~ +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). ZT Smaller ZG Specifications Item Category Temperature Range Rated Voltage Range Performance Characteristics – 40 ~ +105°C 6.3 ~ 50V ± 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Rated voltage (V) tan δ (MAX.) Rated voltage (V) Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) Z–40°C / Z+20°C 6.3 0.38 6.3 6 10 10 0.32 10 5 10 16 0.20 16 3 6 25 0.16 25 3 6 35 0.14 35 3 4 50 0.14 50 3 4 Within ±30% of initial value 300% or less of initial specified value Initial specified value or less Rated Capacitance Range 0.1 ~ 100µF Capacitance Tolerance Leakage Current tan δ 120Hz 20°C 120Hz Stability at Low Temperature Endurance After 1000 hours' application of rated voltage at 105°C, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Shelf Life After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. Black print on the case top. Capacitance change tan δ Leakage current Resistance to soldering heat Marking Within ±10% of initial value Initial specified value or less Initial specified value or less Chip Type Positive 0.5 MAX. Voltage (C : 16V) Lot No. Series Plastic platform 0.3 MAX. C ± 0.2 Type numbering system (Example : 16V 10µF) 1 (mm) 6.3 2.4 6.6 6.6 2.2 2 3 4 5 6 7 8 9 10 11 12 13 14 U ZG 1 C 1 0 0 MC L 1 GB A ± 0.2 A ± 0.2 φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 Taping code Configuration Capacitance tolerance (± 20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Type X2 10C ZG φD ± 0.5 B ± 0.2 Capacitance 3.90 +0.05 – 0.2 Voltage V Code 6.3 j 10 A 16 C 25 E 35 V 50 H 0.5 ~ 0.8 Dimensions V Cap. (µF) Code 6.3 0J 10 1A E Negative 16 1C 25 1E 35 1V 4 4 4 4 4 4 4 5 6.3 50 1H 0.9 2.2 2.8 3.3 5.4 9.6 12. 16. 26. 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 19 26 32 52 5 5 6.3 24 30 40 4 5 6.3 6.3 16 26 35 44 4 5 6.3 6.3 11 20 33 42 4 5 6.3 13 22 36 Case size φ D (mm) Rated ripple Rated Ripple (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size are given in page 25. Please contact us for the soldering by reflow. Please refer to page 3 for the minimum order quantity. CAT.8100V