UZT1E4R7MCL1GB

ALUMINUM  ELECTROLYTIC  CAPACITORS UZT 4.5mmL Chip Type, Wide Temperature Range UWT Chip type with 4.5mm height, operating over wide temperature range of – 40 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. Smaller UZT Smaller UZG Specifications Item Performance Characteristics Category Temperature Range –40 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) 6.3 0.38 Rated voltage (V) tan δ (max.) 10 0.32 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z(– 25°C) / Z(+20°C) Impedance ratio ZT / Z20 (max.) Z(– 40°C) / Z(+20°C) 6.3 6 10 10 5 10 Shelf Life Resistance to soldering heat Marking 25 3 6 35 3 4 50 3 4 Within ±25% of the initial capacitance value (16V or less) Within ±20% of the initial capacitance value (25V or more) tan δ 300% or less than initial specified value Leakage current Less than or equal to the initial specified value Capacitance change The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance 16 3 6 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within ±10% of the initial capacitance value is maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Black print on the case top. ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Chip Type Type numbering system (Example : 16V 10µF) 4.5 Voltage mark for 6.3V is 6V . +0.1 –0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 U Z T 1 C 1 0 0 MC L 1 GB 0.5 max. C±0.2 B±0.2 A2P 10 16V φD±0.5 Plastic platform Voltage 0.3 max. Lot No. Taping code A ± 0.3 E A ± 0.3 Capacitance 1 Positive 105˚C Marking 0.5 to 0.8 φD A B C E 4 1.8 4.3 4.3 1.0 Negative (mm) 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 Configuration Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) Series name Type Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50　　 Dimension table in next page. CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UZT Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） Rated Capacitance （µF） Case Size φD×L（mm） tan δ 22 4× 4.5 0.38 50 （1H） ） 3 Part Number 19 UZT0J220MCL1GB 33 5× 4.5 0.38 3 26 UZT0J330MCL1GB 5× 4.5 0.38 3 32 UZT0J470MCL1GB 100 6.3× 4.5 0.38 6.3 52 UZT0J101MCL1GB 22 5× 4.5 0.32 3 24 UZT1A220MCL1GB 33 5× 4.5 0.32 3.3 30 UZT1A330MCL1GB 47 6.3× 4.5 0.32 4.7 40 UZT1A470MCL1GB 10 4× 4.5 0.20 3 16 UZT1C100MCL1GB 22 5× 4.5 0.20 3.52 26 UZT1C220MCL1GB 33 6.3× 4.5 0.20 5.28 35 UZT1C330MCL1GB 47 6.3× 4.5 0.20 7.52 44 UZT1C470MCL1GB 4× 4.5 0.16 3 11 UZT1E4R7MCL1GB 10 5× 4.5 0.16 3 20 UZT1E100MCL1GB 22 6.3× 4.5 0.16 5.5 33 UZT1E220MCL1GB 33 6.3× 4.5 0.16 8.25 42 UZT1E330MCL1GB 4× 4.5 0.14 3 13 UZT1V4R7MCL1GB 10 5×4.5 0.14 3.5 22 UZT1V100MCL1GB 22 6.3× 4.5 0.14 7.7 36 UZT1V220MCL1GB 1 4× 4.5 0.14 3 5.4 UZT1H010MCL1GB 2.2 4× 4.5 0.14 3 9.6 UZT1H2R2MCL1GB 4.7 35 （1V） （ Rated Ripple （mArms） （105℃/120Hz） 47 4.7 25 （1E） Leakage Current （µA） at 20℃ after 2 minutes 3.3 4× 4.5 0.14 3 12 UZT1H3R3MCL1GB 4.7 5× 4.5 0.14 3 16 UZT1H4R7MCL1GB 6.3× 4.5 0.14 5 26 UZT1H100MCL1GB 10 For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. Please select UUX, UUJ series if high C/V products are required. CAT.8100L