NJL72H367A

NJL71H/71V/72H/73H/74H000A INFRARED REMOTE CONTROL RECEIVER s GENERAL DESCRIPTION The NJL70H/V000A series are small and high performance receiving devices for infrared remote control system. They can operate under low and wide supply voltage (2.4V to 5.4V). Also, their supply current is low comparing to the NJL60H/V000A and NJL80H/V000A. The features, low and wide supply voltage, low supply current are suitable for battery operated items. s FEATURES 1. Wide and low supply voltage 2.4V to 5.5V 2. Low supply current 0.6mA max. 3. Mold type and metal case type to meet the design of front panel. 4. Line-up for various center carrier frequencies. s APPLICATIONS 1. AV instruments such as Audio, TV, VCR, CD, MD etc. 2. Home application such as Air-conditioner, Fan etc. 3. Battery operated instruments such as Toy, Camera etc. s LINE-UP Mold/Metal case View Hight Mold type Top Side Metal Case type Top 11mm NJL73H360A NJL73H367A NJL73H380A NJL73H400A 15mm NJL74H360A NJL74H367A NJL74H380A NJL74H400A Carrier 5.4mm 6.3mm 8mm Frequency fo= 36 kHz NJL71H360A NJL71V360A NJL72H360A 36.7 kHz NJL71H367A NJL71V367A NJL72H367A 38 kHz NJL71H380A NJL71V380A NJL72H380A 40 kHz NJL71H400A NJL71V400A NJL72H400A Regarding other frequency or packages, please contact to New JRC individually. s BLOCK DIAGRAM Vcc Head Amp 2nd Amp 3rd Amp Comparator 22K Vout B.P.F. PD ABLC Detector GND s ABSOLUTE MAXIMUM RATINGS (Ta=25°C) PARAMETER Supply Voltage Operating Temperature Range Storage Temperature Range Soldering Temperature SYMBOL Vcc Topr Tstg Tsol RATINGS 6.3 -20 to +75 -40 to +85 260 (5sec. 4.0mm from mold body) UNIT V °C °C °C -1- NJL71H/71V/72H/73H/74H000A s RECOMMENDED OPERATING CONDITION Supply Voltage Range Vcc 2.4 V to 5.5V s ELECTRO-OPTICAL CHARACTERISTICS (Vcc=3.3V,Ta=25°C) PARAMETER Supply Current Transmission Distance Directivity Output Voltage Low Output Voltage High Low Level Pulse Width High Level Pulse Width Center Frequency SYMBOL Icc Lc θL θV VL VH TwL TwH fo TEST CONDITION No Signal Input Direction of Ray Axis *1 Angle of half Lc, Horizontal *2 Angle of half Lc, Vertical *2 No Load No Load See Test Circuit See Test Circuit See Line-up MIN — 13 — — — 2.8 350 400 36.0 TYP 0.43 18 45 30 0.2 — — — — MAX 0.6 — — — 0.5 — 800 850 40.0 UNIT mA m deg deg V V µs µs kHz Note *1:Test with each center carrier frequency under the test condition shown below. *2:Place major axis of elliptic lens in horizontal direction and minor vertical. s TEST METHOD Test condition in as follows: (1) Standard transmitter: Transmitting waveform is shown in Fig.1 Transmitting power should be adjusted so that output voltage Vout will be 400mVp-p.(Test circuit is shown in Fig.2) Regarding IR LED used for transmitter, λp=940nm, ∆λ=50nm. Regarding photo diode, Sensitivity S=26nA/Lx in case light source temperature2856°K, Ee=100Lx, VR=5V (2) Test system: Shown in Fig.3. IR TRANSMITTER OUTPUT WAVE FORM Carrier frequency is adjusted to center frequency of each product 600us 600us VH OUTPUT PULSE OF DEVICE TWL TWH VL Fig.1 TRANSMITTER WAVE FORM 20cm 10K 4.9 -5.1V + - 100K SENSING DISTANCE : L Vout Vcc OUT STANDARD TRANSMITTER Vout Fig.2 STD.TRANSMITTER TEST CIRCUIT GND Fig.3 TEST SYSTEM -2- NJL71H/71V/72H/73H/74H000A s TYPICAL CHARACTRISTICS Directivity 　(Ta=25℃) 100 90 Spectral Response (Ta=25°C) 100 90 Relative Transmission Distance (%) 700 800 900 1000 1100 Relative Responsibirity (%) 80 70 60 50 40 30 20 10 0 600 80 70 60 50 40 30 20 10 0 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 Wavelength (nm) Angle θ (deg) Horizontal Vertical Output Pulse Width vs. Distance (Input Pulse Width=600μs, Vcc=3.3V, Ta=25℃) Output Pulse Width TwL (μs) 850 750 650 550 450 350 0 2 4 6 8 10 12 14 16 18 Transmission Distance vs. Supply Voltage (Ta=25°C) Transmission Distance Lc (m) 20 18 16 14 12 10 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Transmission Distance Lc (m) Supply Voltage Vcc(V) Transmission Distance vs.Carrier Frequency (Vcc=3.3V,Ta=25°C) 100 Transmission Distance vs. Temperature (Vcc=3.3V) 20 18 16 14 12 10 8 -40 -20 0 20 40 60 80 100 Am bient temperature Ta(℃ ） Relative Distance (%) 80 70 60 50 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Carrier Frequency (kHz) fo=36kHz fo=40kHz Transmission Distance Lc (m) 90 -3- NJL71H/71V/72H/73H/74H000A s RECOMMENDED APPLICATION CIRCUIT 1 : OUT 2 : GND 3 : Vcc 47Ω 12 3 47uF Vcc RC Filter should be connected closely between Vcc pin and GND pin. s OUTLINE 5.4 6.2 2.2 3.2 6.2 5.4 2.2 3.2 2.6 7.3 4.7 7.3 0.4 1.6 2.5 1.6 4.7 2.6 0.5 2.54 2.54 1.0 0.5 16.5±0.5 2.2 4.0 2.2 1.0 0.4 1 : OUT 2 : GND 3 : Vcc 123 2.54 2.54 123 1 : OUT 2 : GND 3 : Vcc N JL71H000A UNIT:mm 5.4 6.2 2.2 3.2 NJL71V000A UNIT:mm 7.3 4.7 2.6 0.5 2.54 2.54 1.6 2.2 1.0 13.1 1 : OUT 2 : GND 3 : Vcc 123 NJL71H000AF3 UNIT:mm -4- 0.4 2.5 NJL71H/71V/72H/73H/74H000A 8.0 7.0 3.0 1.9 6.1 3.5 3.5 7.0 3.0 1.9 11.0 9.1 3.5 3.5 10.2 8.0 10.2 8.0 2.0 0.4 2.54 0.3 2.54 1 : OUT 2 : GND 3 : Vcc 2.5 (9.6) 2.54 2.54 0.3 1 : OUT 2 : GND 3 : Vcc 2.5 (12.6) 8.2 8.2 0.5 6.7 0.4 2.0 1.3 0.5 2.0 123 2.54 2.54 3 - φ 0.8 1.3 PCB Pattern 123 2.54 2.54 PCB Pattern N JL72H000A UNIT:mm NJL73H000A UNIT:mm 15.0 7.0 3.0 1.9 13.1 3.5 8.0 10.2 2.54 2.54 0.3 1 : OUT 2 : GND 3 : Vcc 2.5 (16.6) 8.2 2.0 0.5 2.54 2.54 6.7 0.4 3 - φ 0.8 2.0 3.5 PCB Pattern 1.3 123 NJL74H000A UNIT:mm 1. Tolerance is ±0.3mm unless otherwise noted. 2. Ground metal case on PCB. Metal case is not connected to GND pin inside.Tolerance is ±0.3mm unless otherwise noted. [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. 6.7 3 - φ 0.8 2.0 -5-