NJM2582

NJM2582 4CH VIDEO AMPLIFIER FOR SCART s GENERAL DESCRIPTION The NJM2582 is a 4ch video amplifier for SCART connecter. It can output DC that conforms to the SCART connector. The NJM2582 is suitable for the video application with the SCART connector. s FEATURES q Operating Voltage ±5V, +5V, +11V q 6input 4output q 2input 1output Video SW q Internal LPF q 6dB Amplifier q Internal 75Ω Driver Circuit q DC output for SCART (FUNCTION SW, BLANKING) q Power Save Circuit q Bipolar Technology q Package Outline SSOP32 sBLOCK DIAGRAM s PACKAGE OUTLINE NJM2582V VIN VYDCCONT SYIN V+1 1 Bias 2 5MHz LPF 6dB Amp 75Ω Driver 32 V/SYOUT NC SC/ROUT NC V+2 GOUT GND2 BOUT V-2 V+S1 (5V) BLANKING GNDS NC FunctionSW V+S2 (11V) WIDE 31 3 Bias 4 5MHz LPF 6dB Amp 75Ω Driver 30 29 SCDCCONT 5 SCIN GND1 RIN NC 6 Bias 7 28 27 5MHz 8 Bias 9 LPF 6dB Amp 75Ω Driver 26 25 24 6dB Amp 75Ω Driver GIN 10 Bias 5MHz LPF 23 V-1 11 BIN 12 Bias PS1(SC/Rmute) PS2(G,Bmute) PS3(V/Ymute) SW 22 21 MUTE 13 DISCEXT 14 EUROVY 15 RGBSEL 16 20 19 SW MATRIX 18 17 Ver.9 -1- NJM2586 sABSOLUTE MAXIMUM RATINGS (Ta=25°C) PARAMETER SYMBOL +Supply Voltage1 V /V + Supply Voltage2 V Power Dissipation PD Operating Temperature Range Topr Storage Temperature Range Tstg NJM2582 NJM2587 RATINGS ±6.5 +13 1250(Note1) -40 to +85 -40 to +150 UNIT V V mW °C °C (Note1) At on a board of EIA/JEDEC specification. (114.3 x 76.2 x 1.6mm Two layers, FR-4) s RECOMMENDED OPEARATING CONDITION (Ta=25°C) PARAMETER Operating Voltage1 Operating Voltage2 Operating Voltage3 SYMBOL Vopr1 Vopr2 Vopr3 TEST CONDITION V+1, V+2, V+S1 V-1, V-2 V+S2 + + + MIN. 4.5 -5.5 10.5 + TYP. 5.0 -5.0 11.0 MAX. 5.5 -4.5 11.5 UNIT V V V sELECTRICAL CHARACTERISTICS (Ta=25°C,V 1 to V 2=5V, V 1 to V 2=-5V, V S1=+5V,V S2=+11V, RL=150Ω) ▪ Input signal condition (SYIN, VIN, RIN, GIN, BIN) Video sync tip= 0V, Sine Signal Bottom= 0V (SCIN) Offset= 0.6V PARAMETER Operating Current1 SYMBOL ICC1 TEST CONDITION MIN. -45.0 -55.0 3.0 5.6 5.6 -0.2 -1.0 -1.0 TYP. 45.0 -35.0 45.0 -40.0 4.0 4.0 6.0 6.0 0 0 -25.0 0 -25.0 MAX. 60.0 60.0 5.5 6.4 6.4 +0.2 0.5 -14.0 0.5 -14.0 UNIT mA mA mA mA mA Vp-p dB dB dB dB dB dB dB (Note2) No Signal V+=5V, V-=-5V, VYDCCONT=L (Note2) No Signal Operating Current2 Iee2 V+=5V, V-=-5V, VYDCCONT=L (Note2) No Signal Operating Current3 ICC3 V+=5V, V-=-5V, VYDCCONT=H (Note2) No Signal Operating Current4 Iee4 V+=5V, V-=-5V, VYDCCONT=H Operating Current (Note3) No Signal Isave at Power Save V+=5V Maximum Output Voltage (SYIN, VIN, RIN, GIN, BIN) Vom Swing Vin=100kHz, Sine Signal, THD=1% (SYIN, VIN, RIN, GIN, BIN) Voltage Gain1 Gv1 Vin=1MHz, 1.0Vp-p, Sine Signal (SCIN) Voltage Gain2 Gv2 Vin=4.43MHz, 0.3Vp-p,Sine Signal Gain Difference (SYIN, VIN, RIN, GIN, BIN) ∆GvI Between channel Vin=1MHz, 1.0Vp-p,Sine Signal (SYIN, VIN, RIN, GIN, BIN) Gfy5M 5MHz/1MHz, 1.0Vp-p, Sine Signal Low Pass Filter Characteristic 1 (SYIN, VIN, RIN, GIN, BIN) Gfy27M 27MHz/1MHz, 1.0Vp-p, Sine Signal (SCIN) Gfc5M 5MHz/4.43MHz, 0.3Vp-p, Sine Signal Low Pass Filter Characteristic 2 (SCIN) Gfc27M 27MHz/4.43MHz, 0.3Vp-p, Sine Signal (Note2) MUTE, DISCEXT, EUROVY = H , WIDE, RGBSEL = L (Note3) MUTE = L -2- NJM2582 NJM2587 NJM2586 sELECTRICAL CHARACTERISTICS (Ta=25°C,V 1 to V 2=5V, V 1 to V 2=-5V, V S1=+5V,V S2=+11V, RL=150Ω) PARAMETER Group Delay Cross talk Differential Gain Differential Phase S/N Ratio SYMBOL GD CT DG DP SN TEST CONDITION 5MHz/1MHz (SYIN, VIN, RIN, GIN, BIN) 4.43MHz, 1.0Vp-p, Sine Signal (SCIN) 4.43MHz, 0.3Vp-p, Sine Signal (SYIN, VIN, RIN, GIN, BIN) Vin=1.0Vp-p, 10step Video Signal (SYIN, VIN, RIN, GIN, BIN) Vin=1.0Vp-p, 10step Video Signal (SYIN, VIN, RIN, GIN, BIN) Vin=1.0Vp-p,100% White video signal, RL=75Ω,100KHz to 6MHz + + + + + + + MIN. + TYP. 8.0 -70 0.3 0.3 80 MAX. - UNIT nSec dB % deg dB sELECTRICAL CHARACTERISTICS (Ta=25°C,V 1 to V 2=5V, V 1 to V 2=-5V, V S1=+5V,V S2=+11V, RL=150Ω) PARAMETER Switch Change Voltage High Level Switch Change Voltage Low Level V/SY Output Voltage H V/SY Output Voltage L SC Output Voltage H SC Output Voltage L RGB Output Voltage Function Switch Output Voltage H Function Switch Output Voltage M Function Switch Output Voltage L Blanking Output Voltage H Blanking Output Voltage L Switch inflow current High Level Switch inflow current Low Level SYMBOL VthH VthL VSYH VSYL VSCH VSCL VRGB VFH VFM VFL VBH VBL ISWH ISWL TEST CONDITION MUTE, DISCEXT, EUROVY, RGBSEL WIDE, VYDCCONT, SCDCCONT MUTE, DISCEXT, EUROVY, RGBSEL WIDE, VYDCCONT, SCDCCONT TP1, VYDCCONT=H TP1, VYDCCONT=L TP2, SCDCCONT=H TP2, SCDCCONT=L TP2, TP3, TP4 TP6 TP6 TP6 TP5 TP5 MIN. 2.5 0 -0.4 -0.1 -0.7 -0.1 0.0 10.0 5.3 1.5 TYP. -0.3 0.0 -0.6 0.0 MAX. V + UNIT V V V V V V V V V V V V uA uA 1.0 -0.2 0.1 -0.5 0.1 2.0 11.0 6.3 1.5 2.5 0.3 120 8 -3- NJM2586 sLOGICAL TABLE NJM2582 NJM2587 MUTE H H H H H H H H L L L L L L L L INPUT 4chAMP OUT MONITOR DISCEXT EUROVY RGBSEL V V H H H H H L V, RGB RGB SY SY H L H H L L * * V L H H L H L V, RGB TV Mode SY L L H L L L * H H H H H L OFF H L H 4ch OFF H L L L H H TV Mode L H L L L H L L L 4ch OFF TV Mode BLANKING L H L L L H L L L H L L L L L L No use * No use INPUT DISCEXT WIDE H H H L L H L L OUTPUT Function SW M H L L Mode DVD TV MUTE DISCEXT EUROVY RGBSEL WIDE VYDCCONT SCDCCONT H L H L H L H L H L H L H L 4chAMP ON 4chAMP OFF DVD MODE TV MODE V OUT SY/SC OUT RGB OFF RGB ON 16: 9 4: 3 -0.3V 0V -0.6V 0V -4- NJM2582 NJM2587 NJM2586 sEQUIVALENT CIRCUIT PIN No. PIN NAME 1 3 6 8 10 12 VIN SYIN SCIN RIN GIN BIN 20k GND1 V-1 270 EQUIVALENT CIRCUIT V+1 DC VOLTAGE NOTE 0V 2 5 13 14 15 16 17 VYDCCONT SCDCCONT MUTE DISCEXT EUROVY RGBSEL WIDE V-1 GND 48k 58k 0V V+2 19 FunctionSW 4.1k 0V 6V 10.5V V-2 V+S1 16k 22 Blanking 0V 2.1V 80k GND V-2 -5- NJM2586 sEQUIVALENT CIRCUIT PIN No. PIN NAME EQUIVALENT CIRCUIT V+2 NJM2582 NJM2587 DC VOLTAGE NOTE 25 27 30 32 BOUT GOUT SCROUT VSYOUT 4.1k 0.1V 0.1V 0V, -1.2V, 0.1V 0V, -0.6V V-2 -6- NJM2582 NJM2587 NJM2586 sTEST CIRCUIT 1 VYDCCONT, SCDCCONT=H VEE -5V + 47uF 1 75Ω 2 VIN VYDCCONT SYIN V+1 SCDCCONT SCIN GND1 RIN NC GIN V-1 BIN MUTE DISCEXT EUROVY RGBSEL TP1 V/SYOUT 32 75Ω 75Ω + VCC 5V 47uF NC 31 TP2 3 75Ω 4 0.1uF 5 SC/ROUT 30 75Ω 75Ω NC 29 V+2 28 GOUT 27 75Ω 75Ω 0.1uF TP3 6 75Ω 7 GND2 26 TP4 8 75Ω 9 BOUT 25 75Ω 75Ω V-2 24 V+S1 (5V) 23 BLANKING 22 0.1uF 10 75Ω 0.1uF 11 0.1uF 5V 75Ω 10k Ω TP5 75Ω 12 75Ω 13 GNDS 21 NC 20 390Ω 14 TP6 10k Ω FunctionSW 19 V+S2 (11V) 18 WIDE 17 VCC 11V 0.1uF + 15 47uF 16 -7- NJM2586 sTEST CIRCUIT 2 VYDCCONT, SCDCCONT=L NJM2582 NJM2587 VEE -5V + 47uF 10uF + 1 2 VIN VYDCCONT SYIN V+1 SCDCCONT SCIN GND1 RIN NC GIN V-1 BIN MUTE DISCEXT EUROVY RGBSEL V/SYOUT 32 NC 31 SC/ROUT 30 NC 29 V+2 28 GOUT 27 GND2 26 BOUT 25 V-2 24 V+S1 (5V) 23 BLANKING 22 + TP1 75Ω 75Ω + VCC 5V 47uF 75Ω 470uF 10uF + 3 + TP2 75Ω 75Ω 75Ω 4 0.1uF 5 10uF + 470uF 0.1uF + TP3 75Ω 75Ω 6 75Ω 7 10uF + 470uF 8 + TP4 75Ω 75Ω 75Ω 9 10uF + 470uF 0.1uF 10 75Ω 0.1uF 10uF + 0.1uF 5V 75Ω 10k Ω TP5 75Ω 11 12 GNDS 21 NC 20 75Ω 13 390Ω 14 TP6 10k Ω FunctionSW 19 V+S2 (11V) 18 WIDE 17 VCC 11V 0.1uF + 15 47uF 16 -8- NJM2582 NJM2587 NJM2586 sAPPLICATION CIRCUIT VEE -5V + 47uF CVBS SY 75Ω 1 2 VIN VYDCCONT SYIN V+1 SCDCCONT SCIN GND1 RIN NC GIN V-1 BIN MUTE DISCEX T EUROVY RGBSEL V /SYOUT 32 75Ω + VCC 5V 47uF Video DAC SC R G B 75Ω NC 31 SC/ROUT 30 75Ω TV SCART 3 19 15 11 7 8 16 4 0.1uF 5 NC 29 V+2 28 GOUT 27 75Ω 0.1uF 6 75Ω 7 GND2 26 BOUT 25 75Ω 8 75Ω 9 V-2 24 V+S1 (5V) 23 BLANKING 22 GNDS 21 NC 20 0.1uF 10 75Ω 0.1uF 11 0.1uF 5V 75Ω 10kΩ 12 75Ω VYDCCONT SCDCCONT MUTE 13 390Ω 14 Micon DISCEXT EUROVY RGBSEL WIDE FunctionSW 19 V+S2 (11V) 18 WIDE 17 VCC 11V 0.1uF + 15 47uF 16 [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. -9-