AT636F05

Toggles Series YB2 Rockers General Specifications Electrical Capacity (Resistive Load) Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Other Ratings D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: Materials & Finishes Bezel: Housing: Base: Movable Contactor: Movable Contacts: Stationary Contacts: Switch Terminals: Lamp Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Sealing: 50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit 100,000 operations minimum Single pole: 1.5N Double pole: 3.0N Nonshorting (break-before-make) Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm) Black: Glass fiber reinforced polyamide (UL94V-0); Chrome plated: Chrome plating over ABS resin (UL94V-2) Glass fiber reinforced polyamide (UL94V-0) Glass fiber reinforced polyamide (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy or copper with gold plating Silver alloy or copper with gold plating Phosphor bronze with tin plating Phosphor bronze with tin plating –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) IP65 of IEC60529 standard Installation Mounting Torque: 0.785Nm (6.95 lb•in) maximum Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 housing, base & black bezel UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/CUL” before first dash in part number to order cULus marking on switch. All solder lug models recognized at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum. Supplement Accessories Panel Seal Pushbuttons D118 www.nkkswitches.com Toggles Series YB2 Rockers Distinctive Characteristics Pushbuttons 24mm square and 25mm diameter pushbuttons with the shortest above-panel dimension (1.8mm) in the industry for splashproof design. Meets IP65 of IEC60529 standards (similar to NEMA 4 and 13), providing dust tight and splashproof panel seal protection. Tamper resistant 18mm square and 19mm diameter actuators. D Short body of .965” (24.5mm) conserves behind-panel space. Keylocks Distinctive long stroke and light touch actuation for clear indication of circuit status. Programmable Illuminated PB Panel Seal Pushbuttons Rotaries Choice of cap colors includes clear, brushed chrome, red, green, or yellow, for enhanced panel appearance. Metallic silver cap option has bright ring illumination (round only). Unbrushed chrome has the look of stainless steel when nonilluminated, and LED color or legends when illuminated. Slides Brilliant illumination with multiple LED colors. Bezel color options in black or brushed chrome. Tactiles Brushed chrome option is lighter weight than actual metal switches due to metal plating on resin. Tilt Available in momentary and alternate action with latchdown. Actual Size (Round) Indicators Combination solder lug and .110” quick connect terminals. Terminals are epoxy sealed to lock out flux, dust, solvents, and other contaminants, as well as to secure terminals and improve contact stability. Touch Crisp actuation and clear circuit status provided by snap-action contact mechanism. Arc barrier protects against crossover. Supplement Accessories Custom legends on actuator or inserts. www.nkkswitches.com D119 Toggles Series YB2 TYPICAL SWITCH Rockers Pushbuttons Programmable Illuminated PB Keylocks 1 YB2 5 Poles D 5 SPDT 2 DPDT ON W C W K Round S Square With Panel Seal Contact Materials & Ratings K Black P Brushed Chrome W Silver Rated 3A @ 125V AC G Gold Rated 0.4VA maximum @ 28V AC/DC maximum ON IMPORTANT: Tilt Tactiles Switches are supplied without cULus marking unless specified. cULus recognized only when ordered with marking on the switch. Specific models, ratings, and ordering instructions are noted on General Specifications page. Touch DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators YB215CWCKW01-6B-JB LED Cap with Clear Lens & White Diffuser White, Super Bright LED Black Bezel With Panel Seal Accessories Round Black Housing SPDT ON-(ON) Circuit Supplement Silver Contacts with 3 Amp Rating Solder Lug/.110” (2.8mm) Quick Connect Terminals D120 www.nkkswitches.com 01 Solder Lug/.110” (2.8mm) Quick Connect 01 Bezel Alternate Action with Latchdown Slides W Terminals C Panel Seal (ON) C Shape Normally Open and Normally Closed ( ) = Momentary ON C Contact Point 1 Circuits 6 Rotaries Panel Seal Pushbuttons Series YB2 Toggles Panel Seal Pushbuttons Cap Types & Colors Bright LED Lens/Diffuser Colors LED Colors No Code 5C Red 5D Amber 5F Resistor Green No Resistor (not for Green) 05 5-volt 12 12-volt 24 24-volt JB Clear/White JS Metallic Silver Cap/Clear Ring (Round only) CB Red/White EB Yellow/White FB Green/White HB Unbrushed Chrome/White LED and cap need to be the same color. Yellow cap pairs with amber LED to achieve amber illumination. Codes JB and JS (Round only) may be combined with all LED colors. Pushbuttons LEDS D Round or Square Cap with Legend 001 Programmable Illuminated PB JB Keylocks 6 B Rockers ORDERING EXAMPLE 002 START 003 STANDBY 004 STOP White 6F Green 6G Blue JB Clear/White JS Metallic Silver Cap/Clear Ring (Round only) HB Unbrushed Chrome/White 005 Rotaries 6B Lens/Diffuser Cap Colors Contact factory for custom options. Round or Square Cap with Legend 001 JB Clear/White 003 STANDBY CB Red/White 004 STOP EB Yellow/White 005 FB Green/White Contact factory for custom options. HB Unbrushed Chrome/White Brushed Chrome Touch P Tilt No Lamp 002 START Round Cap for Super Bright LED Square Cap for Bright or Super Bright LED AT3017HB-001 AT3018HB-001 AT3025HB-001 AT3017HB-002 AT3018HB-002 AT3025HB-002 AT3017HB-003 AT3018HB-003 AT3025HB-003 AT3017HB-004 AT3018HB-004 AT3025HB-004 AT3017HB-005 AT3018HB-005 AT3025HB-005 Accessories Round Cap for Bright LED Indicators Part Numbers for Unbrushed Chrome Caps with Legends Supplement N Cap Color Tactiles Nonilluminated Slides Super Bright LED Refer to Ordering Table for legend that corresponds with last 3 digits of part number. www.nkkswitches.com D121 Series YB2 Toggles Panel Seal Pushbuttons POLES & CIRCUITS D Connected Terminals Throw & Switch/Lamp Schematics Notes: Switch is marked with NC, NO, COM, L+, L–. Lamp circuit is isolated and requires an external power source. Normal Down Normal Down YB215 YB216 ON ON (ON) ON 1-3 1-2 SPDT YB225 YB226 ON ON (ON) ON 1-3 4-6 1-2 4-5 DPDT Pole Model SP DP 1 (COM) 3 NC 3 NC C W Normally Open and Normally Closed Rotaries Slides L (+) (-) L 4 6 NC 5 NO Panel Seal (Round and Square) Two o-rings provide panel seal protection meeting IP65 of IEC60529 standards. BEZEL K Square Tactiles S (COM) 2 NO SHAPE Round (-) L PANEL SEAL Contact points are both Normally Open and Normally Closed. C L (+) 2 NO 1 CONTACT POINT Keylocks Programmable Illuminated PB Pushbuttons Rockers Plunger Position ( ) = Momentary P Black Brushed Chrome Tilt For Round or Square W G Silver Contacts 01 D122 Gold Contacts Power Level: 3A @ 125/250V AC Logic Level: 0.4VA max. @ 28V AC/DC max. Switch base is black Switch base is ivory TERMINALS Supplement Accessories Indicators Touch CONTACT MATERIALS & RATINGS Solder Lug/ .110” (2.8mm) Quick Connect Epoxy Seal (7.3) .288 (2.0) (2.8) .079 .110 (1.2) .047 Thk = (0.5) .020 www.nkkswitches.com Toggles Series YB2 BRIGHT & SUPER BRIGHT LEDS Rockers The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. Base of AT634 and AT636 is Black for 5V, Light Blue for 12V and Gray for 24V. Electrical Specifications for Bright LED without Resistor 5C Red 5D No Code Amber LED Colors T-1 Bi-pin (+) (-) No Resistor Unit Red Amber Maximum Forward Current IFM 40 40 mA Typical Forward Current IF 26 26 mA Forward Voltage VF 1.9 2.0 V Maximum Reverse Voltage VRM 4 4 V Current Reduction Rate Above 25°C ∆IF Ambient Temperature Range Pushbuttons Colors Available: D 0.50 mA/°C –25 ~ +50 °C T-11⁄4 Bi-pin 5C Red 5D Amber 05 12 24 Unit Maximum Forward Current IFM — — — mA Typical Forward Current IF 25 20 10 mA Forward Voltage VF 5 12 24 V Maximum Reverse Voltage VRM 4 8 16 V Current Reduction Rate Above 25°C ∆IF — — ­­— mA/°C Ambient Temperature Range AT634 5-volt, (+) 2-element with Resistor AT634 12-volt, 4-element with Resistor (-) –25 ~ +50 (+) °C AT634 (+) 24-volt, 4-element with Resistor (-) Rotaries Colors Available: Slides Bright AT634 Keylocks Electrical Specifications for Bright Red & Amber LED with Resistor (-) Colors Available: (-) (+) 5V (-) (+) 12V & 24V 5F Green 05 12 24 Unit Maximum Forward Current IFM — — — mA Typical Forward Current IF 11 9.5 8.7 mA Forward Voltage VF 5 12 24 V Maximum Reverse Voltage VRM 5 5 5 V Current Reduction Rate Above 25°C ∆IF — — ­­— mA/°C ELECTROSTATIC SENSITIVE DEVICES Ambient Temperature Range –25 ~ +50 Tilt T-11⁄4 Bi-pin ATTENTION Tactiles Electrical Specifications for Bright Green LED with Resistor Bright AT636 Programmable Illuminated PB Bright AT628 °C Touch Panel Seal Pushbuttons T-1 Bi-pin 6B ATTENTION ELECTROSTATIC SENSITIVE DEVICES (+) (-) Colors: White 6F Green 6G Blue Unit IFM 30 30 30 mA Typical Forward Current IF 20 20 20 mA Forward Voltage VF 3.3 3.3 3.3 V Maximum Reverse Voltage VRM 7 7 7 V Current Reduction Rate Above 25°C ∆IF 0.40 0.40 0.40 mA/°C Ambient Temperature Range –25 ~ +50 www.nkkswitches.com Accessories Maximum Forward Current °C D123 Supplement Super Bright AT625G Blue AT631B White AT632F Green Indicators Electrical Specifications for Super Bright LED Toggles Series YB2 BALLAST RESISTOR CALCULATION FOR LEDS R Rockers If the source voltage is greater than the rated voltage of a lamp or LED, a ballast resistor must be connected in series with the lamp. This circuit diagram and formula will assist in calculating the value of the required ballast resistor. Pushbuttons Programmable Illuminated PB Keylocks Rotaries Panel Seal Pushbuttons + IF R = Anode Where: R = E = VF = IF = VF E Cathode – E – VF IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) CAPS & CAP COLORS D AT3017 Cap for Bright LED or Nonilluminataed AT3018 Cap for Super Bright LED AT3019 Cap for Nonilluminated AT3020 Cap with Illumination Ring for Bright or Super Bright LED Lens/Diffuser Colors Available: Lens/Diffuser Colors Available: Cap Color Available: Cap Color Available: JB Clear/White JB Clear/White P CB Red/White EB HB Unbrushed Chrome/ White * Yellow/White FB Green/White HB Unbrushed Chrome/ White Brushed Chrome JS (19.0) Dia .748 (19.0) Dia .748 Metallic Silver with Clear Ring (19.0) Dia .748 (13.1) .516 (13.1) .516 (4.9) .193 (4.9) .193 (13.1) .516 (4.9) .193 Slides (19.0) Dia .748 (13.1) .516 Supplement Accessories Indicators Touch Tilt Tactiles (4.9) .193 Material for Lens & Diffuser: Polycarbonate H B Lens: ABS Resin & Unbrushed Chrome Plating Material for Lens: ABS Resin & Brushed Chrome Plating Materials Lens: Polycarbonate Insert: Polyester *Yellow cap pairs with amber LED to achieve amber illumination. AT3025 Cap for Illuminated or Nonilluminated AT3027 Cap for Nonilluminated Lens/Diffuser Colors Available: Cap Color Available: JB Clear/White For Bright & Super Bright LEDs CB Red/White For Bright LED only EB * Yellow/White For Bright LED only FB Green/White For Bright LED only HB Unbrushed Chrome/White For Bright & Super Bright LEDs P (18.0) Sq .709 (18.0) Sq .709 (13.1) .516 (4.9) .193 Material for Lens & Diffuser: Polycarbonate *Yellow cap pairs with amber LED to achieve amber illumination. D124 Brushed Chrome www.nkkswitches.com (13.1) .516 (4.9) .193 Material for Lens: ABS Resin & Brushed Chrome Plating Series YB2 Toggles Panel Seal Pushbuttons Standard Legends for Unbrushed Chrome Caps Round or Square Cap Bright or Super Bright LED Round or Square Cap Bright or Super Bright LED Round or Square Cap Bright or Super Bright LED D Round or Square Cap Bright or Super Bright LED Keylocks 005 Round or Square Cap Bright or Super Bright LED Rotaries 004 Rockers 003 Pushbuttons 002 Programmable Illuminated PB 001 Images appear the color of the LED when lit. Contact factory for other legends options. Slides Legend illustrations are approximate representations of the actual images on the caps. Tilt Tactiles Unbrushed Chrome/White Cap with Lens/Diffuser With Illumination Touch Without Illumination Supplement Accessories It is recommended that the legend be clear and without ink in order to achieve the maximum visibility when the cap is illuminated. Indicators Depending on the design and the color of ink used, the legend may be visible when it is not illuminated. www.nkkswitches.com D125 Series YB2 Toggles Panel Seal Pushbuttons TYPICAL SWITCH DIMENSIONS Rockers Single Pole (1.2) x (2.0) Typ .047 x .079 M16 P1 (3.7) .146 (3.7) .146 (9.7) .382 NC L 2 1 (19.0) Dia .748 (25.0) Dia .984 D (1.8) .071 (7.3) .288 (33.6) 1.323 (3.0) .118 (7.3) .288 COM (9.7) .382 5 -+ 1 COM 6 L 2 - + (2.8) Typ .110 NC 3 NO NO 3 NO Pushbuttons (0.5) Typ .020 NO 4 (6.0) .236 (11.1) .437 (5.55) .219 YB215CWCKW01-6B-JB Single Pole Keylocks Programmable Illuminated PB Double Pole M16 P1 (1.2) x (2.0) Typ .047 x .079 Double Pole (3.7) .146 (3.7) .146 (0.5) Typ .020 NC NC (9.7) .382 Rotaries (9.7) .382 Slides (18.0) Sq .709 (24.0) Sq .945 (1.8) .071 (7.3) .288 (33.6) 1.323 COM COM (2.8) Typ .110 (7.3) .288 (5.55) .219 (3.0) .118 (6.0) .236 (11.1) .437 Tactiles YB216CWSPW01-N-P PANEL THICKNESS & CUTOUT 0.3 Dia Typ (22.0) +– 0.0 .866 Tilt (25.4) Min 1.00 Touch Recommended Panel Thickness .020” ~ .197” (0.5mm ~ 5.0mm) (25.4) Min 1.00 Side-by-side Mounting + 0.1 (10.5) – 0.0 Typ .413 Indicators (1.7) +– 0.0 0.1 Typ .067 Accessories (24.5) Min .965 Recommended Panel Thickness .020” ~ .197” (0.5mm ~ 5.0mm) Supplement (24.5) Min .965 0.3 (21.0) +– 0.0 Sq Typ .827 D126 www.nkkswitches.com Side-by-side Mounting Series YB2 Toggles Panel Seal Pushbuttons OPTIONAL ACCESSORIES (3.0) Typ .118 (17.1) .673 (3.0) .118 (5.55) .219 (4.0) .157 NC NO L (17.0) .669 (4.85) Typ .191 L – + COM COM (3.7) Typ .146 (3.0) Typ .118 (5.55) Typ .219 (4.85) Typ .191 NO CL (3.7) Typ .146 (3.7) .146 (4.85) Typ .191 (1.0) Dia Typ .039 (1.85) Typ .073 (3.0) Typ .118 (4.0) .157 NC NO – + (3.7) .146 Pushbuttons (17.1) .673 AT719 Double Pole Straight PC Terminals (17.0) .669 NO D (3.7) .146 (5.55) Typ .219 AT718 Single Pole Straight PC Terminals NO (1.0) Dia Typ .039 (1.85) Typ .073 (3.0) Typ .118 (5.55) .219 CL (5.55) Typ .219 Note: Order adaptors separately Tilt Material: Glass fiber reinforced polyamide Programmable Illuminated PB – + COM (5.55) .219 (4.85) Typ .191 L – + (3.7) .146 (5.0) .197 NC NO COM (3.0) .118 Indicators Touch Round & Square Switch Dimensions Shown with Adaptor AT716 (37.8) 1.488 A A Accessories (37.8) 1.488 Dimension A: Solder Lug .197” (5.0mm); Straight PC .157” (4.0mm) Panel thickness for YB2 Round: Panel thickness for YB2 Square: .020” ~ .161” (0.5mm ~ 4.1mm) .020” ~ .126” (0.5mm ~ 3.2mm) www.nkkswitches.com Supplement (4.85) Typ .191 Tactiles NO L Keylocks (5.0) .197 NC NO (17.0) .669 Rotaries (17.0) .669 (4.85) Typ .191 (17.1) .673 AT717 Double Pole Solder Lug/ Quick Connect Terminals Slides (17.1) .673 AT716 Single Pole Solder Lug/ Quick Connect Terminals Rockers Adaptors D127 Series YB2 Toggles Panel Seal Pushbuttons ASSEMBLY INSTRUCTIONS FOR ROUND Keylocks Programmable Illuminated PB Pushbuttons Rockers 1. Remove knurled mounting nut. 5. Install the red o-ring which was removed in step 2 at the inside bottom of the bezel. Knurled Mounting Nut D Keyway Housing 3. Install LED. Red O-ring Rotaries LEDs AT634 & AT636 Slides Tactiles LED AT628 D-Flat Bezel ATTENTION ELECTROSTATIC SENSITIVE DEVICES Align D-flat on LED with Part Number on switch for appropriate polarity and insert LED into base. Align D-flat on LED with Part Number on switch for appropriate polarity and insert LED into base. (–) ATTENTION LEDs AT625G, AT631B, AT632F ELECTROSTATIC SENSITIVE DEVICES Back of Bezel 7. Before installing into panel, make sure that the orange o-ring is present at the back of the bezel. Align keyway on bezel with tab in panel and push switch all the way into the panel. Bezel Keyway Panel Tab 8. Attach mounting nut behind panel and tighten. Make sure that bezel and actuator fit properly and that there is no space between bezel and panel. Do not overtighten. The larger metal part within the LED represents the cathode (–). Align LED for appropriate polarity and insert LED into base. Mounting torque: 0.785Nm (6.95 lb•in) maximum. Optional socket wrench AT106 available. Touch Tilt (+) Tab Cathode Socket (–) Anode Socket (+) (–) Orange O-ring Red O-ring Bezel Part Number This Side D-Flat Bezel 6. Align tab inside of the bezel with keyway on housing and bring bezel back into its original position. 2. Remove bezel and red o-ring from housing. There are two o-rings in this assembly: one is red, one is orange. (+) Red O-ring Actuator Cathode (–) Supplement Accessories Indicators (+) (–) Bezel Anode (+) Panel Actuator 4. Align tabs (B) on both sides of actuator with the projections (A) inside of the housing and push actuator firmly down to snap in. B Knurled Mounting Nut A Housing AT106 Socket Wrench D128 www.nkkswitches.com Series YB2 Toggles Panel Seal Pushbuttons 5. Install the blue o-ring which was removed in step 2 at the inside bottom of the bezel. Blue O-ring Pushbuttons Bezel 6. Align tab inside of the bezel with keyway on housing and bring bezel back into its original position. Spacer Knurled Mounting Nut D Housing 2. Remove bezel and blue o-ring from housing. Keyway Blue O-ring Tab Keylocks Blue O-ring Bezel Bezel Part Number This Side LEDs AT634 & AT636 (–) LED AT628 D-Flat (+) Align D-flat on LED with Part Number on switch for appropriate polarity and insert LED into base. Align D-flat on LED with Part Number on switch for appropriate polarity and insert LED into base. (–) ATTENTION LEDs AT625G, AT631B, AT632F Rotaries Bezel Panel 8. Attach mounting nut behind panel and tighten. Make sure that bezel and actuator fit properly and that there is no space between bezel and panel. Do not overtighten. Mounting torque: 0.785Nm (6.95 lb•in) maximum. Optional socket wrench AT106 available. ELECTROSTATIC SENSITIVE DEVICES The larger metal part within the LED represents the cathode (–). Align LED for appropriate polarity and insert LED into base. Actuator Touch (+) ATTENTION ELECTROSTATIC SENSITIVE DEVICES Back of Bezel Slides Anode Socket (+) 7. Before installing into panel, make sure that the square gasket is present at the back of the bezel. Align keyway on bezel with tab in panel and push switch all the way into the panel. Tactiles Cathode Socket (–) Tilt 3. Install LED. D-Flat Bezel Anode (+) Spacer Accessories 4. Align tabs (B) on both sides of actuator with the projections (A) inside of the housing and push actuator firmly down to snap in. Cathode (–) Actuator Knurled Mounting Nut B A Supplement (–) Indicators Panel (+) Programmable Illuminated PB 1. Remove knurled mounting nut. Rockers ASSEMBLY INSTRUCTIONS FOR SQUARE Housing AT106 Socket Wrench www.nkkswitches.com D129 Series YB2 Toggles Panel Seal Pushbuttons LEGENDS Rockers NKK Switches can provide custom legends for caps. Contact factory for more information. Recommended Methods: Laser Etch on clear cap, Screen Print or Pad Print on cap. Epoxy based ink is recommended. D For Caps AT3017, AT3018, and AT3019 Keylocks Programmable Illuminated PB Pushbuttons Suggested Printable Area for YB2 Caps For Cap AT3020 (with clear ring for illumination) (0.76) Typ .030 (15.88) Dia .625 (19.0) Dia .748 Rotaries (17.48) Dia .688 (19.0) Dia .748 For Caps AT3025 and AT3027 (16.48) Sq .649 (18.0) Sq .709 (1.56) Typ .062 (0.76) Typ .030 Shaded areas are printable areas. Slides Suggested Printable Area for Film Inserts +0.1 (0.6) R Typ .024 Tactiles (1.2) –0.1 Typ .047 (14.78) .582 (0.5) R .020 Recommended Method: Screen Print; Epoxy based ink is recommended +0.1 (16.3) –0.0 .642 Tilt Film Material and Thickness: (15.88) .625 Touch (17.4) .685 (0.76) Typ .030 +0.08 –0.1 (14.88) Sq .586 (16.4) .646 +0.0 –0.1 (0.76) Typ .030 Clear Polyester, 4 mil max. Sq Indicators Shaded areas are printable areas. Accessories HANDLING & PRECAUTIONS ATTENTION LEDs are electrostatic sensitive devices. When installing and handling LEDs, use an electrostatic protected work station to prevent LED damage. Supplement ELECTROSTATIC SENSITIVE DEVICES D130 www.nkkswitches.com