AT716

Toggles Series LP01 Short Body Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) Contact Resistance: Insulation Resistance: Dielectric Strength: 50 milliohms maximum (DC2 ~ 4V 100mA) 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum Mechanical Life: 500,000 operations minimum Electrical Life: 50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC 100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC Nominal Operating Force: 1.5 ± 0.7N for Single Pole; 3.0 ± 1.2N for Double Pole Contact Timing: Nonshorting (break-before-make) Travel: Total Travel .118” (3.0mm) D Materials & Finishes Actuator: Housing: Polycarbonate Bushing mount: Glass fiber reinforced polyamide (UL94V-0); Snap in mount: Polybutylene terephthalate (PBT) (UL94V-0) Base: Glass fiber reinforced polyamide (UL94V-0) Movable Contact: Phosphor bronze & silver with silver plating Stationary Contacts: Common terminal: Phosphor bronze with silver plating; Contact terminals: Phosphor bronze with tin plating Lamp Terminals: Phosphor bronze with tin plating Slides Environmental Data Tactiles Operating Temperature Range: Humidity: Vibration: Tilt Shock: Installation Touch Mounting Torque: Soldering Time & Temperature: Cleaning: Standards & Certifications Flammability Standards: UL: Accessories Indicators 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC Other Ratings Rotaries Keylocks Programmable Illuminated PB Pushbuttons Power Level (silver): –10°C through +50°C (+14°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 0.8Nm (7.08 lb • in) maximum Manual Soldering: See Profile A in Supplement section. Hand clean locally with alcohol based solution UL94V-0 housing & base File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” to end of part number to order UL recognized switch. All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC. Supplement Note: The spot illuminated switches do not have UL approval and cannot be ordered with the markings. D68 www.nkkswitches.com 7/19/17 Toggles Series LP01 Rockers Distinctive Characteristics Pushbuttons Environmentally friendly components and packaging materials meet RoHS Directive restricting use of hazardous materials. Suited for lead-free soldering because of heat resistant resin materials. Smooth, slightly concave surface of cap designed to fit fingertip. Unique design and construction of cap prevents its removal and limits tampering. D Keylocks Bright LED illumination in choice of red, green or amber through translucent white cap. Spot illumination in red, green or amber enhanced by black cap. Programmable Illuminated PB Short Body Pushbuttons Rotaries Short body of .551” (14.0mm) conserves behindpanel space. Slides Installation options include 16.0mm bushing mount or 17.3mm snap-in mount. Tilt Tactiles Combination solder lug and .110” quick connect terminals are epoxy sealed to prevent entry of flux, dust, or other contaminants. Touch Crisp actuation and clear circuit status provided by snap-action contact mechanism. Arc barrier between movable contacts protects against crossover. Supplement Accessories Indicators Actual Size www.nkkswitches.com D69 Series LP01 Toggles Short Body Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE 1 5 Poles C C 1 SPDT C Bushing 2 DPDT M Snap-in Housing (ON) K LEDs Black ( ) = Momentary 5C Red 5D Amber 5F Green IMPORTANT: Rotaries Cap Color Nonilluminated A Black with Spot Illumination B White Nonilluminated Cap Colors No Nonilluminated Code Switches are supplied without UL & cULus markings unless specified. UL & cULus recognized only when ordered with marking on switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Spot illuminated switches do not have UL approval and cannot be ordered with the markings. Slides B Silver Rated 3A @ 125V AC/250V AC W01 Solder Lug/ Quick Connect Terminals Circuit ON 5C Contacts & Terminals D 5 W01 K Mounting Types Keylocks Programmable Illuminated PB Pushbuttons Rockers LP01 A Black C Red F Green DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Tactiles LP0115CCKW015CB White Cap Red LED Tilt SPDT ON-(ON) Circuit Bushing Mount Black Housing Touch Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals POLES & CIRCUIT Supplement Accessories Indicators Plunger Position ( ) = Momentary Connected Terminals Throw & Power/Lamp Schematics Normal Down Normal Down LP0115 ON (ON) 1-3 1-2 LP0125 ON (ON) Pole Model SP DP Note: Terminal markings “COM, NO, NC, L, + and – ” are actually on the switch; terminal numbers are not on the switch. 1 (COM) SPDT 3 1 (COM) D70 1-3 4-6 1-2 www.nkkswitches.com 4-5 DPDT 3 L (+) (-) L L (+) (-) L 2 2 4 6 5 Series LP01 Toggles Short Body Pushbuttons MOUNTING TYPES M Snap-in .681” (17.3mm) Diameter Rockers Bushing .630” (16.0mm) Diameter Recommended Panel Thickness: 0.2 (18.1) +– 0.0 .713 (1.7) +– 0.0 0.1 .067 0.2 (16.0) +– 0.0 Dia .630 Pushbuttons This mounting option is supplied with a steel hexagon nut with nickel plating. Recommended Panel Thickness: 0.1 (7.5) –+ 0.0 .295 .079” ~ .256” (2.0mm ~ 6.5mm) .039” ~ .126” (1.0mm ~ 3.2mm) (17.3) .681 (21.0) Min .827 (25.0) Min .984 Allow .984” (25.0mm) distance from center-to-center between switches when mounted side-by-side. D 0.2 (1.1) +– 0.0 R .043 + 0.2 – 0.0 Dia Allow .827” (21.0mm) distance from center-to-center between switches when mounted side-by-side. K Black Keylocks HOUSING Housing available in black only. The one-piece body and bezel have a matte finish. Solder Lug/ .110” (2.8mm) Quick Connect Power Level 3A @ 125V AC/250V AC; 3A @ 30V DC Epoxy Seal (2.0) .079 (2.8) .110 (0.6) R .024 (1.2) .047 Thk = (0.5) .020 Tactiles Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC, electrical life will be 100,000 operations minimum. (7.3) .287 Slides Silver Contacts Rotaries CONTACT MATERIALS, RATINGS, & TERMINALS W01 LED COLORS & SPECIFICATIONS 5D 5F Red Amber Green Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current IF 20mA 20mA 20mA Forward Voltage VF 1.95V 2.0V 2.1V Maximum Reverse Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆I F 0.41mA/°C 0.29mA/°C 0.39mA/°C No Code –10°C ~ +50°C Supplement Ambient Temperature Range Touch Colors 5C Indicators LEDs are an integral part of the switch and are not available separately. (-) Accessories (+) Tilt The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Single Color LED with 1 Element Programmable Illuminated PB C No Lamp www.nkkswitches.com D71 Series LP01 Toggles Short Body Pushbuttons Rockers CAP COLORS Nonilluminated Cap Cap Color Available: Cap Colors Available: A Pushbuttons Black with Spot Illumination B White Material: Polycarbonate Finish: Matte Spot illuminated, illuminated, and nonilluminated caps are an integral part of the switch and are not available separately. A Black C Red F Green TYPICAL SWITCH DIMENSIONS Bushing Mount Single Pole 3 LP0115CCKW015CB (2.5) .098 (13.6) Dia .535 (20.0) Dia .787 NC 6 L –+ 2 1 COM (7.3) .287 5 (9.7) .382 4 COM (3.0) .118 (5.55) .219 (6.0) .236 (11.1) .437 Single Pole Rotaries 3 1 (21.3) .838 (5.5) .217 L –+ 2 (2.8) Typ .110 NC NO (9.7) .382 Double Pole (3.7) .146 (1.2) x (2.0) Typ .047 x .079 (3.7) .146 (0.5) Typ .020 Double Pole (3.7) .146 (1.2) x (2.0) Typ .047 x .079 M16 P1 4 (6.0) .236 (11.1) .437 Single Pole (3.0) Dia .118 (9.7) .382 5 COM (3.0) .118 (5.55) .219 Bushing Mount & Spot Illumination 6 1 COM (7.3) .287 NC L –+ 2 1 (21.3) .838 (5.5) .217 3 NO NO Slides LP0115CMKW015CB (2.5) .098 (13.6) Dia .535 (20.0) Dia .787 L –+ 2 (2.8) Typ .110 NC NO 3 NO (9.7) .382 (3.7) .146 Touch (3.2) .126 LP0115CCKW015CA 1 6 5 (9.7) .382 4 COM (3.0) .118 (5.55) .219 Snap-in Mount & Spot Illumination NC L –+ 2 COM (7.3) .287 (6.0) .236 (11.1) .437 Single Pole (3.0) Dia .118 3 1 (21.3) .838 (5.5) .217 L –+ 2 (2.8) Typ .110 (2.5) .098 (13.6) Dia .535 (20.0) Dia .787 NC NO (9.7) .382 NO 3 NO Tilt (0.5) Typ .020 NO Tactiles (3.7) .146 (0.5) Typ .020 Snap-in Mount Indicators Double Pole (3.7) .146 (1.2) x (2.0) Typ .047 x .079 M16 P1 NO D NO Programmable Illuminated PB Illuminated Cap Cap Color Available: NO Keylocks Spot Illuminated Cap (1.2) x (2.0) Typ .047 x .079 Double Pole (3.7) .146 (3.7) .146 Supplement (3.2) .126 LP0115CMKW015CA D72 (13.6) Dia .535 (20.0) Dia .787 (2.8) Typ .110 (2.5) .098 (5.5) .217 (7.3) .287 (21.3) .838 www.nkkswitches.com NC L –+ 1 NC 6 L –+ 2 1 COM (3.0) .118 (5.55) .219 3 NO NO 3 2 5 4 COM (6.0) .236 (11.1) .437 NO (9.7) .382 NO Accessories (0.5) Typ .020 (9.7) .382 Series LP01 Toggles Short Body Pushbuttons OPTIONAL ACCESSORIES NO – + (17.0) .669 (3.0) .118 AT718 Single Pole Straight PC Terminals (17.1) .673 NO L AT719 Double Pole Straight PC Terminals NO – + (17.0) .669 COM (3.0) .118 (4.0) .157 (3.0) Typ .118 (17.1) .673 (4.85) Typ .191 D NC NO L (17.0) .669 COM (3.0) Typ .118 (3.7) .146 (5.55) Typ .219 (4.0) .157 (3.7) Typ .146 (3.7) Typ .146 (4.85) Typ .191 (5.55) .219 Material: Glass fiber reinforced polyamide (1.0) Dia Typ .039 (1.85) Typ .073 (3.0) Typ .118 CL (5.55) Typ .219 Note: Order adaptors separately Tactiles CL (4.85) Typ .191 (1.0) Dia Typ .039 (1.85) Typ .073 (3.0) Typ .118 NO – + (3.7) .146 (5.55) .219 NO (3.7) .146 (5.55) Typ .219 NC (4.85) Typ .191 L COM (5.0) .197 (3.7) .146 (5.55) .219 NC NO – + COM (5.0) .197 (4.85) Typ .191 Pushbuttons L Programmable Illuminated PB NO Keylocks NC (4.85) Typ .191 (17.1) .673 Rotaries (17.0) .669 AT717 Double Pole Solder Lug/ Quick Connect Terminals Slides (17.1) .673 AT716 Single Pole Solder Lug/ Quick Connect Terminals Rockers Adaptors Switch Dimensions Shown with Adaptor AT716 Tilt Dimension A: Solder Lug .197” (5.0mm); Straight PC .157” (4.0mm) Panel thickness for LP01 Bushing Mount: .079” ~ .256” (2.0mm ~ 6.5mm) (27.3) 1.075 Touch A LEGENDS Indicators NKK Switches can provide custom legends for caps. Contact factory for more information. Recommended Methods: R PW Accessories Suggested Printable Area for LP01 Cap Epoxy based ink is recommended. Note: Suggested printable area does not apply to spot illuminated cap. www.nkkswitches.com (12.07) Dia .475 (13.6) Dia .535 (0.76) Typ .030 Supplement Pad Print or Laser Etch on cap. Shaded area is printable area D73