Series B
Toggles
Subminiature Fully Illuminated Toggles
A
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section.
Programmable Illuminated PB
Pushbuttons
Other Ratings
Keylocks
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Angle of Throw:
50 milliohms maximum 500 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum 50,000 operations minimum 1.18N Nonshorting (break-before-make) 26°
Materials & Finishes
Slides
Actuator: Bushing Housing: Case Housing: Support Bracket: Movable Contact: Stationary Contacts: Terminals:
Polyamide Polyamide Glass fiber reinforced polyamide Phosphor bronze with tin plating Phosphor bronze with gold plating Brass with tin plating Brass with gold plating
Rotaries
Environmental Data
Tactiles
Operating Temperature Range: Humidity: Vibration: Shock:
–25°C through +55°C (–13°F through +131°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 3 right angled directions, with 5 shocks in each direction)
Tilt
PCB Processing
Touch
Soldering: Cleaning:
Indicators
Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Automated alcohol based cleaning recommended, 5 minutes maximum. Do not use high-purity alcohol (50% alcohol or more) or organic solvent. High alcohol solution can damage clear plastic. See Cleaning specifications in Supplement section.
Standards & Certifications
Supplement
Accessories
The B Series illuminated toggles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A20
www.nkk.com
Subminiature Fully Illuminated Toggles
Series B
A
Toggles Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers
Distinctive Characteristics
LED provides maximum illumination to bushing and actuator, indicating actuator status in highly visible green, red, or amber for single color or red/green for bicolor. (Patent pending.) Totally sealed body construction prevents contact contamination and allows time- and money-saving automated soldering and cleaning. Molded-in, epoxy sealed terminals lock out flux and other contaminants. Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother, positive detent actuation, increased contact stability, and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing.
Actual Size
www.nkk.com
A21
Series B
Toggles
Subminiature Fully Illuminated Toggles
TYPICAL SWITCH ORDERING EXAMPLE
A
Pushbuttons
Rockers
B
Poles
1 SPDT 2
1
Circuits
ON NONE
2
J
Actuator
J
P
P C Terminals
P Straight Right Angle Vertical C D F
C
LEDs
Single Color Red Amber Green Bicolor CF Red/Green ON-NONE-ON & ON-OFF-ON
Programmable Illuminated PB
ON
J
Clear
Combines with single color or bicolor LEDs 3 ON OFF ON Combines with bicolor LED only J
H V
ON-NONE-ON only
Bushing
Clear
Keylocks
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
B12JJPC
Rotaries
Clear Toggle & Bushing with Red LED SPDT ON-NONE-ON Circuit Straight PC Terminals
Tactiles
Slides
P OLE & CIRCUITS
Toggle Position Up Center Down Connected Terminals Up Center Down Throw & Schematics Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external power source.
Tilt
Touch
Pole Model Throw
Slot
Slot
Indicators
SPDT
B12 B13
ON ON
NONE OFF
ON ON
2-3 2-3
NONE OPEN
2-1 2-1
3
2 (COM) 1
(4) Red (5) (6) (5) (6) Green
Single Color
Bicolor
Accessories
ACTUATOR & BUSHING J
Clear Toggle
(6.3) .248 (3.5) .138 26° (1.9) Dia .075
J
Clear Bushing
Supplement
A22
www.nkk.com
Subminiature Fully Illuminated Toggles
LED COLORS & SPECIFICATIONS
LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section.
Single Color
Series B
A
Bicolor
Colors
Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage I FM IF VF VRM
Red 30mA 20mA 1.9V 5V
Amber 30mA 20mA 1.9V 5V
Green 20mA 10mA 3.4V 5V 0.28mA/°C
Red/Green 30mA/20mA 20mA/10mA 1.9V/3.4V 5V/5V 0.43mA/°C/0.28mA/°C
Current Reduction Rate Above 25°C ∆I F Ambient Temperature Range
0.43mA/°C
–25°C ~ +55°C
PC TERMINALS P
Straight
H
Right Angle with Bracket
V
Vertical with Bracket
TYPICAL SWITCH DIMENSIONS
Straight PC
1 4 5 6
4 1 2 3
26° Slot (8.8) .346
2 3
(8.8) .346
5 6
(5.08) .200
Terminal 4 is a support pin on single color models.
B 12JJPC
Right Angle PC
26°
1 4
2 5
3 6
(1.9) Dia .075
6
5
4
Slot (2.7) .106 (6.3) .248 (0.4) .016 (5.08) .200 (16.42) .646 (2.54) .100 (0.5) .020
(0.6) Typ .024
(5.08) .200 (0.6) Dia Typ .024 (2.54) Typ .100 (0.8) Dia Typ .031
(5.08) .200 (8.8) .346
Terminal 4 is a support pin on single color models.
B 13JJHCF
(1.9) Dia .075 (6.0) Dia .236 Slot (0.6) Typ .024 (2.7) .106 (6.3) .248 (0.4) .016 (5.08) .200 (18.96) .746 (0.5) Typ .020 (2.54) Typ .100 (5.08) .200
1 4 5 6
Vertical PC
(3.1) .122
2 3
4 5 6
1 2 3
(2.54) Typ .100 (5.08) .200
Terminal 4 is a support pin on single color models. www.nkk.com
B 13JJVCF A23
Supplement
(5.08) .200 (8.8) .346
(0.6) Dia Typ .024
(0.8) Dia Typ .031
Accessories
26°
(8.8) .346
(5.08) .200
Indicators
Touch
Tilt
(6.0) Dia .236
3
2
1
(3.1) .122
(8.8) .346
(2.54) Typ .100
(2.54) .100
Tactiles
Slides
(3.5) .138 (6.3) .248
(0.8) .031 (13.1) .516
(2.54) Typ .100 (3.1) .122
(0.8) Dia Typ .031
Rotaries
(6.0) Dia .236
(1.9) Dia .075
(0.6) Dia Typ .024
(5.08) .200 (2.54) Typ .100
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
C
D
F
CF
Toggles
很抱歉,暂时无法提供与“B13JJHD”相匹配的价格&库存,您可以联系我们找货
免费人工找货