CB315FP-R

Toggles Series CB3 Rockers General Specifications Pushbuttons Electrical Capacity (Resistive Load) Low/Logic Level: 50mA @ 24V DC maximum Programmable Illuminated PB Other Ratings Keylocks Materials & Finishes Rotaries Slides Tactiles Tilt Touch Indicators Contact Resistance: 100 milliohms maximum Insulation Resistance: 100 megohms minimum @ 250V DC Dielectric Strength: 250V AC minimum between contacts & between contacts & case for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 100,000 operations minimum Nominal Operating Force: 1.57N Total Travel: .010” (.250mm) Actuator: Case: Seal: Base: Movable Contacts: Stationary Contacts: Terminals: Environmental Data J Operating Temperature Range: Humidity: Vibration: Shock: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Polytetrafluoroethylene Polyphthalamide (UL94V-0) Beryllium copper with silver plating Brass with silver plating Brass with silver plating –25°C through +70°C (–13°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Reflow Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: Automated cleaning. See Cleaning Specifications in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 actuator & base The CB3 Series tactiles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Supplement Accessories 6mm Process Sealed SMT Tactiles J8 www.nkkswitches.com Toggles Series CB3 6mm Process Sealed SMT Tactiles Rockers Distinctive Characteristics Pushbuttons Sealed construction prevents contact contamination and allows automated soldering and cleaning. Programmable Illuminated PB .244” (6.2mm) square body allows compact mounting. Heat tolerant resin used for actuator and base meets UL flammability rating of 94V-0 and maintains switch reliability through vapor phase and infrared convection reflow soldering. Rotaries Keylocks Dome contact gives crisp tactile feedback to positively indicate circuit transfer and assures high reliability and long life – more than 100,000 operations. Gull-winged terminals ensure mechanical stability during soldering and simplify solder joint inspection. Packaged in tape-reel or partitioned tray. Tape-reel packaging meets EIA-481-D Standard. J Indicators Touch Tilt Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) Tactiles Slides Insert molded terminals lock out flux, solvents, and other contaminants. Supplement Accessories Actual Size www.nkkswitches.com J9 Series CB3 Toggles 6mm Process Sealed SMT Tactiles TYPICAL SWITCH ORDERING EXAMPLE 15 P F Pushbuttons Rockers CB3 Programmable Illuminated PB Packaging Pole & Circuit 15 SPST OFF Actuator (ON) F ( ) = Momentary Gull Wing for Upright Mount P Flat Button Tape-Reel 1,000 Pieces/Reel R Terminals No Code Partitioned Tray Keylocks DESCRIPTION FOR TYPICAL ORDERING EXAMPLE CB315FP Rotaries Flat Button SPST OFF-(ON) Circuit Slides Gull Wing Terminals for Upright Mount Tactiles POLE & CIRCUIT J Actuator Position ( ) = Momentary Normal Down Model SPST Tilt Pole Switch Throw & Schematic CB315 OFF 3 2 4 Note: Terminal numbers are not actually on switch. (ON) Touch SP 1 Single Pole • Single Throw (3.0) Dia .118 Accessories Indicators TYPICAL SWITCH DIMENSIONS (0.3) Typ .012 (1.7) Typ .067 1 3 (6.2) .244 Supplement (4.35) Dia .171 1 (8.9) .350 (9.0) .354 (6.2) .244 (0.65) .026 4 2 (3.1) .122 CB315FP J10 3 www.nkkswitches.com (4.0) .157 (0.7) Typ .028 4 2 (4.0) .157 (1.4) Typ .056 Series CB3 Toggles 6mm Process Sealed SMT Tactiles PACKAGING No Code Tape-Reel (packaged to EIA-481-D standard) If less than 1,000 pieces are ordered, the switches are packaged in a partitioned tray. No code is required. Programmable Illuminated PB Pushbuttons Switches must be ordered in 1,000-piece increments when tape-reel packaging is selected. Partitioned Tray Rockers R Keylocks Tape-Reel Dimensions & Specifications Each tape-reel of 1,050 pockets contains 1,000 switches Minimum Leader Length: 16.54” (420mm) Minimum Trailer Length: 7.09” (180mm) (4.0) Typ .157 (6.7) Typ .264 (0.4) .016 Direction of Feed (16.4) .646 KEYBOARD MATRIX J Common Bus Matrix 5 4 6 10 6 4 7 8 9 3 11 8 A B 0 1 2 12 1 2 3 4 5 6 7 8 9 0 A B 3 2 1 P C Te r m i n a t i o n s 1 2 3 4 5 6 7 8 9 10 11 12 13 1 5 4 6 2 7 8 9 6 A B 0 7 = ON 5 7 Red = PCB Trace 4 P C Te r m i na t i ons 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 0 A B = ON 3 Black = Switch Circuit www.nkkswitches.com J11 Touch 13 Keys (Switches) 3 2 1 Indicators 9 5 These single pole, single throw switches can be arranged on a single-sided PC board matrix with strapped terminals to achieve an X-Y type electrical interconnection. Keys (Switches) These single pole, single throw switches can be used in a keyboard matrix and, using strapped terminals, achieve a common bus electrical configuration on a single-sided PC board. Tilt X-Y Matrix Accessories (2.0) .079 (21.0) Dia .827 (9.4) .370 Supplement Overall Dia (330.0) 13.0 (7.5) (16.0) .295 .630 (3.4) .134 (3.8) .150 Slides (78.49) Dia 3.090 (13.0) Dia .512 (2.0) Typ .079 (1.5) Dia Typ .059 Rotaries (12.0) Typ .472 Tactiles (2.0) Typ .079 (1.75) .069