EB2011

Toggles Series EB General Specifications Rockers Pushbuttons Programmable Illuminated PB Keylocks Light Touch Miniature Pushbuttons Electrical Capacity (Resistive Load) C Power Level (silver): Logic Level (gold): 3A @ 125V AC for silver contacts 0.4VA maximum @ 28V AC/DC maximum for gold contacts (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts and case for 1 minute minimum 100,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold Single Pole: 2.35N for Momentary and 2.65N for Alternate Action Double Pole: 2.94N for Momentary and 3.63N for Alternate Action Momentary: Pretravel .047” (1.2mm); Overtravel .016” (0.4mm); Total Travel .063” (1.6mm) Alternate: Pretravel .071” (1.8mm); Overtravel .016” (0.4mm); Total Travel .087” (2.2mm) Slides Rotaries Materials & Finishes Plunger: Bushing: Frame: Case: Movable Contacts: Stationary Contacts: Terminals: Brass with nickel plating Brass with nickel plating Stainless steel Melamine phenolic resin (UL94V-0) Copper with silver or gold plating Silver & copper with silver or gold plating Copper with silver or gold plating Operating Temp Range: Humidity: Vibration: Shock: –10°C through +70°C (+14°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Tilt Tactiles Environmental Data Touch Standards & Certifications Supplement Accessories Mounting Torque: Cap Installation Force: Soldering Time & Temp: Cleaning: Indicators Installation 1.47Nm (13.0 lb • in) for double nut; 0.68Nm (6.0 lb • in) for single nut 78.5N (17.65 lbf) maximum downward force on actuator Wave Solder (Straight PC): See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. Flammability Standards: UL94V-0 case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” before first dash in part number to order UL recognized switch. All single and double pole models recognized at 3A @ 125V AC. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” before first dash in part number to order CSA certified switch. Single pole solder lug and PC models certified at 3A @ 125V AC; double pole PC models certified at 3A @ 125V AC. C24 www.nkkswitches.com Toggles Series EB Rockers Distinctive Characteristics Power and logic level capabilities available to suit varying applications. Bushing and snap-in mount versions available; snap-in models offer many style and color choices to enhance front panel appearance. Programmable Illuminated PB C Pushbuttons Light Touch Miniature Pushbuttons Light touch actuation. High torque bushing prevents rotation and separation from metal frame during installation. Keylocks Stainless steel frame resists corrosion. Case of heat resistant resin meets UL 94V-0 flammability rating. Rotaries Higher insulating barriers protect against crossover in double pole devices. Slides 1,500V dielectric strength between contacts and case is accomplished by clinching the frame away from the terminals. Tilt Tactiles Epoxy sealed terminals prevent entry of solder flux and other contaminants. Snap-in Mount Page C30 Accessories Page C26 Supplement Bushing Mount Indicators Touch Actual Size www.nkkswitches.com C25 Series EB Toggles Light Touch Miniature Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE 65 B F C Poles & Circuits Programmable Illuminated PB Pushbuttons Rockers EB20 Caps 11 SPDT ON (ON) B .315” (8.0mm) Dia. 65 SPDT ON ON C .394” (10.0mm) Dia. 61 DPDT ON (ON) 85 DPDT ON ON ( ) = Momentary Silver Contacts; Solder Lug Terminals 3A @ 125V AC A Black B White G Gold Contacts; Solder Lug Terminals 0.4VA max @ 28V AC/DC max C Red Silver Contacts; Straight PC Terminals; 3A @ 125V AC E Yellow P F Green G Blue H Gray Rotaries Keylocks No Code Slides PG Gold Contacts; Straight PC Terminals 0.4VA max @ 28V AC/DC max IMPORTANT: Tilt Tactiles Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Touch EB2065-BF Indicators Green .315” (8.0mm) Diameter Cap Accessories SPDT ON-ON Circuit Supplement Silver Contacts & Solder Lug Terminals with 3-Amp Rating C26 Colors Contacts, Ratings, & Terminals www.nkkswitches.com Series EB Toggles Light Touch Miniature Pushbuttons POLES & CIRCUITS Normal Down Note: Terminal numbers are not actually on the switch. Pole Model SP EB2011 EB2065 ON ON (ON) ON 2-3 2-1 SPDT DP EB2061 EB2085 ON ON (ON) ON 2-3 5-6 2-1 5-4 DPDT Keyway Rockers Down Throw & Switch Schematics Keyway 2 (COM) 3 2 C 1 (COM) 3 1 5 6 4 CONTACT MATERIALS, RATINGS, & TERMINALS Solder Lug Silver Contacts Power Level 3A @ 125V AC G Solder Lug Gold Contacts Logic Level 0.4VA max @ 28V AC/DC max Rotaries Keylocks No Code Pushbuttons Normal Connected Terminals Programmable Illuminated PB Plunger Position ( ) = Momentary Complete explanation of operating range in Supplement section. Slides (2.0) .079 Epoxy Seal (2.0) .079 Tactiles (4.0) (1.1) .157 .043 Thk (0.7) (0.5) Com .028 .020 Straight PC Silver Contacts Power Level PG Straight PC Gold Contacts Logic Level 3A @ 125V AC Tilt P Touch 0.4VA max @ 28V AC/DC max Indicators Complete explanation of operating range in Supplement section. PCB Footprints Single Pole (6.4) (4.3) .252 .169 Double Pole (1.2) .047 Thk (0.7) (0.5) Com .028 .020 2 (3.9) Typ .154 1 (1.8) Dia Typ .071 www.nkkswitches.com 3 6 2 5 1 4 Accessories (4.7) .185 3 (3.9) Typ .154 (1.8) Dia Typ .071 Supplement Epoxy Seal C27 Series EB Toggles Light Touch Miniature Pushbuttons CAPS & COLORS AT443 .315” (8.0mm) Diameter Snap-on Cap C Cap Colors Available: A C B AT442 .394” (10.0mm) Diameter Snap-on Cap Cap Colors Available: F Black White G C Red H E Yellow A Green (7.6) .299 (8.0) Dia .315 Gray Black F Green B White G Blue C Red H Gray E Yellow Blue Cap Material: Polycarbonate Finish: Glossy (8.0) .315 (10.0) Dia .394 Cap Material: Polycarbonate Finish: Glossy Plunger Extension Due to a difference in plunger lengths on the momentary and alternate action models, cap distance from top of bushing varies. Keylocks Programmable Illuminated PB Pushbuttons Rockers B (2.3) Dia .091 (2.3) Dia .091 (2.85) Dia .112 (8.0) .315 (3.3) Dia .130 Rotaries (2.5) .098 (2.7) .106 Momentary Cap Location Slides (9.3) .366 (1.2) .047 (1.4) .055 Momentary Plunger Length (2.85) Dia .112 Alternate Plunger Length Alternate Cap Location TYPICAL SWITCH DIMENSIONS Tactiles Solder Lug Single Pole M6 P0.75 Keyway (8.0) Dia .315 (1.4) .055 (7.6) .299 Touch (7.0) .276 3 COM 2 (0.5) .020 Tilt (11.0) .433 (1.1) x (2.0) Typ .043 x .079 (0.7) Typ .028 (3.9) Typ .154 (4.5) (6.8) .177 .268 (8.5) (18.0) .335 .709 For Momentary Devices 1 (4.0) Typ .157 (2.0) Typ .079 EB2011-BA Indicators Solder Lug Double Pole Keyway M6 P0.75 Accessories (11.0) .433 (8.0) Dia .315 Supplement (11.7) .461 (0.5) .020 (1.4) .055 (7.6) .299 (4.5) (6.8) .177 .268 (8.5) (18.0) .335 .709 For Momentary Devices EB2061-BA C28 (1.1) x (2.0) Typ .043 x .079 (0.7) Typ .028 (3.9) Typ .154 www.nkkswitches.com COM 6 3 5 2 4 1 (4.0) Typ .157 (4.7) .185 (2.0) Typ .079 Series EB Toggles Light Touch Miniature Pushbuttons HARDWARE Face Nut Lockwasher AT513M Metric Hexagon Nut AT509 Lockwasher AT507M Metric Locking Ring Material: Brass with Nickel Plating Material: Steel with Zinc/Chromate Material: Steel with Zinc/Chromate Locking Ring (Optional) Lock Nut C (6.0) Dia .236 M6 P0.75 Optional Hardware: AT507M Metric Locking Ring Rockers 2 AT513M Metric Hexagon Nuts 1 AT509 Internal Tooth Lockwasher Optional Hardware (8.0) .315 (6.4) Dia (10.2) Dia .252 .402 (12.0) Dia .472 (2.0) .079 (5.5) .217 (9.0) .354 (0.5) .020 (1.5) .059 (1.7) .067 (0.8) .031 Keylocks Note: Cap must be snapped on after the switch is mounted into the panel. PANEL CUTOUTS & THICKNESSES (5.6) .220 M6 P0.75 (1.7) .067 (6.35) Dia .250 (0.6) .024 Maximum Effective Panel Thickness: .118” (3.0mm) (6.5) Dia .256 (2.2) Dia .087 Rotaries (6.5) .256 Maximum Effective Panel Thickness: .055” (1.4mm) Maximum Effective Panel Thickness: .185” (4.7mm) Indicators Touch Tilt See Accessories & Hardware section for optional Conical Nuts: AT512M used with cap AT443 and AT512CM used with cap AT442. Accessories (2.5) .098 (8.5) .335 (6.35) Dia .250 Supplement (0.8) .031 Without Bottom Hex Nut Slides (8.0) Dia .315 With Standard Hardware & Optional Locking Ring Tactiles With Standard Hardware Metric Bushing Pushbuttons Standard Hardware Programmable Illuminated PB Installation/Assembly www.nkkswitches.com C29