GW22LCH

Ultra-Thin Rockers Series GW Distinctive Characteristics Various colored rockers and paddles. Combination of dust cover and closely fit housing, actuator, and interior pivot provides protection for contacts. Detent mechanism design of coil spring, plunger, and plastic detent results in crisp and positive actuation. Extremely thin size allows high density PCB mounting and makes these switches ideal for handheld equipment. Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother, positive detent actuation, increased contact stability and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) Molded-in, epoxy sealed terminals lock out flux and other contaminants. .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing for straight and angle mounting. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Ultra-Thin Rockers Series GW General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Angle of Throw: 80 milliohms maximum 500 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 50,000 operations minimum 50,000 operations minimum For Rockers 1.70N; for Paddles 1.30N 28° Materials & Finishes Actuator: Case: Sealing Ring: Movable Contact: Stationary Contacts: Base: Mounting Bracket: Terminals: Glass fiber reinforced polyamide (UL94V-0) Glass fiber reinforced polyamide (UL94V-0) Nitrile butadiene rubber Phosphor bronze with gold plating Phosphor bronze with gold plating Glass fiber reinforced polyamide (UL94V-0) Phosphor bronze with tin plating Phosphor bronze with gold plating Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: –30°C through +85°C (–22°F through +185°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Cleaning: Wave Soldering Recommended: See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section.. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL Recognition or CSA Certification: UL94V-0 actuator & case/base The GW Series rockers have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Ultra-Thin Rockers TYPICAL SWITCH ORDERING EXAMPLE Series GW P PC TERMINALS P H V Straight Right Angle Vertical GW POLES 1 2 SPDT DPDT 2 ON 1 2 ACTUATORS R B C H White Red Gray C ACTUATOR COLORS CIRCUIT NONE ON R L Rocker Paddle DESCRIPTION FOR TYPICAL ROCKER ORDERING EXAMPLE GW12RCP Red Rocker Cap Straight PC Terminals SPDT ON-NONE-ON Circuit P OLES & CIRCUIT Rocker Position Up Pole SP DP Model GW12 GW22 ON ON NONE NONE ON ON 5-6 5-6 2-3 OPEN OPEN 5-4 5-4 2-1 Center Down Up Connected Terminals Center Down Throw & Schematics Note: Terminal numbers are not actually on the switch. SPDT DPDT 4 5 (COM) 4 5 (COM) 6 1 6 2 3 TYPICAL SWITCH DIMENSIONS Straight PC (0.25) Typ .010 (3.0) .118 (1.35) .053 P/N This Side (0.4) Dia Typ .016 Single Pole 1 4 5 3 6 (7.0) .276 28° (2.54) Typ .100 (4.5) .177 (2.3) .091 (7.0) .276 (2.6) .102 (2.54) .100 4 5 6 (2.54) Typ .100 (0.25) Typ .010 (2.54) .100 (0.6) Dia Typ .024 GW12RCP On single pole models positions 1 & 3 are support pins. (0.25) Typ .010 (3.0) .118 Straight PC Double Pole P/N This Side (0.4) Dia Typ .016 28° (2.54) Typ .100 1 2 3 4 5 6 (7.0) .276 (2.54) .100 4 5 6 1 2 3 (2.54) Typ .100 (2.6) .102 (0.25) Typ .010 (4.5) .177 (3.8) .150 (7.0) .276 (2.6) .102 (2.54) .100 (0.6) Dia Typ .024 GW22LCP N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Ultra-Thin Rockers TYPICAL SWITCH DIMENSIONS Right Angle PC 28° Series GW Single Pole (0.25) .010 (5.15) .203 (2.9) .114 (7.0) .276 (3.0) .118 P/N This Side (4.5) .177 (2.75) .108 (0.25) .010 (5.08) .200 (7.68) .302 6 5 4 (2.54) Typ .100 4 (0.6) Dia Typ .024 5 6 (5.08) .200 (0.5) Typ .020 (5.08) .200 (7.5) .295 (2.3) .091 (0.4) Dia Typ .016 (2.54) Typ .100 GW12RCH Right Angle PC 28° (7.0) .276 (3.0) .118 (2.6) .102 Double Pole (0.25) .010 (5.15) .203 (2.9) .114 P/N This Side 3 2 1 (4.5) .177 (2.75) .108 (0.25) .010 (5.08) .200 (10.22) .402 (0.5) .020 (2.54) .100 6 5 4 (2.54) Typ .100 1 4 2 5 3 6 (2.54) .100 (5.08) .200 (0.6) Dia Typ .024 (0.5) Typ .020 GW22LCH (5.08) .200 (7.5) .295 (3.8) .150 (0.4) Dia Typ .016 (2.54) Typ .100 Vertical PC (0.25) Typ .010 (4.5) .177 (1.35) .053 Single Pole P/N This Side 4 (7.65) .301 (4.15) .163 28° (2.75) .108 5 6 (2.54) .100 4 5 6 (2.54) Typ .100 (5.08) .200 C L (0.5) Typ .020 (2.54) .100 (0.25) .010 (5.0) .197 (2.3) .091 GW12RCV (5.08) .200 (12.76) .502 (0.5) Typ .020 (2.54) Typ .100 (0.6) Dia Typ .024 (0.4) Dia .016 (1.27) .050 Vertical PC (0.25) Typ .010 (4.5) .177 Double Pole P/N This Side 1 2 3 4 5 6 (7.65) .301 (4.15) .163 28° (2.75) .108 (2.54) .100 4 5 6 1 2 3 (2.54) Typ .100 (5.08) .200 (0.5) Typ .020 (2.54) .100 (0.25) .010 (5.0) .197 (3.8) .150 (5.08) .200 (12.76) .502 (0.5) Typ .020 (2.54) Typ .100 (0.6) Dia Typ .024 (0.4) Dia .016 (2.54) .100 GW22LCV N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07