HB15CKW01-G

Subminiature Pushbuttons Series HB Distinctive Characteristics Compact front panel design with 9mm square or round bezel. Rear panel threaded mounting. Behind panel depth of less than one inch. 8mm body diameter fits common size panel cutout. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Dual, sliding contacts with self-cleaning action provide contact stability, high reliability, and increased operating life. Solder lug terminals have spacing of .100” (2.54mm) for choice of mounting. Longer normally closed terminal facilitates wiring and soldering. Molded-in terminals lock out flux, dust, and other contaminants. Illuminated models available and shown in the Illuminated Pushbutton section. Matching indicators available and shown at the end of Section M. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Subminiature Pushbuttons Series HB General Specifications Electrical Capacity (Resistive Load) Power Level (code W): 0.1A maximum @ 30V AC/DC Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum 50,000 operations minimum 3.43N Nonshorting (break before make) Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm) Materials & Finishes Housing: Base: Movable Contact: Stationary Contacts: Terminals: Glass fiber reinforced polyamide Glass fiber reinforced polyamide Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Environmental Data Operating Temp Range: Humidity: Vibration: Shock: –25°C through +70°C (–13°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Mounting Torque: Cap Installation Force: Soldering Time & Temperature: 0.49Nm (4.34 lb • in) maximum for round mounting nut 9.8N (2.2 lbf) maximum downward force on cap Manual Soldering: See Profile A in Supplement section. Standards & Certifications UL & C-UL Recognized: R All models recognized at 0.1A @ 30V AC/DC; UL File No. WOYR2.E44145; add “/U” to end of part number to order UL mark on switch. C-UL File No. WOYR8.E44145; add “/C-UL” to end of part number to order C-UL mark on switch. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Subminiature Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series HB A HB POLE 1 SPDT 1 5 SHAPES S C Square Round S K W01 CONTACTS & TERMINALS W01 Silver Contacts and Solder Lug Terminals 0.1A @ 30V AC/DC CIRCUITS 5 6 ON ON (ON) ON K ( ) = Momentary Alternate Action with Latchdown HOUSING Black only A B C E F G CAP COLORS Black (Square only) White Red Yellow Green Blue IMPORTANT: Switches are supplied without UL & C-UL markings unless specified. Specific models & ratings noted on General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE HB15SKW01-A Black Cap Square Shape SPDT ON-(ON) Circuit Silver Contacts and Solder Lug Terminals; rated 0.1A @ 30V AC/DC Black Housing POLES & CIRCUITS Plunger Position ( ) = Momentary Normal Pole SP Model HB15 *HB16 ON ON (ON) ON 1-3 1-2 Down Connected Terminals Normal Down Throw & Schematic Note: Switch is marked with NO, NC, C, L. 1 (COM) SPDT 3 2 * When in latchdown position for the alternate circuit, cap position is .051” (1.3mm) above the built-in bezel. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Subminiature Pushbuttons SHAPES & PANEL CUTOUT S .354” (9.0mm) Square Series HB C .354” (9.0mm) Round Recommended Panel Thickness: .020 ~ .197” (0.5 ~ 5.0mm) (8.0) Dia .315 The bezel is an integral part of the switch body. Socket wrench AT110 may be used for mounting. Overtightening the mounting nut AT073 may damage the switch housing. H OUSING K Housing available in black only. CONTACT MATERIALS, RATINGS, & TERMINALS W01 Silver Contacts (5.0) .197 (2.0) .079 (1.0) .039 (1.8) .071 Power Level PCB Mounting 0.1A maximum @ 30V AC/DC Thk = (0.3) .012 Solder lug terminals are spaced .100” x .200” (2.54mm x 5.08mm). This enables PCB mounting which can be accomplished by elongating PC board holes to .080” (2.03mm). CAP TYPES & COLORS Cap Colors Available: Black (Square only) White AT4035 Square Green Blue (4.8) .189 (7.4) Sq .291 (4.5) .177 A B C E Red Yellow F G AT4036 Round (4.8) .189 (7.4) Dia .291 (4.5) .177 Material: Polycarbonate Finish: Glossy TYPICAL SWITCH DIMENSIONS Square Single Pole M8P0.75 (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 (1.8) .071 (5.0) .197 (7.0) .276 L(+) L(-) NO NC COM 2 3 1 (2.54) Typ .100 (7.4) Sq .291 (9.0) Sq .354 (1.3) .051 (3.5) .138 (0.5) (5.0) .020 .197 (10.0) .394 (15.5) (5.3) .610 .209 Latchdown Position (2.54) Typ .100 HB15SKW01-C Round Single Pole M8P0.75 (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 (1.8) .071 (5.0) .197 (7.0) .276 L(+) L(-) NO NC COM 2 3 1 (2.54) Typ .100 (7.4) Dia .291 (9.0) Dia .354 (1.3) .051 (3.5) .138 (0.5) (5.0) .020 .197 (10.0) .394 (5.3) (15.5) .209 .610 Latchdown Position (2.54) Typ .100 HB16CKW01-C N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07