HB16SKW01-5C-DB

Subminiature Pushbuttons Series HB Distinctive Characteristics Full face and spot illumination available. Front panel relamping. Choice of super bright LEDs in white, green, and blue in addition to bright red, amber, and green LEDs. Compact front panel design with 9mm square or round bezel options. Rear panel threaded mounting. Behind panel depth of less than one inch. 8mm body diameter fits common size panel cutout. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Dual, sliding contacts with self-cleaning action provide contact stability, high reliability, and increased operating life. Solder lug terminals have spacing of .100” (2.54mm) for choice of mounting. Longer normally closed terminal facilitates wiring and soldering. Molded-in terminals lock out flux, dust, and other contaminants. Nonilluminated models available and shown in the Pushbutton section. Matching indicators available and shown at the end of Section M. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Subminiature Pushbuttons Series HB General Specifications Electrical Capacity (Resistive Load) Power Level (code W): 0.1A maximum @ 30V AC/DC Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum 50,000 operations minimum 3.43N Nonshorting (break before make) Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm) Materials & Finishes Housing: Base: Movable Contact: Stationary Contacts: Common Terminal: End Terminals: Lamp Terminals: Glass fiber reinforced polyamide Glass fiber reinforced polyamide Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Environmental Data Operating Temp Range: Humidity: Vibration: Shock: –25°C through +50°C (–13°F through +122°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Mounting Torque: Cap Installation Force: Soldering Time & Temperature: 0.49Nm (4.34 lb • in) maximum for round mounting nut 9.8N (2.2 lbf) maximum downward force on cap Manual Soldering: See Profile A in Supplement section. Standards & Certifications UL & C-UL Recognized: R All models recognized at 0.1A @ 30V AC/DC; UL File No. WOYR2.E44145; add “/U” to end of part number to order UL mark on switch. C-UL File No. WOYR8.E44145; add “/C-UL” to end of part number to order C-UL mark on switch. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Subminiature Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series HB JB HB POLE 1 SPDT 1 5 S K W01 6G H OUSING K Black only CIRCUITS 5 6 ON ON (ON) ON ( ) = Momentary Alternate Action with Latchdown CONTACTS & TERMINALS Silver Contacts and W01 Solder Lug Terminals 0.1A @ 30V AC/DC SHAPES S C Square Round 5C 5D 5F LEDS Bright Red Amber Green AB CB DB FB JB Super Bright 6B 6F 6G White Green Blue JB CAP TYPES & COLORS LED Cap: Lens/Diffuser Color Black Cap/White Window for Spot Illuminaterd (Square only) Red/White Amber/White Green/White Clear/White LED Cap: Lens/Diffuser Color Clear/White IMPORTANT: Switches are supplied without UL & C-UL markings unless specified. Specific models & ratings noted on General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE HB15SKW01-6G-JB Blue, Super Bright LED White Cap Square Shape Black Housing SPDT ON-(ON) Circuit Silver Contacts and Solder Lug Terminals; rated 0.1A @ 30V AC/DC 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Subminiature Pushbuttons POLES & CIRCUITS Plunger Position ( ) = Momentary Normal Pole SP Model HB15 *HB16 ON ON (ON) ON 1-3 1-2 SPDT 3 Series HB Connected Terminals Normal Down Notes: Throw & Switch/Lamp Schematics Switch is marked with NO, NC, C, L. LED circuit is isolated and requires external power source. 1 (COM) (+) (-) Down 2 * When in latchdown position for the alternate circuit, cap position is .051” (1.3mm) above the built-in bezel. S HAPES S C .354” (9.0mm) Square .354” (9.0mm) Round The bezel is an integral part of the switch body. The bezel is an integral part of the switch body. Panel Cutout & Mounting Recommended Panel Thickness: .020 ~ .197” (0.5 ~ 5.0mm) (8.0) Dia .315 Overtightening the mounting nut AT073 may damage the switch housing. H OUSING K Housing available in black only. CONTACT MATERIALS, RATINGS, & TERMINALS W01 Silver Contacts Power Level 0.1A maximum @ 30V AC/DC Solder Lug (5.0) .197 (2.0) .079 (1.0) .039 (1.8) .071 PCB Mounting Solder lug terminals are spaced .100” x .200” (2.54mm x 5.08mm). This enables PCB mounting which can be accomplished by elongating PC board holes to .080” (2.03mm). 03-07 Thk = (0.3) .012 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Subminiature Pushbuttons LED COLORS & SPECIFICATIONS Series HB The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Single element LED is colored in OFF state. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Bright AT633 Super Bright AT624G Blue AT629B White AT630F Green T-1 Bi-pin Note for Super Bright: (+) (-) Electrostatic Sensitive Devices Attention Bright Super Bright 5C Red 30 20 1.85 5 0.40 5D Amber 30 20 2.0 5 0.42 –25° ~ +50°C 5F Green 25 20 2.2 5 0.38 6B White 30 20 3.6 5 0.50 6F Green 30 20 3.5 5 0.50 6G Blue 30 20 3.6 5 0.50 Unit mA mA V V mA/°C Color I FM IF VF VRM ∆I F Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range –25° ~ +50°C CAP TYPES & COLORS Color Codes: A Black B White C Red D Amber F Green J Clear Colored Cap for Bright LEDs Cap Colors Available: (7.4) Sq .291 (4.8) .189 (4.6) .181 (1.8) .071 (1.2) .047 (3.0) .118 AB Black Cap with Translucent White Window for LED Display AT4052 Spot Illuminated Square only Material: Polycarbonate Finish: Matte Lens/Diffuser Colors Available: AT4166 Square (7.4) Sq .291 (4.5) .177 (4.8) .189 (4.8) .189 AT4167 Round (7.4) Dia .291 (4.5) .177 Transparent Colored Lens Translucent White Diffuser Colored LED AT633 CB DB FB Red/White Amber/White Green/White Material: Polycarbonate Finish: Glossy White Cap for Bright & Super Bright LEDs JB Clear Lens/ White Diffuser AT4031 Square (7.4) Sq .291 (4.5) .177 (4.8) .189 AT4032 Round (7.4) Dia .291 (4.5) .177 (4.8) .189 Transparent Clear Lens Translucent White Diffuser Colored LEDs AT624, AT629, AT630, or AT633 03-07 Material: Polycarbonate Finish: Glossy N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Subminiature Pushbuttons T YPICAL SWITCH DIMENSIONS Square Single Pole M8P0.75 (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 (1.8) .071 (5.0) .197 (7.0) .276 Series HB L(+) L(-) NO NC COM 2 3 1 (2.54) Typ .100 (7.4) Sq .291 (9.0) Sq .354 (1.3) .051 (3.5) .138 (0.5) (5.0) .020 .197 (10.0) .394 (15.5) (5.3) .610 .209 Latchdown Position (2.54) Typ .100 HB15SKW01-5C-CB Round Single Pole M8P0.75 (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 (1.8) .071 (5.0) .197 (7.0) .276 L(+) L(-) NO NC COM 2 3 1 (2.54) Typ .100 (7.4) Dia .291 (9.0) Dia .354 (1.3) .051 (3.5) .138 (0.5) (5.0) .020 .197 (10.0) .394 (5.3) (15.5) .209 .610 Latchdown Position (2.54) Typ .100 HB16CKW01-5C-CB ASSEMBLY INSTRUCTIONS Cap Removal 1. Have cap in extended position (not latchdown) for alternate action models. 2. Use the grip slots on the sides of the cap and pull it out of the switch. LED Polarity & Orientation in Lamp Socket For AT624, AT629, AT630: Insert the LED with the D flat opposite the black dot molded inside the switch lamp socket. For AT633: Insert the LED with the Black Dot on the terminal to the right. Cap Replacement 1. Match the prongs on the cap base with the projections in the switch, at the same time aligning the spring clips on the cap with the indentations in the switch. 2. Press firmly in place. D Flat Black Dot (+) (–) (+) (–) AT624 AT629 AT630 AT633 Top View of Switch Anode (+) Cathode (–) Electrostatic Sensitive Devices Attention Super Bright LEDs AT624, AT629, & AT630 are electrostatic sensitive. AT111 Lamping Tool Lamping Tool AT111 may be used to remove and replace LED. AT110 Socket Wrench Socket Wrench AT110 may be used to tighten the mounting nut. 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com