HB16SKW01-5F-CB

Series HB Toggles Subminiature Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 0.1A maximum @ 30V AC/DC Pushbuttons Other Ratings Programmable Illuminated PB D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum 50,000 operations minimum 3.43N Nonshorting (break before make) Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm) Materials & Finishes Rotaries Housing: Base: Movable Contact: Stationary Contacts: Common Terminal: End Terminals: Lamp Terminals: Glass fiber reinforced polyamide Glass fiber reinforced polyamide Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Keylocks Slides Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Tactiles –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Tilt Mounting Torque: Cap Installation Force: Soldering Time & Temperature: 0.49Nm (4.34 lb • in) maximum for round mounting nut 9.8N (2.2 lbf) maximum downward force on cap Manual Soldering: See Profile A in Supplement section. Touch Standards & Certifications UL: Supplement Accessories Indicators File No. E44145 All models recognized at 0.1A @ 30V AC/DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch. D12 www.nkk.com Subminiature Pushbuttons Series HB Toggles Full face and spot illumination available. Front panel relamping. Choice of super bright LEDs in white, green, and blue in addition to bright red, amber, and green LEDs. Compact front panel design with 9mm square or round bezel options. Rear panel threaded mounting. Behind panel depth of less than one inch. 8mm body diameter fits common size panel cutout. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Dual, sliding contacts with self-cleaning action provide contact stability, high reliability, and increased operating life. Solder lug terminals have spacing of .100” (2.54mm) for choice of mounting. Longer normally closed terminal facilitates wiring and soldering. Molded-in terminals lock out flux, dust, and other contaminants. Matching indicators available. Tilt Tactiles Pushbuttons D Actual Size Indicators www.nkk.com D13 Supplement Accessories Touch Slides Rotaries Keylocks Programmable Illuminated PB Rockers Distinctive Characteristics Series HB Toggles Subminiature Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons Rockers HB Pole 1 SPDT 1 S C 5 Shapes Square Round S K W01 6G JB Contacts & Terminals Silver Contacts and W01 Solder Lug Terminals * 0.1A @ 30V AC/DC Programmable Illuminated PB D Circuits 5 6 ON ON (ON) ON K ( ) = Momentary Alternate Action with Latchdown Housing Black only 5C 5D 5F LEDs Bright Red Amber Green Cap Types & Colors LED Cap: Lens/Diffuser Color AB CB DB FB JB Black Cap/White Window for Spot Illuminated (Square only) Red/White Amber/White Green/White Clear/White LED Cap: Lens/Diffuser Color JB Clear/White Rotaries Keylocks * Wire harness & cable assemblies offered only in Americas Super Bright 6B 6F 6G White Green Blue Slides Tactiles IMPORTANT: Switches are supplied without UL & cULus markings unless specified. Specific models & ratings noted on General Specifications page. Nonilluminated No Nonilluminated Code A B C E F G Nonilluminated Cap Colors Black (Square Only) White Red Yellow Green Blue Touch Tilt DESCRIPTION FOR TYPICAL ORDERING EXAMPLE HB15SKW01-6G-JB Indicators Blue, Super Bright LED Square Shape White Cap Accessories SPDT ON-(ON) Circuit Black Housing Silver Contacts & Solder Lug Terminals; rated 0.1A @ 30V AC/DC Supplement D14 www.nkk.com Subminiature Pushbuttons POLES & CIRCUITS Plunger Position ( ) = Momentary Normal Pole Model Down Connected Terminals Normal Down Notes: Series HB Throw & Switch/Lamp Schematics Switch is marked with NO, NC, C, L. LED circuit is isolated and requires external power source. 1 (COM) (+) (-) SP HB15 *HB16 ON ON (ON) ON 1-3 1-2 SPDT 3 2 * When in latchdown position for the alternate circuit, cap position is .051” (1.3mm) above the built-in bezel. D SHAPES & PANEL CUTOUT S C .354” (9.0mm) Square .354” (9.0mm) Round Panel Cutout & Mounting Recommended Panel Thickness: .020 ~ .197” (0.5 ~ 5.0mm) H OUSING K Housing available in black only. Tilt CONTACT MATERIALS, RATINGS, & TERMINALS W01 Silver Contacts Power Level 0.1A maximum @ 30V AC/DC (5.0) .197 (2.0) .079 (1.0) .039 (1.8) .071 Thk = (0.3) .012 www.nkk.com D15 Supplement Solder lug terminals are spaced .100” x .200” (2.54mm x 5.08mm). This enables PCB mounting which can be accomplished by elongating PC board holes to .080” (2.03mm). Accessories Solder Lug PCB Mounting Indicators Touch Tactiles (8.0) Dia .315 Overtightening the mounting nut AT073 may damage the switch housing. Slides Rotaries The bezel is an integral part of the switch body. The bezel is an integral part of the switch body. Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series HB Toggles Subminiature Pushbuttons LED COLORS & SPECIFICATIONS Rockers The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Single element LED is colored in OFF state. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Bright AT633 Note for Super Bright: ATTENTION Bright Super Bright Pushbuttons ELECTROSTATIC SENSITIVE DEVICES 5C Red 30 20 1.85 5 0.40 5D Amber 30 20 2.0 5 0.42 5F Green 25 20 2.2 5 0.38 6B White 30 20 3.6 5 0.50 6F Green 30 20 3.5 5 0.50 6G Blue 30 20 3.6 5 0.50 Unit mA mA V V mA/°C Super Bright (+) (-) Color I FM IF VF VRM ∆I F Programmable Illuminated PB D AT624G Blue AT629B White AT630F Green T-1 Bi-pin Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range No Lamp –25° ~ +50°C –25° ~ +50°C Keylocks No Code CAP TYPES & COLORS Color Codes: A Black B White C Red D Amber E Yellow F Green G Blue (7.4) Sq .291 Rotaries J Clear (1.8) .071 (1.2) .047 (3.0) .118 Cap Colors Available: Colored Cap for Bright LEDs Square only Material: Polycarbonate Finish: Matte AT4167 Round AT4052 Spot Illuminated Slides AB Black Cap with Translucent White Window for LED Display (4.8) .189 (4.6) .181 Lens/Diffuser Colors Available: Tactiles AT4166 Square CB DB FB Red/White Amber/White Green/White (4.8) .189 (7.4) Sq .291 (4.5) .177 (7.4) Dia .291 (4.5) .177 Transparent Colored Lens Translucent White Diffuser Colored LED AT633 Transparent Clear Lens Translucent White Diffuser Colored LEDs AT624, AT629, AT630, or AT633 (4.8) .189 Tilt Material: Polycarbonate Finish: Glossy White Cap for Bright & Super Bright LEDs Touch JB Clear Lens/ White Diffuser AT4031 Square (7.4) Sq .291 (4.5) .177 AT4032 Round (7.4) Dia .291 (4.5) .177 Indicators Material: Polycarbonate Finish: Glossy (4.8) .189 (4.8) .189 Accessories Nonilluminated Caps Cap Colors Available: A B D16 Black (Square Only) White C E Red Yellow F G Green Blue AT4035 Square (4.8) .189 (7.4) Sq .291 (4.5) .177 AT4036 Round (7.4) Dia .291 (4.5) .177 Supplement (4.8) .189 Material: Polycarbonate Finish: Glossy www.nkk.com Subminiature Pushbuttons TYPICAL SWITCH DIMENSIONS Single Pole M8P0.75 (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 (1.8) .071 (5.0) .197 (7.0) .276 L(+) L(-) NO NC COM 2 3 1 Series HB Square Rockers Toggles (2.54) Typ .100 (7.4) Sq .291 (9.0) Sq .354 (1.3) .051 (3.5) .138 (0.5) (5.0) .020 .197 (10.0) .394 (15.5) (5.3) .610 .209 Latchdown Position HB15SKW01-5C-CB D Single Pole M8P0.75 (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 (1.8) .071 (5.0) .197 (7.0) .276 L(+) L(-) NO NC COM 2 3 1 Round (2.54) Typ .100 (7.4) Dia .291 (9.0) Dia .354 (1.3) .051 (3.5) .138 (5.0) (0.5) .197 .020 (10.0) .394 (5.3) (15.5) .209 .610 Latchdown Position (2.54) Typ .100 HB16CKW01-5C-CB Cap Removal 1. Have cap in extended position (not latchdown) for alternate action models. 2. Use the grip slots on the sides of the cap and pull it out of the switch. LED Polarity & Orientation in Lamp Socket For AT624, AT629, AT630: Insert the LED with the D flat opposite the black dot molded inside the switch lamp socket. For AT633: Insert the LED with the Black Dot on the terminal to the right. Cap Replacement 1. Match the prongs on the cap base with the projections in the switch, at the same time aligning the spring clips on the cap with the indentations in the switch. 2. Press firmly in place. D Flat Black Dot (+) (–) (+) (–) Anode (+) Cathode (–) ELECTROSTATIC SENSITIVE DEVICES ATTENTION Super Bright LEDs AT624, AT629, & AT630 are electrostatic sensitive. AT111 Lamping Tool Lamping Tool AT111 may be used to remove and replace LED. AT110 Socket Wrench Socket Wrench AT110 may be used to tighten the mounting nut. www.nkk.com D17 Supplement Accessories Indicators Touch AT624 AT629 AT630 AT633 Top View of Switch Tilt Tactiles Slides ASSEMBLY INSTRUCTIONS Rotaries Keylocks Programmable Illuminated PB (2.54) Typ .100 Pushbuttons