ISC15ANP4

Toggles OLED Pushbutton & Display DISTINCTIVE CHARACTERISTICS E Keylocks Programmable Illuminated PB Pushbuttons Rockers • • • • • • • • • • • • • Organic LED technology Life 30,000 hours @ 100cd/m2 (based on 40% pixels on) or 60,000 hours @ 50cd/m2 (based on 40% pixels on) Power consumption only 3.8mA (30% less than previous product) Range of 65,536 colors in 16 bit mode, 256 colors in 8 bit mode Full viewing angle of 180° Exceptional contrast: 50 times greater than LCD products Four times more enhanced resolution High resolution provides sharp, clear images of very small characters Operated by commands and data supplied via serial communications (SPI) Distinct, long travel of 4.5mm (same as KP01 series pushbuttons) Dust tight construction Stylish, translucent black housing design Viewing area: 15.5mm x 11.6mm (horizontal x vertical) Rotaries High reliability and long life of three million actuations minimum High resolution of 64RGB x 48 pixels Slides Epoxy sealed straight PC terminals Tactiles Snap-in standoff for easy, secure mounting and alignment Viewing area: 12.9mm x 9.9mm (horizontal x vertical) Tilt High resolution of 52RGB x 36 pixels Touch Bracket has crimped legs to ensure secure PC mounting and prevent dislodging during wave soldering Supplement Accessories Indicators Actual Sizes Switch E8 Display www.nkkswitches.com 10/03/19 OLED Pushbutton Toggles ATTENTION SWITCH PART NUMBER & DESCRIPTION Part Number Switch Description OLED Pixel Format ISC15ANP4 SPST, Momentary ON Gold Contacts Straight PC Terminals Color OLED Display Module 65,536 Colors 64RGB x 48 Pixels Horizontal x Vertical Rockers ELECTROSTATIC SENSITIVE DEVICES Circuit SPST normally open Contact Position Leave actuator: 1 – 2 OFF Push actuator: 1 – 2 ON Electrical Capacity (Resistive Load) 100mA @ 12V DC Contact Resistance 200 milliohms maximum @ 20mV 10mA Insulation Resistance 100 megohms minimum @ 100V DC Dielectric Strength 125V AC for 1 minute minimum Mechanical Endurance 3,000,000 operations minimum Electrical Endurance 3,000,000 operations minimum Operating Force 2.0 ± 0.5 Newtons Total Travel 4.5mm (.177”) E Keylocks OLED SPECIFICATIONS Characteristics of Display Color OLED display module Display Mode Passive matrix Viewing Area 15.5mm x 11.6mm (horizontal x vertical) Pixel Format 64RGB x 48 pixels (horizontal x vertical) Pixel Size 0.21mm x 0.20mm (horizontal x vertical) Interface Serial (SPI) interface Number of Colors 65,536 Colors (16bit: R 5bit/G 6bit/B 5bit) or 256 Colors (8bit: R 2bit/G 3bit/B 3bit) Operating Temperature Range –20°C ~ +70°C (–4°F ~ +158°F) Storage Temperature Range –30°C ~ +80°C (–22°F ~ +176°F) Operating Life (Display) 30,000 hours @ 100cd/m2 (based on 40% pixels ON) 60,000 hours @ 50cd/m2 (based on 40% pixels ON) Absolute Maximum Ratings Recommended Operating Conditions 2.4V 2.8V 3.5V VCC 15.0V 16.0V 17.0V VI H 0.8 x VDD –– –– VI L –– –– 0.2 x VDD VDD VCC –0.0V to +19.0V Supply Voltage for Drive VI –0.3V to VD D +0.3V Input High Level Voltage Input Low Level Voltage Optical Characteristics (Temperature at 25°C, Initial Value: 87 x 0F) (Temperature at 25°C, VDD = 2.8V, VCC = 16.0V) Items Symbols Min Typical Max 4.6mA Items All-Pixels-On Mode *Drive System Power Current I CC1 –– All-Pixels-On Mode *Logic/IF System Power Current I DD1 –– 0.16mA 0.19mA White Color Coordinate Sleep Mode **Drive System Power Current I CC2 –– Red Color Coordinate Sleep Mode **Logic/IF System Power Current I DD2 –– Slides Maximum –0.3V to +4.0V Current Consumption Tactiles Typical Tilt Input Voltage Symbols Minimum Touch Supply Voltage for Drive Items Supply Voltage for Logic/Interface 3.8mA –– –– 10μA 10μA * All pixels shall be turned on with the maximum level gray scale ** All pixels shall be turned off (while chip is operating) Luminosity Green Color Coordinate Blue Color Coordinate (x) (y) (x) (y) (x) (y) (x) (y) Contrast Ratio www.nkkswitches.com Min Typical Max Unit Remarks 75 100 125 cd/m2 White (All pixels on) 0.26 0.32 0.63 0.29 0.19 0.61 0.10 0.14 100 0.30 0.37 0.67 0.33 0.23 0.65 0.14 0.20 –– 0.34 0.42 0.71 0.37 0.27 0.69 0.18 0.26 –– –– –– –– –– –– –– –– –– –– Indicators VDD Ratings Accessories Symbols Supplement Items Rotaries Display Device Supply Voltage for Logic/Interface Programmable Illuminated PB Pushbuttons SWITCH SPECIFICATIONS E9 Toggles OLED Pushbutton SWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Rockers Color OLED Panel 64RGB x 48 COM1....COM48 Segment Driver Common Driver Pushbuttons OLED Driver with Controller VDD 3 VCC 9 RES 5 SEG/COM Driving Block Gray Scale Decoder E SCK 7 SS 4 SDI 8 D/C 6 Oscillator Graphic Display Data RAM 96 x 64 x 16 Bit Display Timing Generator Command Decoder MCU Interface ISC15ANP4 GND 10 Slides Rotaries Pin No. Symbol Name SW SW VDD SS Terminal of Switch Terminal of Switch Power Slave Select Normally open Normally open Power source for logic circuit Slave select for SPI. This line is active low. 5 RES Reset Reset signal input. When pin is low, initialization of chip is executed. 6 D/C Data/Command 7 8 SCK SDI VCC GND Serial Clock Serial Data In Power Ground Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. Clock line for SPI that synchronizes command and data Data input line for SPI Power source for drive circuit Connect to Ground TYPICAL SWITCH DIMENSIONS Tilt See Pixel Detail Terminal numbers are not on the switch. (3.3) .130 (13.41) .528 (18.0) .709 Standoff 1 Standoff 2 (0.6) Typ .024 Touch (20.59) .811 (9.57) .377 See Standoff Detail Indicators (15.5) .610 (23.0) .906 (23.13) .911 Accessories Pixel Detail Supplement (0.03) Typ .0012 E10 (16.0) .630 (0.4) Typ .016 (0.74) .029 (0.20) Typ .0079 (1.0) Typ .039 2 (11.6) .457 (0.21) Typ .0083 (0.03) Typ .0012 See Pixel Detail A Pixel Detail A (0.20) .0079 (0.17) .0067 (0.04) Typ .0016 (0.07) Typ .0028 Standoff Detail 4 1 Standoff 1 (8.0) .315 (2.0) Dia .079 Dimension A Standoff 1 = (2.7) Standoff 2 = (2.3) .091 .106 (0.2) Typ .008 (2.0) .079 (7.05) .278 2x (0.9) Dia .035 (18.0) .709 Footprint A (7.0) .276 3 (0.3) Typ .012 R G B R www.nkkswitches.com 9 Standoff 2 (1.25) .049 R 10 (7.62) .300 (3.4) .134 (0.2) .008 (0.21) .0083 SW Function 1 2 3 4 9 10 Tactiles 2 1 SW Keylocks Programmable Illuminated PB SR1,SG1,SB1......SR64, SG64,SB64 (1.0) Typ .039 (7.0) .276 9 3 2 10 (7.62) .300 4 1 8x (0.75) Dia .029 (2.0) .079 (7.05) .278 (8.0) .315 (16.0) .630 4x (1.3) Dia .051 Landless Toggles OLED Pushbutton & Display TIMING SPECIFICATIONS FOR SWITCH & DISPLAY Maximum Clock Cycle Time t c yc le 150ns –– –– D/C Setup Time t AS 40ns –– –– D/C Hold Time t AH 40ns –– –– SS Setup Time t CSS 75ns –– –– SS Hold Time t CSH 60ns –– –– Write Data Setup Time t DSW 40ns –– –– Write Data Hold Time t DHW 40ns –– –– SS t AS tA H t CSS t CS H tR t CLKH Pushbuttons D/C t cy cl e SCK t CLKL tF t DSW t DH W D7 t CLKL 75ns –– –– SCK High Time t CLKH 75ns –– –– SCK Rise Time tR –– –– 15ns SCK Fall Time tF –– –– 15ns D6 D5 D4 D3 D2 D1 D0 E Keylocks SDI SCK Low Time Rotaries STATE TRANSITION 7 : Initialization 4 : Display OFF 8 : Changing the Display VC C VD D Changing the Display 0 Power OFF OFF –– OFF OFF Disable 1 Display OFF OFF ON ON ON Enable 2 Display ON ON OFF ON ON Enable Display Sleep Power ON/OFF Sequence Initialization Setting State 0 State 1 State 2 State Transition Transition 1 Power ON 2 Power OFF Refer to 3 Display ON "Power ON/OFF Sequence" 4 Display OFF 7 Initialization Initialize Setting of Command/Data Image Rewriting Send Display Data Display Settings Dimmer, Scroll, etc. Power OFF State 0 Minimum 0µs Minimum 0µs VDD 8 Power ON 0V Index Reset low pulse width Trw (minimum 3µs) RES “L” or “Hi-z” “L” or “Hi-z” Minimum 3µs Indicators State 8 : Changing the Display Minimum 0µs VCC D/C SS “L” or “Hi-z” SCK SDI VDD level (due to ESD protection circuit between VDD and VCC) “H” or “L” “L” or “Hi-z” Supplement State Number State 2 Display ON Slides 3 : Display ON Tactiles 2 : Power OFF State 1 Display OFF (Sleep Mode) Touch 1 : Power ON, 7 : Initialization State 0 Power OFF (VCC, VDD O FF) Programmable Illuminated PB Typical Tilt Symbols Minimum Note: Refer to Application Notes on web site. www.nkkswitches.com Accessories Items Rockers AC Characteristics (Temperature at 25°C), VDD = 2.4V ~ 3.5V) E13 Toggles OLED Pushbutton & Display PRECAUTIONS FOR HANDLING & STORAGE OF OLED PUSHBUTTONS & DISPLAY Rockers ELECTROSTATIC SENSITIVE DEVICES Pushbuttons 1. The IS Series OLED devices are electrostatic sensitive. To avoid damage to IC, do not touch terminals unless properly isolated from static electricity. 2. Signal input under conditions not recommended may cause damage to the OLED unit or deterioration of the display. Follow directions regarding supply sequences of power and signal voltages. 3. If the OLED panel is broken, avoid touching the contents. Wash off any contact to the skin or clothing. 4. Limit operating force to switch keytop to 100.0N maximum, as excessive pressure may damage the OLED. 5. For OLED display, it is necessary for bracket legs to be Grounded. 6. Recommended soldering time and temperature limits for OLED switch or display: E Avoid temperatures exceeding 80°C at the OLED. Wave Soldering: see Profile A in Supplement section. Manual Soldering: see Profile A in Supplement section. 7. The IS series OLED devices are not process sealed. Keylocks Programmable Illuminated PB ATTENTION Handling Rotaries 8. Pixels acquire diminished brightness over time and use, and those most frequently habituated have greater reduction of brightness than those less used. To minimize this difference, operate OLED unit so that all pixels are used as consistently as possible. Slides 9. For switch, clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. For display, avoid contact with any flux or detergent. If any liquids spill on display surface, immediately wipe with soft absorbent cloth. 10. Proper serial resistors and buffers for signals should be used to prevent noise problems. Tactiles Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. Supplement Accessories Indicators Touch Tilt 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. E14 www.nkkswitches.com Toggles Optional Accessories OPTIONAL ACCESSORIES AT9704-085K Socket for LCD 64 x 32 Pushbutton Rockers Materials: IS15EBFP4RGB • The socket permits the switch to be plugged in after automated processing. Pushbuttons Programmable Illuminated PB Keylocks Long Travel LCD 64 x 32 Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper • Use of the socket enables easy field replacement of the device. 2 9 (20.3) .799 (6.0) .236 (7.62) .300 8 (6.0) .236 3 (0.5) Dia Typ .020 E (22.9) .902 (1.0) Typ .039 (4.6) .181 (7.4) .291 (8.0) .315 (7.05) .278 AT9704-085L Socket for OLED Pushbutton 1 4 (1.0) Typ .039 9x (0.75) Dia .030 (7.05) .278 (2.0) .079 (2.0) .079 (7.62) .300 (8.0) .315 Compatible Part Numbers for AT9704-085L Materials: OLED Pushbutton Frameless OLED ISC15ANP4 ISF15ACP4 Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper • The socket permits the OLED switch to be plugged in after automated processing. • Use of the socket enables easy field replacement of the device. Slides Rotaries Compatible Part Number for AT9704-085K (7.0) .276 Tactiles (7.62) .300 (0.5) Dia Typ .020 (4.2) .165 (7.0) .276 (8.0) .315 (7.05) .278 (2.0) .079 4 3 1 (7.62) .300 10x (0.75) Dia .030 (1.0) Typ .039 (2.0) .079 (7.05) .278 (8.0) .315 Tilt (22.9) .902 (1.0) Typ .039 (7.0) .276 2 10 9 (20.3) .799 Compatible Part Number for AT9704-085M AT9704-085M Socket for OLED Display OLED Display Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper ISC01P • The socket permits the OLED display to be plugged in after automated processing. • Use of the socket enables easy field replacement of the device. (16.8) .661 Accessories Indicators Touch Materials: (16.8) .661 7 (10.0) .394 (17.6) .693 (7.0) .276 (1.0) Typ .039 Supplement (0.5) DiaTyp .020 (19.9) .783 E50 (5.25) .207 (7.25) .285 (4.4) .173 (7.2) .283 www.nkkswitches.com (7.0) .276 (1.0) Typ .039 (2.0) .079 1 8 2 (10.0) .394 12x (0.75) Dia .030 (5.25) .207