ISF15ACP4

Toggles Frameless OLED Pushbutton DISTINCTIVE CHARACTERISTICS Rockers • Range of 65,536 colors in 16 bit mode Pushbuttons • Maximum use of display lens with ultra-thin frame provides full screen capacity Programmable Illuminated PB • High definition, contrast and resolution of 96RGB x 64 pixels in compact screen and minimal frame • Smooth operation with short stroke of 0.07” lends to tactile feedback unparalleled to touch panels • Operating life of 50,000 hours minimum • Multiple units easily combine to form one screen, offering flexibility in size and layout • Same outer dimensions of switch and footprint, enabling ease of replacement with current switches • Operated by commands and data supplied via serial communications (SPI) E • Incorporates bitmap display function • Low energy consumption Keylocks • Dust tight construction Slides Rotaries • Snap-in standoff for easy, secure mounting and alignment; aids in prevention of dislodging during wave soldering Tactiles Viewing area: 21.28mm x 18.7mm (horizontal x vertical) High reliability and long life of one million actuations minimum Tilt Highly reliable gold plated twin contacts Touch Epoxy sealed straight PC terminals Supplement Accessories Indicators Actual Size E4 www.nkkswitches.com 10/03/19 Frameless OLED Pushbutton Toggles ATTENTION SWITCH PART NUMBER & DESCRIPTION Part Number Switch Description OLED Pixel Format ISF15ACP4 SPST, Momentary ON Gold Contacts Straight PC Terminals Color OLED Display Module 65,536 Colors 96RGB x 64 Pixels Horizontal x Vertical Rockers ELECTROSTATIC SENSITIVE DEVICES Circuit SPST normally open Contact Position Leave actuator: 1 – 2 OFF Push actuator: 1 – 2 ON Electrical Capacity (Resistive Load) 100mA @ 12V DC (resistive circuit) Contact Resistance 200 milliohms maximum @ 20mV 10mA Insulation Resistance 100 megohms minimum @ 100V DC Dielectric Strength 125V AC for 1 minute minimum Mechanical Endurance 1,000,000 operations minimum Electrical Endurance 1,000,000 operations minimum Operating Force 2.0 ± 0.5 Newtons Total Travel 1.8mm (0.07”) Keylocks E OLED SPECIFICATIONS Characteristics of Display Color OLED display module Display Mode Passive matrix Viewing Area 21.28mm x 18.74mm (horizontal x vertical) Pixel Format 96RGB x 64 pixels (horizontal x vertical) Pixel Size 0.222mm x 0.293mm (horizontal x vertical) Interface Serial (SPI) interface Number of Colors 65,536 Colors (16bit: R 5bit/G 6bit/B 5bit) or 256 Colors (8bit: R 2bit/G 3bit/B 3bit) Operating Temperature Range –20°C ~ +70°C (–4°F ~ +158°F) Storage Temperature Range –30°C ~ +80°C (–22°F ~ +176°F) Operating Life (Display) 50,000 hours @ 100cd/m2 (based on 40% pixels ON; Ta = 77°F) Absolute Maximum Ratings Recommended Operating Conditions Items Tactiles Slides Symbols Minimum Typical Maximum VDD –0.3V to +4.0V Supply Voltage for Logic/Interface VDD 2.4V 2.8V 3.5V Supply Voltage for Drive VCC –0.0V to +19.0V Supply Voltage for Drive VCC 14.0V 15.0V 16.0V Input Voltage VI –0.3V to VD D +0.3V Input High Level Voltage VI H 0.8 x VDD –– –– Input Low Level Voltage VI L –– –– 0.2 x VDD Current Consumption Optical Characteristics (Temperature at 25°C, Initial Value: 87 x 0F) Min Max All-Pixels-On Mode *Drive System Power Current I CC1 –– 11.0mA 13.2mA Luminosity All-Pixels-On Mode *Logic/IF System Power Current I DD1 –– 0.17mA 0.20mA White Color Coordinate Sleep Mode **Drive System Power Current I CC2 –– –– 10μA Sleep Mode I **Logic/IF System Power Current DD2 –– –– 10μA * All pixels shall be turned on with the maximum level gray scale ** All pixels shall be turned off (while chip is operating) Red Color Coordinate Green Color Coordinate Blue Color Coordinate (x) (y) (x) (y) (x) (y) (x) (y) Contrast Ratio www.nkkswitches.com Min Typical Max Unit Remarks 80 105 130 cd/m2 White (All pixels on) 0.26 0.31 0.62 0.30 0.24 0.59 0.10 0.10 100 0.30 0.36 0.66 0.34 0.29 0.63 0.15 0.17 –– 0.34 0.41 0.70 0.38 0.33 0.67 0.19 0.23 –– –– –– –– –– –– –– –– –– –– Accessories Typical Items Symbols Supplement (Temperature at 25°C, VDD = 2.8V, VCC = 15.0V) Items Tilt Supply Voltage for Logic/Interface Touch Ratings Indicators Symbols Rotaries Display Device Items Programmable Illuminated PB Pushbuttons SWITCH SPECIFICATIONS E5 Toggles Frameless OLED Pushbutton BLOCK DIAGRAM & PIN CONFIGURATIONS Color OLED Panel 96RGB x 64 Rockers SR1, SG1, SB1......SR96, SG96,SB96 Segment Driver Common Driver OLED Driver with Controller Pushbuttons Programmable Illuminated PB COM1....COM64 VDD 3 VCC 9 SEG/COM Driving Block Gray Scale Decoder E ISF15ACP4 RES 5 SCK 7 SS 4 SDI 8 D/C 6 Keylocks Rotaries Slides Symbol Display Timing Generator Command Decoder MCU Interface 2 1 Name SW SW VDD SS Terminal of Switch Terminal of Switch Power Slave Select Normally open Normally open Power source for logic circuit Slave select for SPI. This line is active low. 5 RES Reset Reset signal input. When pin is low, initialization of chip is executed. 6 D/C Data/Command 7 8 SCK SDI VCC GND Serial Clock Serial Data In Power Ground Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. Clock line for SPI that synchronizes command and data Data input line for SPI Power source for drive circuit Connect to Ground TYPICAL SWITCH DIMENSIONS Terminal numbers are not on the switch. (3.3) .130 Tilt Part No. This Side (18.0) .709 Standoff 1 (0.6) .024 Touch (0.4) .016 Indicators See Standoff Detail (23.13) .911 (23.0) .906 Accessories R Pixel Detail (.293) .0115 (.263) .0104 Supplement (.074) .0029 (.044) .0017 E6 (7.62) (16.0) .300 .630 Standoff Detail R G B (0.2) .008 Footprint (2.0) Dia .079 Dimension A Standoff 1 = (2.7) Standoff 2 = (2.3) .091 .106 www.nkkswitches.com (7.05) .278 (8.0) .315 (2.0) .079 (18.0) .709 (1.0) Typ .039 9 3 2x (0.9) Dia .035 2 10 4 1 8x (0.75) Dia .030 (2.0) .079 (7.0) .276 Standoff 1 (0.3) Typ .012 (7.0) .276 (.222) .0087 1 A (1.25) .049 (1.0) Typ .039 9 8 7 6 5 4 3 Standoff 2 (3.4) .134 R Standoff 2 10 2 (18.74) .738 (20.59) .811 (21.28) .838 SW Function 1 2 3 4 9 10 Tactiles Graphic Display Data RAM 96 x 64 x 16 Bit GND 10 SW Pin No. Oscillator (7.05) .278 (8.0) .315 (7.62) .300 (16.0) .630 4x (1.3) Dia .051 Landless Toggles Frameless OLED Pushbutton TIMING SPECIFICATIONS Maximum Clock Cycle Time t c yc le 150ns –– –– D/C Setup Time t AS 40ns –– –– D/C Hold Time t AH 40ns –– –– SS Setup Time t CSS 75ns –– –– SS Hold Time t CSH 60ns –– –– Write Data Setup Time t DSW 40ns –– –– Write Data Hold Time t DHW 40ns –– –– SCK Low Time t CLKL 75ns –– –– SCK High Time t CLKH 75ns –– –– SCK Rise Time tR –– –– 15ns SCK Fall Time tF –– –– 15ns SS t AS t AH t CSS t CSH tR t CLKH Pushbuttons D/C t cycle SCK t CLKL tF t DSW t DHW D7 SDI D6 D5 D4 D3 D2 D1 D0 Keylocks E Rotaries STATE TRANSITION 5 : Initialization 3 : Display ON 4 : Display OFF 6 : Display Switch State VC C VD D Changing the Display 0 Power OFF OFF –– OFF OFF Disable 1 Display OFF OFF ON ON ON Enable 2 Display ON ON OFF ON ON Enable Display Sleep Initialization Setting State 0 Power ON State 1 State 2 VDD Transition Index 1 Power ON 2 Power OFF Refer to 3 Display ON "Power ON/OFF Sequence" 4 Display OFF 5 Initialization Initialize Setting of Command/Data Image Rewriting Send Display Data Display Settings Dimmer, Scroll, etc. Power OFF State 0 Minimum 0µs Minimum 0µs State Transition 6 Power ON/OFF Sequence 0V Reset low pulse width Trw (minimum 3µs) RES “L” or “Hi-z” “L” or “Hi-z” Minimum 3µs Minimum 0µs VCC D/C SS “L” or “Hi-z” SCK SDI www.nkkswitches.com VDD level (due to ESD protection circuit between VDD and VCC) “H” or “L” “L” or “Hi-z” Supplement State Number 6 : Display Switch Tactiles 2 : Power OFF State 2 Display ON Slides State 1 Display OFF (Sleep Mode) Tilt State 0 Power OFF (VCC, VDD O F F ) Touch 1 : Power ON, 5 : Initialization Programmable Illuminated PB Typical Indicators Symbols Minimum Accessories Items Rockers AC Characteristics (Temperature at 25°C), VDD = 2.4V ~ 3.5V) E7 Toggles OLED Pushbutton & Display PRECAUTIONS FOR HANDLING & STORAGE OF OLED PUSHBUTTONS & DISPLAY Rockers ELECTROSTATIC SENSITIVE DEVICES Pushbuttons 1. The IS Series OLED devices are electrostatic sensitive. To avoid damage to IC, do not touch terminals unless properly isolated from static electricity. 2. Signal input under conditions not recommended may cause damage to the OLED unit or deterioration of the display. Follow directions regarding supply sequences of power and signal voltages. 3. If the OLED panel is broken, avoid touching the contents. Wash off any contact to the skin or clothing. 4. Limit operating force to switch keytop to 100.0N maximum, as excessive pressure may damage the OLED. 5. For OLED display, it is necessary for bracket legs to be Grounded. 6. Recommended soldering time and temperature limits for OLED switch or display: E Avoid temperatures exceeding 80°C at the OLED. Wave Soldering: see Profile A in Supplement section. Manual Soldering: see Profile A in Supplement section. 7. The IS series OLED devices are not process sealed. Keylocks Programmable Illuminated PB ATTENTION Handling Rotaries 8. Pixels acquire diminished brightness over time and use, and those most frequently habituated have greater reduction of brightness than those less used. To minimize this difference, operate OLED unit so that all pixels are used as consistently as possible. Slides 9. For switch, clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. For display, avoid contact with any flux or detergent. If any liquids spill on display surface, immediately wipe with soft absorbent cloth. 10. Proper serial resistors and buffers for signals should be used to prevent noise problems. Tactiles Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. Supplement Accessories Indicators Touch Tilt 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. E14 www.nkkswitches.com Toggles Optional Accessories OPTIONAL ACCESSORIES AT9704-085K Socket for LCD 64 x 32 Pushbutton Rockers Materials: IS15EBFP4RGB • The socket permits the switch to be plugged in after automated processing. Pushbuttons Programmable Illuminated PB Keylocks Long Travel LCD 64 x 32 Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper • Use of the socket enables easy field replacement of the device. 2 9 (20.3) .799 (6.0) .236 (7.62) .300 8 (6.0) .236 3 (0.5) Dia Typ .020 E (22.9) .902 (1.0) Typ .039 (4.6) .181 (7.4) .291 (8.0) .315 (7.05) .278 AT9704-085L Socket for OLED Pushbutton 1 4 (1.0) Typ .039 9x (0.75) Dia .030 (7.05) .278 (2.0) .079 (2.0) .079 (7.62) .300 (8.0) .315 Compatible Part Numbers for AT9704-085L Materials: OLED Pushbutton Frameless OLED ISC15ANP4 ISF15ACP4 Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper • The socket permits the OLED switch to be plugged in after automated processing. • Use of the socket enables easy field replacement of the device. Slides Rotaries Compatible Part Number for AT9704-085K (7.0) .276 Tactiles (7.62) .300 (0.5) Dia Typ .020 (4.2) .165 (7.0) .276 (8.0) .315 (7.05) .278 (2.0) .079 4 3 1 (7.62) .300 10x (0.75) Dia .030 (1.0) Typ .039 (2.0) .079 (7.05) .278 (8.0) .315 Tilt (22.9) .902 (1.0) Typ .039 (7.0) .276 2 10 9 (20.3) .799 Compatible Part Number for AT9704-085M AT9704-085M Socket for OLED Display OLED Display Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper ISC01P • The socket permits the OLED display to be plugged in after automated processing. • Use of the socket enables easy field replacement of the device. (16.8) .661 Accessories Indicators Touch Materials: (16.8) .661 7 (10.0) .394 (17.6) .693 (7.0) .276 (1.0) Typ .039 Supplement (0.5) DiaTyp .020 (19.9) .783 E50 (5.25) .207 (7.25) .285 (4.4) .173 (7.2) .283 www.nkkswitches.com (7.0) .276 (1.0) Typ .039 (2.0) .079 1 8 2 (10.0) .394 12x (0.75) Dia .030 (5.25) .207