JB15LPF-E

Low Profile Process Sealed Tactiles Series JB Distinctive Characteristics Choice of dimensions from PCB to top of cap adds to design flexibility. Bright, full-face illumination with red, green, or yellow LEDs for attractive, functional panel layouts. Higher operating force type provides more pronounced operating feel. Dome contact gives crisp tactile feedback to positively indicate circuit transfer and assures high reliability and long life of up to 5,000,000 operations. Rubber seal construction prevents contact contamination and allows automated soldering and cleaning. Slanted terminals provide a spring type action which ensures secure mounting and prevents dislodging during wave soldering. Molded-in terminals are part of the sealed construction which allows automated soldering and cleaning. Terminal spacing conforms to standard .100” (2.54mm) PCB grid. Actual Size Common Bus Matrix These single pole, single throw switches can be used in a keyboard matrix and, using strapped terminals, achieve a common bus electrical configuration on a single-sided PC board. 5 1 2 9 3 13 X-Y Matrix These single pole, single throw switches can be arranged on a single-sided PC board matrix with strapped terminals to achieve an X-Y type electrical interconnection. 1 2 3 1 4 5 6 2 7 8 Keys (Switches) 4 7 3 8 6 11 8 12 9 9 6 A 1 2 0 B A 0 B 7 = ON 5 4 3 7 Blue = PCB Trace Black = Switch Circuit 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Keys (Switches) 4 5 6 10 1 2 3 4 5 6 7 8 9 0 A B P C Te r m i n a t i o n s 1 2 3 4 5 6 7 8 9 10 11 12 13 P C Te rminations 1 234 567 1 2 3 4 5 6 7 8 9 0 A B = ON Low Profile Process Sealed Tactiles Series JB General Specifications Electrical Capacity (Resistive Load) Low Level: 50mA @ 24V DC maximum for Standard Operating Force models 125mA @ 24V DC maximum for High Operating Force models Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Total Travel: Standard Operating Force 50 milliohms maximum 500 megohms minimum @ 250V DC 250V AC minimum for 1 minute minimum 5,000,000 operations minimum 5,000,000 operations minimum 1.76N for JB15L .010” (.254mm) High Operating Force 50 milliohms maximum 500 megohms minimum @ 250V DC 250V AC minimum for 1 minute minimum 1,000,000 operations minimum 1,000,000 operations minimum 2.65N for JB15HL & JB15HB .012” (.300mm) Materials & Finishes Actuator: Case: Seal: Base: Movable Contacts: Stationary Contacts: Terminals: Polyacetal for Short; Glass fiber reinforced PBT for Extended Glass fiber reinforced polyamide (UL94V-0) Nitrile butadiene rubber Glass fiber reinforced PBT (UL94V-0) Beryllium copper with silver plating Brass with silver plating Brass with silver plating Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: –25°C through +70°C (–13°F through +158°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Cleaning: Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Automated cleaning. See Cleaning specifications in Supplement section. Standards & Certifications Flammability Standards: UL Recognition or CSA Certification: UL94V-0 rated case & base The JB Series tactiles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Process Sealed Tactiles TYPICAL SWITCH ORDERING EXAMPLE Series JB JB POLE & CIRCUIT 15 SPST OFF (ON) ( ) = Momentary 15 L P TERMINALS C JC CAP TYPES & COLORS Flat Cap Colors B C E F Translucent White Red Yellow Green ACTUATORS L B Short Extended (H operating force only) P Straight PC LED COLORS OPERATING FORCE No Code H Standard (L actuator only) High C E F Red Yellow Green Flat Cap Lens/Diffuser Colors JB JC JE JF Clear/White Clear/Red Clear/Yellow Clear/Green For JC, JE & JF, diffuser color must match LED color DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Framed Cap Button/Frame Colors BB BC BE Red LED Short Actuator SPST OFF-(ON) Circuit Flat Cap with Clear Lens and Red Diffuser Standard Operating Force Straight PC Terminals BF BH White/White White/Red White/Yellow White/Green White/Gray JB15LPC-JC POLE & CIRCUIT Actuator Position ( ) = Momentary Pole & Throw SPST Normal Model JB15 OFF (ON) Down 1 3 (+) (-) Switch Throw & Schematic LED Schematic Notes: Terminal numbers are shown on switch. LED circuit is isolated & requires external power source. SPST 2 4 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Process Sealed Tactiles OPERATING FORCE No Code Standard Nominal Operating Force 1.76N Available with short actuator only (code L) Series JB H High Nominal Operating Force 2.65N Available with both short and extended actuators ACTUATORS L Short Actuator (4.9) .193 (11.2) .441 (12.7) .500 (12.7) Typ .500 (3.0) .118 (3.1) .122 Custom keyboards can be designed with caps installed through a panel cutout (illustration with cap AT4060). B Extended Actuator (3.3) .130 (8.4) .331 (3.2) .126 (14.7) .579 (12.7) .500 (3.1) .122 (12.7) Typ .500 High operating force only Custom keyboards can be designed with caps installed through a panel cutout (illustration with cap AT4076). TERMINALS P Straight PC Terminals (0.8) Typ .031 (0.3) Typ .012 3+ 1 (5.08) .200 (3.1) Typ .122 (5.08) Typ .200 (2.54) Typ .100 (10.16) .400 4 2 Further details in Typical Switch Dimensions C L (1.0) Dia Typ .039 (5.08) .200 LED COLORS & SPECIFICATIONS LEDs are supplied as an integral part of illuminated devices and are not available separately. LED polarity markings are on the bottom of the switch. The electrical specifications shown here are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. C Color Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range I FM IF VF VRM ∆I F Red 25mA 20mA 2.0V 4V E Yellow 25mA 20mA 2.2V 4V 0.42mA/°C –25°C ~ +70°C F Green 25mA 20mA 2.1V 4V N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Process Sealed Tactiles SNAP-ON CAPS AT4135 Flat Cap Color Codes: Series JB (7.3) .287 B C Translucent White Red E F Yellow Green Material: Polycarbonate Finish: Frosted (12.0) Sq .472 AT4060 Flat Lens/Diffuser Color Codes: (6.3) .248 Framed: AT4076 Button with Frame Translucent Button/Frame Color Codes: (6.3) .248 (12.0) Sq .472 (12.3) Sq .484 JB JC JE JF Clear/Translucent White Clear/Red Clear/Yellow Clear/Green Translucent White or Colored Diffuser White Frame Transparent Clear Lens BB BC BE BF BH White/White White/Red White/Yellow White/Green White/Gray Button Finish: Frosted Translucent Clear Button Translucent White Filter Opaque White or Colored Frame Material: Polycarbonate Lens Finish: Glossy Material: Polycarbonate TYPICAL SWITCH DIMENSIONS Flat Snap-on Cap (8.5) .335 (0.4) .016 Short Actuator (12.0) Sq .472 (6.3) .248 (7.0) (4.2) .276 .165 (11.5) .453 (3.1) .122 Extended Actuator (6.3) .248 (7.3) .287 (0.4) .016 (7.4) .291 (11.5) .453 (0.3) Typ .012 (3.1) .122 (10.0) Sq .394 (0.8) Typ .031 (5.08) .200 JB15LPC-JC Spring action terminals conform to .100” (2.54mm) PCB spacing Framed Snap-on Cap (10.0) .394 (0.4) .016 (10.0) .394 Short Actuator (6.3) .248 (7.0) .276 (4.2) .165 (11.5) .453 (3.1) .122 Extended Actuator (6.3) .248 (7.3) .287 (0.4) .016 (7.4) .291 (11.5) .453 (10.0) Sq .394 (0.8) Typ .031 (5.08) .200 (12.3) Sq .484 (0.3) Typ .012 (3.1) .122 JB15HBPC-BC Spring action terminals conform to .100” (2.54mm) PCB spacing 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Low Profile Process Sealed Tactiles LEGENDS Series JB Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com For other legend support options, customers may either contact the factory and request the JB Legend Packet, or utilize the general information and basic specifications presented below. Laser Etch, Screen Print or Pad Print Epoxy based ink is recommended. Recommended Methods: Laser Etch on clear lens, Screen Print, or Pad Print on lens; Screen Print on film insert. Epoxy based ink is recommended. Lens N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com LM PW R Suggested Printable Area for Cap, Lens, or Button Recommended Methods: Laser Etch or Pad Print Epoxy based ink is recommended. O P U (0.76) Typ .030 (0.76) Typ .030 N (10.0) Sq .394 (10.48) Sq .412 (12.0) Sq .472 (10.48) Sq .412 (12.0) Sq .472 (6.94) .273 (8.46) .333 (0.76) Typ .030 Shaded areas are printable areas. Suggested Printable Area for Film Insert (20.0) R .787 Film Insert Film Insert: Clear Polyester 7 mil maximum thickness Additional methods for legends are engraving the lens and laser printing on film inserts. Maximum depth for engraving is .012” (0.3mm) on the cap lens. Enamel paint is recommended to fill the engraved area. 03-07 O N Translucent White or Colored Diffuser Frame (8.38) Typ .330 (9.9) .390 Shaded area is printable area. Additional Methods